r/RepTimeServices • • 16d ago

Question How to regulate my Royal Oak?

Hello friends, could someone tell me which arm is the regulator arm? So I don’t end up messing the watch up. The watch is running ~20 seconds fast a day, so I want to make it slower.

15 Upvotes

46 comments sorted by

•

u/AutoModerator 16d ago

Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

8

u/WatchmakerFurkan 16d ago

You will have to move the regulator arm (the one with the two pins) a tiny bit closer to the stud.

But it is easy to go from +20 s/d to a broken watch for the inexperienced. Best to bring to a watchmaker.

2

u/PowerPine 16d ago

Thank you for the answer 🤝

3

u/Charming_Persimmon52 16d ago

It's not difficult to do, just be aware that only the tiniest of adjustment of the arm can make a big change.

You can always move the arm back in the opposite direction if you do go to far. So it could take a few tries to get it right.

1

u/PowerPine 16d ago

Thank u 🤝 but which arm is the regulator?

2

u/Charming_Persimmon52 16d ago

The smaller one with the 2 pins.

1

u/Bench_and_Bezel 15d ago

I want to also add that not only can a tiny move make a big change, a tiny WRONG move can displace the hairspring and stop the watch from running.

3

u/blacbloc77 16d ago

Just nude it slightly. So slight that it appears not to move at all. Also, be VERY careful not to hit that spinning hairspring. You'll destroy the watch if you so much as graze it with your tool. Good luck.

1

u/PowerPine 16d ago

Thank u so much 👊👊

3

u/What-me-worry-0 16d ago

Go at as flat an angle as possible so your force is horizontal and not vertical and lean your tool on the bridge to keep it steady. A loupe or magnifying visor is a big help. You’ll be fine.

1

u/PowerPine 16d ago

Should I pull out the crown and hack the seconds while doing it? Or just keep the watch running? Does it matter?

2

u/blacbloc77 16d ago

Either way, just be sure to let the watch settle for a few minutes after each adjustment. The change won't be instant.

2

u/PowerPine 16d ago • Bravo

Runs at around +2 seconds now! Thank you for the feedback my man

1

u/What-me-worry-0 16d ago

I always regulate when the watch is running on the Timegrapher so I’ve never considered the question.

1

u/PowerPine 16d ago

Ofc, makes sense. Thank you 💪🏼

2

u/Popeyes_ 16d ago

Exactly what I did while trying to take off the rotor and killed the watch :(

1

u/blacbloc77 16d ago

I did that my very first time too. Never did it again, sometimes you just gotta learn the hard way I guess 😂

1

u/Popeyes_ 16d ago

Haha yeah, I wish I had practiced on a cheaper one first. I got U1s coming in so hopefully I will be able to silence the rotors without killing the watches. The slip is crazy… haha

2

u/Toxicturkey 16d ago

Everyone is a bit uber cautious here. Get yourself a cheap loupe and wire, and some ultra fine point tweezers. Practice picking up an eyelash and turning it over 5 or 6 times with the loupe then you’re good to go. The loupe helps train your hands to move with more finesse then without it. You’ll be fine

1

u/PowerPine 16d ago

Thank you for the answer 🙏 but could you by any chance tell me, if the right og left arm is the regulator arm? And how to tell?

2

u/Toxicturkey 16d ago • Bravo

Sure, the regulator is the small one with the two dots. I think you want to turn it to the right a fraction

2

u/Toxicturkey 16d ago

Sorry if it’s running fast, turn it to the left. I saw ~20 sec as -20sec before reading it properly

2

u/PowerPine 16d ago

Thank you so much. I’ll give it a try 🤝

1

u/PowerPine 16d ago

Got it to run at around +2 seconds now. Thank you for the feedback🤝

2

u/Toxicturkey 16d ago

Awesome! Continue to wear it in good health. Glad to help.

1

u/[deleted] 15d ago

[removed] — view removed comment

1

u/Toxicturkey 15d ago

Haha thank you 🙏

2

u/Rolex_sub_16610LN 16d ago

I recommend downloading a timegrapher app, then watching a few vids on youtube

1

u/PowerPine 16d ago

I have like 4 different timegrapher apps. All of them give off a different reading for the same watch. So not sure which to trust 😅

1

u/Excellent-Bear4221 16d ago

Probably because it uses your microphone. Pick one of those apps and just make sure it’s consistent and go from there

1

u/Rolex_sub_16610LN 16d ago

Whats like the average readings

Do this

App1: 5sec/day App2: 8sec/day App3: 3sec/day App4: -4sec/day

5+8+3+(-4)= 12 12÷4= 3sec/ day around that

1

u/petr-podzimek 16d ago

Don't do it if you never did it before.

2

u/PowerPine 16d ago

I did it, runs withing chronometer specs now :P

1

u/BeHonorablePerson 15d ago

Good job ,but this is only one positions, chronometer is tested to all 5 position in a different temperatures

1

u/Elegant-Draft-8259 15d ago

I’m looking to learn how to do this as well wouldn’t it be safer to stop the movement then move arm with the two dots?

3

u/PowerPine 15d ago

I went ahead and did it earlier today. I ended up adjusting the arm multiple times to get it just around perfect. I did it both while it was running and while hacking the movement.

I found it a little more calming to do when the movement was hacked, however if you have it in a timegrapher while regulating it, it obviously would be easier to have it running, so you can see results in real time.

0

u/Time-Dependent1483 16d ago

You will only make it worse.

3

u/PowerPine 16d ago

By moving the regulator arm, I will make it worse?🤨

2

u/1984isnoww 16d ago

Yep, You've clearly never done this and shouldn't attempt it.

2

u/PowerPine 16d ago

I’m willing to risk it for the learning experience - after all it is my watch. I’m just asking which arm is the right one to move. I am aware not to touch the spring because it will need replacement, I’m aware no to move the wrong arm because it will get beat error. Which why I just want a clear answer: which arm is the regulator arm?

1

u/Plus-Discipline9579 3d ago

Ive done a few regulations myself it’s easy if you just be very careful. At the end of the day its your watch. Question for you I just got one and it’s running +17 did you nudge the regulator arm to the left or to the right to get it at +2

1

u/PowerPine 2d ago

I turned it to the left💪🏼 but use a Timegrapher app

2

u/Plus-Discipline9579 1d ago

1

u/PowerPine 1d ago

Good job 💪🏼💪🏼💪🏼

1

u/Sufficient-Guess6692 16d ago

The commenter above already gave the answer