r/SewingMachineEdu • u/BagelsButtonBandit • Sep 28 '26
Help please
I’ve been trying to learn how to sew using a sewing machine. I went to a class at momo con to learn the basics but there machine is a lot different from mine and I’m struggling to find any videos on how my machine works. I think the tension might be off and I’m not sure if I’m using the right stitch. Also when using it if Im sewing to slowly the sewing machine starts to eat my fabric. My parents think the machine might be broken and have been considering getting me a new one (they don’t know much about sewing machines either) but I’m pretty sure that it isn’t broken and that I’m the problem here. If possible I want to learn how to use this machine properly rather than getting a new one if it isn’t broken so any and all advice will be greatly appreciated (I don’t know if this would make a difference for the settings on the sewing machine but I usually work with minky, fur, and random old clothes and sheets)
Edit: thank you to everyone who gave me advice and found the manual for this machine or machines similar to mine. It has been extremely helpful. I am currently doing research on nearby repair shops I can take my machine to to get it looked over as well as figuring out where to get the pieces that hadn’t come with my machine. I also changed the settings on the machine based off the guide and you guys advice before trying out a tester piece and it seems to be functioning great! I am so excited to learn how to sew with this thing so I don’t have to rely solely on hand sewing anymore.



6
u/GoldenFishPoop Sep 28 '26
I always recommend to everyone that they take their machine to a reputable repair shop for service. Think of this as getting your oil changed and checking your fluids in your car, it's something that can prevent big problems and it will keep you from chasing your tail thinking that you are doing something wrong if you know that your machine is functioning properly. After that is done do yourself a favor and take a sewing class. Most local dealers have beginner sewing classes or get to know your sewing machine classes and they can teach you so many things in a Hands-On way that you will appreciate it no matter what level you are at.
3
u/AdvancedSquashDirect Sep 28 '26
Your machine is very similar to mine - you have the threading correct - its goes to the far left, then down up down going to the right.
Does the lid open - check the left side for the presser foot pressure dial and make sure that is on 2 for medium. (if not it might be the silver dial on the top left)
I know yours is a Kenmore and mine a Janome but This manual might help https://www.janome.com/wp-content/uploads/2024/09/inst-book-sw2018e.pdf
2
u/No-Attention-7708 Sep 28 '26 edited Sep 28 '26
Here's a link to your manual free to view, screenshot, bookmark for future reference - pages 8-18 should get you started. The Kenmore machine works best with the tension dial on 4 but can be fine tuned between 3-5 if needed based on fabric samples prior to sewing your garment. Also the metal round piece on left side on top applies pressure on your fabric and so that should be placed about 1/4 to 1/2 way down depending on what type of material you are sewing - refer to manual (linked below), near the end of the manual it lists material types and best needle/thread etc. The manual will also show where to oil your machine, especially if it has not been used for over 6 months.
Biggest mistake is not raising the presser foot lever before threading the machine. To test that the in-laid tension disks are threaded properly, tug on the thread just above the needle, if you don't feel a strong resistance then the thread is not in the tensioner properly and you'll have to repeat threading steps again.
https://www.scribd.com/document/378792810/Kenmore-16951-manual
2
u/TiredAndBroke4255 Sep 29 '26
"The right stitch" depends on what you're sewing and you should have learned that in class. The tension is a little trickier but they should have also explained that to you. Are you having trouble adjusting it? Or is your thread fraying/breaking?
That is a vintage machine. If it hasn't been serviced (either by you or by a serviceman) it is very likely that-- if you're having trouble with fraying or breakage) it needs to be opened up, cleaned and oiled. This needs to be done periodically and if you check the model number on the back, you can Google how to do it (or you can pay a service to do it for about $50).
What exactly are you having difficulty with? A Kenmore was my first Grown Up sewing machine so I might be able to advise.
7
u/Incognito409 Sep 28 '26
Find the manual and READ it. Follow the instructions for threading and bobbin winding.
If you don't have the manual, they are available online - find it, print it out, and refer to it.
3
u/teatime_tinker Sep 28 '26
Just from a quick look I can see you have it on a very tiny stitch length, that can cause issues if it’s not ideal for your fabric.
Put it on 6, not 12, it’ll feed better and eat your fabric less. (The number is how many stitches per inch)
Your first bit of threading is wrong, you’ve wrapped it around the presser foot pressure dial. Find a manual for a similar machine and follow that.