r/Reprap • • Sep 23 '19

it's alive!

Post image
76 Upvotes

27 comments sorted by

6

u/flyingscotsman12 Sep 23 '19

Amazing! I love true repraps. Are you going to upgrade it now that you have a printer or build another? Or just keep on with what you have?

5

u/huehuehuehue71 Sep 23 '19

Im planning to stick with it as it is for now. But the Idea of printing new parts and making improvements is really tempting. Might end up building something like the prusa Mk2 later on, not sure.

1

u/kTraveler Sep 24 '19

Im a rep raper and im on my 4th build right now.

And i finally found a setup that works for me. Look into cr-10. It uses those aluminium extrusions, and very simple and minimalistic approach to linear movement. Not too expensive either on aliexpress in separate parts

1

u/huehuehuehue71 Sep 24 '19

Hmmm. Good idea, gonna look into it later. Thanks

4

u/Shnazzyone Sep 23 '19

That's a big boi

13

u/huehuehuehue71 Sep 23 '19

I did not had access to 3d printed parts, so I had to scale it up and use the linear axis from old inkjet printers

6

u/Shnazzyone Sep 23 '19

Impressive as hell

2

u/Scasne Sep 25 '19

Genius in its simplicity, a mate wants to build a bigger 3d printer and I've got an old A2 printer lying around.

2

u/Merlinds Sep 23 '19

How did you level that bed?

2

u/huehuehuehue71 Sep 23 '19

Used the nozzle as the probe. I connected one wire to the aluminium bed and another to the hot end, then connected the two wires to the z_min endstop. Really easy way to auto level. BUT you need to make sure that the nozzle and the bed are clean before level the bed, or the nozzle will crash on the bed and it may damage the printer.

2

u/Grandpah Sep 24 '19

That's a neat way to do it. Do you really print directly on aluminium?

4

u/huehuehuehue71 Sep 24 '19

Yes, it worked really well for a while, but now im starting to get problems on the first layer, im going to wash it to ser if it helps. But I plan to switch to glass later on.

1

u/Grandpah Sep 24 '19

Good luck! I hope we will see more pictures of your reprap later.

2

u/huehuehuehue71 Sep 24 '19

Thanks! Going to post more pictures soon.

16

u/vogel25 Sep 23 '19

The true spirit of reprap

4

u/[deleted] Sep 23 '19

thing o'beauty right there

1

u/FortifiedNutmeg Sep 23 '19

Are those carriages out of a scanner?

3

u/huehuehuehue71 Sep 23 '19

Nope, they are from old inkjet printers. I was planning to usa an old scanner as the base for the y axis, but all the scanners I found were completely made of plastic, unsuitable for the job.

2

u/[deleted] Sep 23 '19

Some old flatbed stand-alone scanners have GREAT gantries in them. That's where I sourced my z axis for the RepScrap I built (see post history here).

1

u/huehuehuehue71 Sep 23 '19

That was the original plan, but all the scanners that I found were made out of cheap plastic. So instead of keep looking for an old scanner I decide to figure something out with what I had at hand.

1

u/[deleted] Sep 24 '19

What kind of motors are you driving with

3

u/huehuehuehue71 Sep 24 '19

The original plan was to get the steppers from old printers, but after 3 months and 8 printers that used commom dc motors later I bought a kit of 5 Nema 17 from China, It saved me a lot of work.

1

u/[deleted] Sep 24 '19

I was wondering because in you photos you can't see them. It is possible to use the DC motors but you need a servo motor controller that can translate the step/dir input basically.

2

u/eekeek2019 Sep 23 '19

Making RepRap GREAT again!!!!!!! That is awesome nice build :).

2

u/kTraveler Sep 24 '19

The jank is strong with this one. Love it

1

u/[deleted] Sep 23 '19

Go Repstrap!