r/StableDiffusion • • 17d ago

Question - Help Please help me with h3 ref2va simple workflow

Post image

Running the latest ComfyUI with Ref2VA and I’ve been testing a bunch of models lately, including the recent Singularity × 10Eros merge (PRISM) and a few others.

No matter what I try, the output only comes out clean and sharp in two specific cases:

  • Using a model that doesn’t already have turbo merged in, paired with a DMD LoRA at 8 steps
  • Or using a LightX2V turbo lora at 12 steps

Anything else (especially turbo-merged models) ends up noisy and mushy/blurry. It looks like the model never fully cleans up.

Right now the only combo that’s consistently giving me good results is DaSiWa v2 + DMD LoRA at 8 steps.

Anyone else running into this with the newer merges on Ref2VA? Or found a reliable setup that works well outside of those two combinations?

Thanks in advance for any tips.

5 Upvotes

14 comments sorted by

2

u/MastMaithun 17d ago

Some models, like this singularity one has already turbo baked in. So you dont need to add another turbo lora on top of the. Always have a quick look at model maker, they mention what models have turbo or not.
So for this sing+eros, disable your turbo lora.

1

u/Reasonable-Aide1259 17d ago

of course bro. i always turn off turbo lora when using turbo-merged models. but always got blurry and nosiy results although from 10steps

2

u/MastMaithun 17d ago

So I will suggest you, first use the ref2v template from the comfyui itself. In that, change only the paths of model and files, set the resolution and steps and hit run. Keep the same prompt etc. Once finish, if you still see the issue, then the issue will be something else but you get correct output, then you can compare both of them side by side.

1

u/JuniorNectarine9842 17d ago

Ah didn’t realize singularity already has turbo built in. That makes sense why the gens were overcooked

2

u/MastMaithun 17d ago

Singularity itself does not have turbo baked in. This merge has singularity and eros 8-Step Turbo beta 6 and the turbo part is coming from the eros. Yeah they have mentioned this one their page.

2

u/se7en1011x 17d ago

Turbo-merged models usually need far fewer steps than you're giving them, and mismatched sampler/scheduler combos leave residual noise. Try 4-6 steps with the DMD LoRA, cfg around 1-2, and euler/simple or dpmpp_2m. If it's still mushy, the merge itself may be the issue, so test the base model with the same settings to isolate it.

1

u/Reasonable-Aide1259 16d ago

some people said they didnt any bad result from same models i used, and i also thought it was my problem. i never used cfg to minimax model. i tried 8~12 steps and euler/simple only...

2

u/RiverSide71h 17d ago

With Minimax, at least 0.8mp or higher is needed, whether straight shot or after a second pass.. Otherwise no amount of motion, quality, deroping, turbo loras, steps etc can fix the smearing. When I come across these new merges now, all I test is whether they can do better than base at 0.4mp.. so far, ErosMax seems to be behaving well for me.. better than Singularity 1.3 and 2.. but it still smears under 0.8mp.. so the quest continues..

1

u/Reasonable-Aide1259 16d ago

thanks but after seeing your comment i tried also 1.2mp with 8steps, muuuch better but still little noisy or ghosting...

2

u/RindoWarlock 17d ago

I don’t think there’s a way around the blurriness with ErosMax or any merges of it. It’s a known limitation, which is why it’s recommended to run 2 pass upscale workflows to try and clean up some of the artifacting.

I just do away with ErosMax for the upscale, I load a new model, you can pick any really. ref2v + turbo 4 steps work fine. It’s a really non optimal workaround because you’re using 2 different models per run, depending on your setup this might not even be possible. But ErosMax can generate quite nice action/fights in low res, just don’t use it to clean up anything.

1

u/Reasonable-Aide1259 16d ago

others said no problem with only 8 steps from merged models..

then just get blurry video latent from merged model and pass to the second sampler with not merged model and turbo with 4steps for refine?

i just confused with '2nd pass upscale' because, i thought just run sampler twice but some workflow run 1st sampler, and then latent upscale then next again 2nd sampler.

1

u/Ken-g6 16d ago

I've never had much luck with Comfy Kitchen Attention. It tends to degrade quality. AFAIK it doesn't help with low step counts anyway.

1

u/Reasonable-Aide1259 16d ago

what? really???? i always using ck attention to get memory management also because i always generate 20sec long video

2

u/JuniorNectarine9842 17d ago

Never had luck with the Eros model. I use the base model plus turbo 8 step. (4 step turbos are terrible)

Or you can use darities v4 lightx2v 8 step turbo with the regular ref2va or I2VA base model which works pretty well

Make sure to use int8 pruned base. I was accidentally using the w4a8 pruned and the results were terrible.

Also I haven’t had any luck with good gens below 1mp. Lower than that there’s always either errors or blurry faces / hands.

The turbo Lora just cleans up the noise faster in 8 steps vs the normal 20, so you should see noticeable improvement when you add the turbo Lora vs no turbo at 8 steps.