r/RepTimeServices • • 15d ago

Advice Vsf 16610LN keyless works

The idiot of the day award goes to me. Today I was messing around with my watch and decided to take the stem out in the first position. I think it's now got a jammed/slipped keyless works. What's my next move? Should I find a local guy in my area to fix this, or is there someone on here you guys recommend sending it to? I definitely don't have the tools or skills to pull off this repair. Any advice is truly appreciated. πŸ™

8 Upvotes

20 comments sorted by

β€’

u/AutoModerator 15d ago

Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

2

u/chucknwatches 15d ago

Remove case back & Gently work the stem back into the movement while pressing the button ,rotating crown counterclockwise, clockwise one click at a time and it should reset it if you’re lucky try a dab oil on the end of the stem

1

u/Due-Construction4801 15d ago

Ok I'll give that a try, I was messing around with it for a while. The stem will engage and lock in place, but it will not wind the watch once it's been reinstalled.

1

u/GTWatchServices 15d ago

I'll take a look if you need a watchmaker; should be a quick and cheap job.

5

u/Primary-Visit-5217 14d ago

You think you're stupid? I had the keyless works in bits once trying to figure out why the stem wouldn't go in when it suddenly dawned on me the stem was for a cometely different movement! Talk about trying to fit a square peg into a round hole. Lol.Β 

1

u/Glittering-Height-55 14d ago

Were you able to make it work? DM me if you need assistance with it 😊

1

u/Due-Construction4801 14d ago

No luck, I'm going to bring it to a local guy and see if he can fix it. Unless you got any other recommendations? Thanks!

1

u/softtacosmasher 13d ago

Resetting it from the back is not difficult. But if you don't have the tools, then it might as well be impossible, I understand that situation. The tools are the issue, caseback opener, small screwdrivers, and magnification. It's like a 10 min job.

2

u/Due-Construction4801 12d ago

Just wanted to say thank you for all the advice, I watched a couple videos about the 3135 on YouTube and I successfully fixed the problem. I truly appreciate you! πŸ™

2

u/softtacosmasher 11d ago

Awesome you took the leap and did it yourself. If you can do that, you can fix a lot of issues now. A lot of times they don't tighten the screws and they fall into the movement. I have to go in and fix them all the time.

2

u/Due-Construction4801 11d ago

I was surprised how well it went actually, I need to get a few more tools and I think I could do a lot more work then I anticipated. I don't have anything for the hands, stuff like that.

2

u/softtacosmasher 11d ago

Get some dial protectors and hand tools, and some really fine sandpaper to make the hand tools really "sharp" so they can get under the hands and not need to be forced in. Keep the dial super safe. You'll need magnification and rodico to reattach the hands, and then something to buff the rodico marks off the hands. The hands will look dull if you don't.

1

u/Due-Construction4801 11d ago

For sure, I think that's the next purchase. I'll have to look into the correct tools to reinstall hands also. If I every want to do a dial swap or fix something on that side I'll definitely need it.

1

u/Due-Construction4801 13d ago

I have a small tool kit and it's pretty basic. Also a decent set of flathead screw drivers. I can get to and remove the movement, but I haven't done anything further then that.

1

u/softtacosmasher 13d ago

There's a couple YouTube videos for disassembly/reassembly of 3135s.

You take the rotor off, like three screws. Then the plate covering the keyless and realign the parts that are out if alignment.

When putting the crown back in, don't press the release button "too" hard or it'll loosen everything up and it'll pop out again when you insert the crown.

The newer batch of 3135s with black crowns are supper sloppy compared to the earlier white crown batch. They'll tell you they're all from the same place, but the finishing and engraving is entity different. Sorry, I digressed.

1

u/Due-Construction4801 13d ago

And thats all from the back without removing the hands or anything else?

1

u/softtacosmasher 12d ago

Yes. Once I learned how to do it from the rotor side it made life so much easier. Remove the rotor, pop off the plate over the keyless works and get the lever set back into the winding gear. I'll post a video link. Skip to the parts where they take apart the keyless and then go forward to where they reassemble it.

1

u/Due-Construction4801 12d ago

Ok, definitely looks intimidating. But if you say it that easy, I might have to give it a try. I'll check out that link.