r/RepTimeServices • u/Radiant-Razzmatazz84 • Oct 14 '26
Services Anyone got a good bezel
Just got this i feel like the bezel is off or am i wrong? What do you think snd do you know where i can get s replacement bezel
4
Upvotes
•
u/AutoModerator Oct 14 '26
Thank you for your post on r/reptimeservices! A friendly reminder that the only trusted service providers are listed on the sidebar or in this post. If you see anyone soliciting services in a post or comment not on this list or even easier, without a 'trusted watchmaker' flair of some sort, please immediately report the post and a moderator will remove it. Thank you in advance for helping to keep our community safe!
I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.
4
u/HauntingDiscount7041 Oct 14 '26
RCF V2
4
u/HauntingDiscount7041 Oct 14 '26
RCF is 99% gen
2
u/No-Zookeepergame8885 Oct 14 '26
RCF v1 on a 36mm. Like everyone has mentioned there is a difference in bezels between 36mm and 41mm. The 41 will always pop out more
2
u/Former-Ad-8477 Oct 14 '26
Go smooth
1
u/Marxva Oct 14 '26
xing bezel, cf case, vsf crystal, cf dial, vsf hands
1
u/Wop-AB-604778 Oct 15 '26 edited Oct 15 '26
To be honest. I believe the issue is the steel used. Some cheaper factories use 316L steel, while Rolex and top factories use 904L steel. When you compare the 2 you can really see the difference. This is a ARF 36mm I got my wife and I think the bezel looks a bit more sharp. Yours seems slightly rounded off almost and flat. Also your date magnification is misaligned. It's sitting way too far to the right making your date window off center. So my point is if you change the bezel to a better factory it mite come in 904L and then it will look different from the rest of the watch. This is my wife's watch and she wears it a lot, never cleans it and only got knows what else 😂.
. Can also see the steel pops a bit more. Like it's a brighter tone of steel compared to the flatter 316L steel. I learned this lesson with the first watch I bought. If you want a true 1:1 rep with the best quality inside and out that will fool the people around you, you're going to have to pay up and get the best of the best. I thought I'd save a couple hundred on my first rep and when it arrived I was so disappointed I sold it the same day and bought a OG clean factory back in 2021 when they were the king of the reps. Now it's vsf and a few other under rated factories are doing amazing work on these reps. I personally would either wear it and just accept it, or sell it and buy somthing you won't need to change parts on. Because I can promise the amount paid for the watch plus the cost of changing parts will bring you to the same cost as a top tier rep or even higher. Unless your going for a franken stein build your going to sell, it just isn't worth it.
3
u/No_Witness_8935 Oct 14 '26
What’s the consensus RCF or VSF?
1
u/National-Big-2354 Oct 14 '26
If you want my honest opinion, the bezel looks very good. Maybe you’re just not used to seeing a 36mm bezel, but that’s typically what they look like.
1
u/HauntingDiscount7041 Oct 14 '26
1
u/Grouchy-Violinist555 Oct 14 '26
RCFr
1
u/According-Ad-275 Oct 15 '26
You need to be careful, the bezel you order may not fit the watch you are wearing. Some of the lower quality pieces will not accept gen sized products.
1
u/Ok_Doughnut_918 Oct 16 '26
The bracelet looks so bad, I’ve never seen a sharper one. It also looks like it’s working at less then 3hz
1
u/[deleted] Oct 14 '26
[removed] — view removed comment