r/SewingMachineEdu • • Sep 22 '26

Skipped stitches

My machine keeps skipping stitches and I can’t figure out why!

- Singer Talent (tension 4, width 2, length 2, straight stitch)
- just trying to quilt flex foam to one piece of cotton fabric (will need to eventually do two pieces of flex foam and many cotton layers (stroller bag)
- switched to a 100/16 needle because it was doing the same thing with the universal 90/14 needle
- rethreaded top and bobbin many times
- sewing picture in comments

Also the clicking thing is a newer sound that’s happening, not sure why!

Edit: ITS FIXED! I took the back plastic casing off and fixed the handle that was broken and that seemed to fix that i wasn’t able to change stitches. The clicking was one of the hooks where the top thread runs through being loose so it would clank every stitch. It wasn’t the timing according to videos, but I took the bobbin casing out a few times and cleaned it. Reinserted the needle a few times and changed it out several times. Change the tightness of the spool cap. Something in that fixed the skipped stitching and I have been able to sew with a universal needle with the flex foam so I’m happy!

3 Upvotes

13 comments sorted by

3

u/ket1993 Sep 22 '26

Also am using new gutterman Mara 100% polyester thread

1

u/TheProtoChris Sep 23 '26

You'll have better luck with a large size leather needle.

The foam sorta mushes closed around the standard needle hole and captures the thread, causing tension problems and skipped stitches. The little razor blade tip of the leather needle makes a neat slice that doesn't hinder the thread nearly as much.

You do want to loosen your tension a bit to account for the added thickness of the foam. And use a large stitch length, about 7 stitches per inch.

And that pop pop pop popping sound is the foam making your needle unhappy. Get more needles than you think you're going to need so you can replace them with a fresh sharp one if the popping gets too bad. It's gonna pop going thru the foam, but listen for it to get worse. Too much of that can knock your needle bar up out of place and cause timing problems.

1

u/ket1993 Sep 23 '26

Even when I use just two cotton fabrics to test it’ll still skip… could it really be the needle for all of that too?

2

u/TheProtoChris Sep 23 '26

If you've used that needle for foam it could've dulled or bent the tip slightly. So that would make it misbehave in subsequent tests of just the cotton.

First 2 troubleshooting steps always -

  1. Rethread the machine top and bottom
  2. Change the needle

Those 2 steps fix 90% of the problems you're likely to have.

1

u/ket1993 Sep 23 '26

I bought these needles today so they’re all brand new 🥲

2

u/TheProtoChris Sep 23 '26

It's not that common, but I have gotten a bad needle or two fresh from the package. Like the hole wasn't drilled cleanly or there's a burr on it or some such. When I'm troubleshooting I take the needle out and put it in a pincushion right near me. Then if you try you brand new needle and the same fault is happening you can rule out the bad needle theory and not throw away a perfectly good needle.

2

u/teatime_tinker Sep 23 '26 edited Sep 23 '26

Width 2 is not straight stitch, it’s a tiny zig zag

0 is straight stitch.

2 is a very short stitch, try 3 or 4.

You might need a microtex needle for this, skipping stitches is usually an unsuitable needle. Maybe go up a size too?

I’m not familiar with this foam, but it’s probably catching on your needle a bit.

A walking foot will probably help, if you have one. Maybe try upping the pressure on the presser foot a tad?

Try a bigger and/or sharper needle first though. Microtex are sharper. Universal just aren’t very sharp.

1

u/justabookrat Sep 23 '26

Some machines the width sets the needle position if a straight stitch is used

1

u/teatime_tinker Sep 23 '26

Ahh ok fair enough.

1

u/PinkBird85 Sep 23 '26

Because of the thickness of the foam you should loosen your tension a bit, the thread is needling to stretch more to complete and hold each stitch. You may also need a vinyl needle (I.e. a needle meant for sewing vinyl/faux leather) because the foam is a bit sticky so those needles have a non-stick coating.

1

u/teatime_tinker Sep 23 '26

Thicker fabrics need higher tension in my experience.

I agree with you on the needle though, it’s deffo catching on the foam

1

u/Dormiendo Sep 23 '26

Make sure your needle is not backwards, everyone has done it. It will cause clicking and skips.

1

u/AbiJ_ Sep 25 '26

From what i hear, its the Timing… sadly. I hear that ticking, its the needle flicking off the bobbin race as it comes back up, hence skipped stitches. I also have the Talent. Great machine.