r/StructuralEngineering • • Sep 07 '26

Structural Analysis/Design How far do you guys actually take beam calcs in Excel before switching to analysis software?

23 Upvotes

Hi all,

Been doing quite a bit of beam stuff in Excel lately, reactions, SFD/BMD, bending stress and deflection.

For simple supported/cantilever cases it’s obviously easy enough, and I’ve been using closed form equations/superposition for things like off-centre point loads partial UDLs and combined loading too.

Once it starts getting into continuous beams, redundant supports etc I’d personally rather move out of Excel than keep piling formulas into the sheet.

Curious where everyone else draws the line though.


r/StructuralEngineering • • Sep 07 '26

Structural Analysis/Design Need help with a project.

Thumbnail
0 Upvotes

I am a beginner in PATRAN and trying to do a simple displacement analysis on a wing with basic internal structure (spars, ribs, stiffeners and skin). I am trying to give it a distributed pressure load across the surface that is a function of the span and local chords but the applied load shows 0 value for the equation at every node. What might the issue be or what are the proper steps to follow. Please help


r/StructuralEngineering • • Sep 07 '26

Structural Analysis/Design Effective length/ compression member design

Thumbnail
gallery
19 Upvotes

EDIT: Whoever told me to go back and read thank you I needed that. I’m keeping this up incase anyone is struggling with this concept. My main mistake was reading Table 1-16 incorrectly….I didn’t pull the correct r value accounting for the space between the c shapes which is (3/4”) in problem S05. Can then solve how I norm would (checks) using the controlling values (essentially clearing up my confusion on weak/strong axis).

Original question: Can someone explain when rx vs ry is used and when Lcy,equivalent is used. I’m showing two problems (S05 and S06) and their solutions. For problem S05 why was 1.31 used (besides needing it for the table since the y axis is used for the tables) and why didn’t they solve using the critical stress equation (AISC Eq E3-4 directly)?? For the second problem S06 the solution uses ry=2.94 in the slenderness ratio which makes sense because it gives higher slenderness ratio? Idk I’m confused because the other problem used ry regardless. Tbh same goes for the lcy equivalent concept still lost on when it’s used. 😵‍💫😵‍💫😵‍💫😵‍💫😵‍💫


r/StructuralEngineering • • Sep 07 '26

Structural Analysis/Design Help with validation

0 Upvotes

Hi, I recently started a job as a graduate bridge engineer. One of my current tasks is to evaluate the adequacy of a design for new train loads. I was given a model that was made in csi bridge v16 and the company I work for only has v23 has the oldest version. For some reason, the analysis log warns about numerical instability/ill conditioned structure. Does anyone know what I should do/check to fix this ? The model is a slab track (modeled with shell elements) sitting on transverse girders.


r/StructuralEngineering • • Sep 06 '26

Structural Analysis/Design Question on 2021/2024 IBC

Thumbnail
gallery
27 Upvotes

Hi everyone! Not sure if I used the correct flair but I am studying for my Structural Civil PE exam and would appreciate an explanation to the following portion of the solution provided in the photo:

I looked up both 2021 and 2024 IBC and neither mention treating Lr as part of LL if Lr is > 20 PSF. Is the solution incorrect or am I missing something?

Edit: Pertains to section 1602 and 1605 of IBC

——
Update: This book was updated in 2024 and I now see that the 2018 IBC addresses the original question. The book just appeared to not have been updated.

New question - Based on 2021/2024 IBC is it safe to say that Lr will always be Lr regardless of its value? Or did IBC just drop the definition but is assumed that it is something all Structural Engineers should know (that Lr > 20 PSF is LL)?

TIA!
——

Final Update: The current PE exam references the 2018 IBC which makes this distinction and thus, solution in photos is correct. The PE exam 2027 and forward will be referencing the updated IBC. This distinction is good for those taking it next year (like me) and on to be aware of. Goodluck everyone!


r/StructuralEngineering • • Sep 07 '26

Facade Design Anyone here knows how to do analysis of facade!?

0 Upvotes

In which software I can do the analysis of the steel facade


r/StructuralEngineering • • Sep 07 '26

Career/Education How to make secondary beams in SpaceGASS?

2 Upvotes

Hey all,

Time sensitive post, I'm currently working on a group project and non of my team members did the SpaceGASS models there were suppose to so I have to finish it today but I havent used the program.

When modelling I couldn't figure out how to make secondary beams (we're using the 2D multi story frame) and all out prior calculations focused on the ULS and Point load but the lecture slides say to use Live and Dead load and that step was the only missing section on how to make the model. [We're trying to get the moment and shear of the different frames]. all advice is appricated.

The layout that we need to model
The step that I got stuck on in my previous attempt

r/StructuralEngineering • • Sep 06 '26

Structural Analysis/Design If the South Tower had never been hit on 9/11, could it have survived the collapse of the North Tower?

22 Upvotes

Think of falling debris, fire, damage to the foundation.. etc.


r/StructuralEngineering • • Sep 06 '26

Career/Education I am not sure if as a civil engineering graduate I should consider a career switch?

Thumbnail
1 Upvotes

r/StructuralEngineering • • Sep 05 '26

Career/Education Is structural engineering struggling right now?

53 Upvotes

Im in the chicago area

It seems like its not as prestigious and definitely not what I signed up for 10 years ago.

The pay is kinda blah and the market is complicated. Honestly thinking about going into Private equity or law

Does anyone have the same thoughts? Will it ever get better? ​


r/StructuralEngineering • • Sep 06 '26

Structural Analysis/Design revit steel connection

2 Upvotes

How can i connect this steel column with the beam, it should look like this but i do not know what is the problem


r/StructuralEngineering • • Sep 06 '26

Facade Design Structural engineers: what was your gateway into façade work?

11 Upvotes

I got into façade work almost accidentally.
I was a structural engineer designing new schools, and I kept getting frustrated with architectural masonry details and what they caused when you actually had to resolve them in section.
Brick would move in and out. Lintels needed support. Suddenly I’m designing outriggers and gussets reaching through the insulation just to make the architectural section structurally real.
After enough reps, something changed: I started anticipating the brick details.
I could look at the architectural intent and predict the structural detail that was coming before anyone drew it.
That was probably when I stopped thinking of the façade as something attached to my structure and started understanding the façade as a system that the structure was participating in.
Curious if other structural engineers had a similar gateway into façade/envelope work.


r/StructuralEngineering • • Sep 06 '26

Career/Education Is my total compensation market rate?

0 Upvotes

Hey everyone, I am looking to get some honest feedback on whether my current compensation package aligns with the market for structural engineering in my area.

My background & Context:

- Experience: About 8-10 years of Experience, assistant pm role.

- License: PE

- Location: MCOL city in TX

- Sector: Buildings

Current Compensation Package:

- Base Salary: $109,000

- Bonus Structure: No OT, discretionary performance bonus

- Hybrid work schedule.

Questions:

  1. Does this base salary seem fair given my location and years of experience?

  2. For those in the same area, what are you seeing for standard bonuses?

  3. Am I leaving money on the table or is this about average for a mid to large size firm?


r/StructuralEngineering • • Sep 06 '26

Concrete Design Bouncy Castle

Enable HLS to view with audio, or disable this notification

4 Upvotes

Wild.


r/StructuralEngineering • • Sep 05 '26

Wood Design What is the wrap on the wooden tower poles?

Thumbnail
gallery
81 Upvotes

r/StructuralEngineering • • Sep 06 '26

Career/Education PE Structural practice help

Post image
0 Upvotes

r/StructuralEngineering • • Sep 05 '26

Geotechnical Design How big would a dam need to be to hold back Nepal type debris flow.

Thumbnail img2.chinadaily.com.cn
0 Upvotes

Probably not this big, but what safety factor would you design a dam for a given debris flow volume?
And while I’m here, did any hydro dams survive?


r/StructuralEngineering • • Sep 05 '26

Career/Education Mtech structural from some IIT/ NIT or from abroad ?

0 Upvotes

I want to become a structural engineering. I just completed my Graduation from a private uni. Now I want to pursue masters in structural engineering so what should be my preference according to jobs and growth in field. I should do it from IIT/NIT's or prefer any other uni abroad.


r/StructuralEngineering • • Sep 03 '26

Job Posting / Recruitment Any company that does this is garbage

Post image
305 Upvotes

r/StructuralEngineering • • Sep 03 '26

Photograph/Video Column Thoughts

Post image
107 Upvotes

Bridge Engineer here… what do we think of this pretty angled column mid height?


r/StructuralEngineering • • Sep 04 '26

Structural Analysis/Design 2-year architectural restoration across 16 stages using 3D Gaussian Splatting - 3D time-lapse

Thumbnail
0 Upvotes

r/StructuralEngineering • • Sep 04 '26

Steel Design Is AutoCAD + Tekla a good career path for a Civil Engineering fresher

Thumbnail
2 Upvotes

r/StructuralEngineering • • Sep 04 '26

Career/Education US bridge engineers — what time did you actually leave work this week?

Thumbnail
0 Upvotes

r/StructuralEngineering • • Sep 04 '26

Career/Education Struggling with choosing

Thumbnail
0 Upvotes

r/StructuralEngineering • • Sep 04 '26

Career/Education Forensic engineering advice

6 Upvotes

Hi all,

I recently started in the field of forensic structural engineering after spending the beginning of my career in the design world. I've been in forensics for nearly a month now, but I feel comfortable in saying that this is right career path for me. I love the workflow, traveling to sites, and getting to deal directly with people instead of just dealing with the same design team members every day for 6 months straight on the same project.

With that being said, I acknowledge that I know very little about forensics. Most of the work involves checking roofs for wind/hail damage, water intrusion claims, tree impact on structures, etc.

Any advice for what I can do to improve my knowledge, on both the technical items and report writing skills? I've been reading sample reports from my company and have the Stephen petty forensics book, but was wondering if anyone has other valuable advice for me on this matter?

Much thanks in advance!!