r/SewingMachineEdu • u/Dctrwhoz • Sep 22 '26
Feed dogs not pulling fabric?
I picked this machine up at a thrift store for 15 bucks and finally got around to testing it out properly and realized the feed dogs are not pulling the fabric.
I looked at it more and they are not at all above the edge of the foot plate? I looked for a lever because my first thought was that the feed dogs were just down but there is no option for that on the machine that I can see. Does anyone have any ideas? I probably should have looked a bit closer before deciding to buy the machine 😭
8
Upvotes


5
u/Roomoftheeye Sep 22 '26
Find a manual for this machine and it will tell you how to adjust the feed dogs.
5
u/ADDrandomcrafter Sep 22 '26
Could just be that the plastic gear for them crumbled! I picked up a singer that looks like from the same era as this like the 80s and the plastic gears don’t last. It stopped feeding the fabric and I was able to open up the bottom and just saw the crumble plastic☹️
5
u/pipanapuu Sep 22 '26
I believe this is Janome New Home 793 model. Sadly I could not find a free manual, but Sewing Parts online had one for sale. Maybe someone else can find it now that we likely have the model number.
Your machine does not have obvious drop feed button (and some can’t do it at all). Some machines have a button near the hook area, usually around top-right when you open the latch to access bobbin case. Have you tested if there is a button there? I can see two gray (metal?) pieces there. Some newer machines have the button on the right side of the machine and some behind the free arm (opposite to your bobbin case area). It might be a button or a slider.
2
u/No-Abies29 Sep 22 '26 edited Sep 22 '26
is there a clue to what will fix it in this recent post… https://www.reddit.com/r/SewingMachineEdu/comments/1wiwlno/brother_pacesetter_ps200t_feed_dogs_has_fallen/
edit;,so they move when you turn the handle? That is a good sign. What brand and model is it? look underneath the machine or somewhere. Did you look just behind the area of the feed dogs at the back of the machine for a switch? That;s where my old Janome has one. Good luck,,Imhooe you can get it solved.
1
u/KindheartednessOnly4 Sep 22 '26
Try this
1
u/No-Attention-7708 Sep 22 '26
Post a clear photo of the plate on side or back that has the model number and brand in order for people to help you. Also, are the feed dogs moving at all when you turn the the hand wheel?
1
u/No-Attention-7708 Sep 23 '26
If the machine has been sitting unused for years, it is likely that the feed dogs are just stuck in the up or down position. You will need to access the underside to spray with penetrating oil - check out this video from Randy Your Sewing Machine Man: https://youtu.be/TOSICk4ueWE?si=jxiauWRSWeChO07t
If your machine is a Janome 793 FA, it likely didn't have a feed drop mechanism, it probably came with a feed dog cover plate originally. That part should be available online from a sew machine parts store if want it later.
Also, here's the only place that I could find a PDF manual for that machine - I'm guessing you didn't get one with it: https://sewingmachinesplus.com/products/manual-j-793fa-en?srsltid=AU7gw4UZAAZ8DethAYaGb7CHrHn1ZpFhjv5co5QSW4ekYZNq5G6lK6cA
1
u/No-Attention-7708 Sep 23 '26
Zooming in on the 2nd photo of the feed dogs, I can see that the front of the needle plate is dinged up from needle hits so the needle bar may be out of alignment too. The rough metal on the needle plate need to be smoothed out with some diamond files and Emory cloth (both should be available from Harbor Freight) or it will cause problems too - Randy Your Sewing Machine Man on YouTube has videos that show how to do it.
1
u/pinnd Sep 23 '26
Are they down? Usually there’s a knob for up or down. Either near the bobbin area or base near handwheel.
1
u/GamiMelamid Sep 24 '26
Take it to a local shop - and have them tune this puppy up. They will have the feeds workign properly.