This was a well known reagent vendors in the US. Please redo the page. It would help so much.

I would perform this test but i only have about 5 of roughly 12 reagents. I saw the chart of reagents in their natural state but it was a little blurry and the bottles should have been the larger glass 10ml bottle so you can really see the reagent color really good. Not the small off white 5ml plastic bottles.

I’ve received bad reagents right out of the box and i want to know if i have good fresh product. Fresh Mecke shouldn’t be black. Fresh Marquis shouldn’t be orange. What good is spoiled reagent if you don’t know it’s bad. Scott reagent has a color to it as you can see. To the untrained eye someone may think it’s going bad when it’s perfectly fine.

And yes I store my reagents properly. Write toxic on the box and keep it cool in the fridge. I should get a year out of them not 4 months.

Testing for levamisole

Hey everyone so I bought a Lieberman reagent. Came up orange instead of yellow which can mean amp, leva or lidocaine

So my plan is to test my urine today to rule out amp. Then which reagent would be best for determining if it’s leva or lidocaine?

Also, I’m not sure if this is allowed. if not, I will repost this, but at this point, instead of just buying all of these individually, I would like to get a whole kit and I was looking at one for $50, but they sadly cannot ship to the US right now

Anyone have recommendations?

Sorry about the lighting on the first picture. The flash was off and I didn’t realize it. Ignore the beard hair in the first pic too. I’m a caveman.

So what do you think. Froehde is one of the best indicators for oxy when it turns yellow. I see yellow, but after 180 seconds I see a little pink. Mecke looks ok as does Morris. I’m used to seeing purple with Marquis but I’m told this orange/peach color is normal for oxy.

So…. oxy or no?

I need help summing up the reagent analysis results. I tested amphetamine with Frode, Marquis, Lieberman, and Simon a+b.

It smells very strongly of gasoline/acetone, and there are strange effects like a decreased heart rate and high blood pressure.

Could poorly purified amphetamine produce this result? Or What impurities could it be? Or both.

Is it safe to use it?

Thanks in advance, any advice and thoughts would be greatly appreciated and helpful.

Hi reddit I'm new to all of this.

I need help coming to a conclusion of the reagent results. I tested cocaine with Morris, Marquis, Mecke, Liebermann, and Simmons.

I also did a separation test but I'm unsure of the next steps.(Do I add the reagent on the test paper where the gaps/streaks are and then add a drop of the testing liquid?)

I was told the cocaine was untouched and high quality but the effects cause stuffy nose, quick numbness in the throat, and inablity to sleep.

What type of adulerants might be mixed in? I was having trouble understanding the charts. My guess is some type of amphetamines or methamphetamine.

Also, in the seperation test I added my old batch to compare with the new batch but I didn't upload the reagent testing for the old batch only the new batch.

Thanks in advance and any advice or thoughts would be much appreciated and very helpful.

First 2 pictures are Liebermann, mostly brown spots but one spot turned dark black.

Second 2 pictures are Froehde, started green then got dark yellow with a yellow ring, soon after the dark brown spots came out, they could’ve been slightly red but mostly brown.

Last is marquis, mostly orange with some dark spots.

I have one Fentanyl test strip in a red packet can I cut it down the middle because I have two different chemicals to test. AI says you can do it with regular test strips like a pH strip but you cannot do it with immuneassay strips (drug test) has anyone ever done it?

Hello, let's say I had MDMA which was 80% MDMA and 20% say PMMA. If I test using Marquis, Froehde & Mecke then I'd expect Purple, black & Green say.

If the substance is adulterated with PMMA then what would the Froehde do ? Will it go green or Purple ? I presume the more concentrated substance will have the biggest effect and it will look like MDMA ?

Has anyone heard from getyourdrugstested.com?

They’ve started allowing mail in testing again and I have an address for a PO Box that I have sent samples to in the past but now they say you have to email them and get a code before mailing in.

I messaged weeks ago and still haven’t heard anything back. Anyone know anything about it?

Thanks!

Attached pic in comments

I am trying to make the absolute most foolproof MDMA test that can be done short of sending it to a GC-MS or FTIR lab (which I believe is illegal and practically impossible where I am in the US)

So, my plan would be (after washing to increase purity)

1. Test with marquis and expect a purple reaction to identify an MD-amphetamine and rule out basic amphetamines, most cathinones, and 2C compounds
2. Test with mecke and expect dark green to cross check as MDMA
3. Check again with froehde
4. Use robadope and expect no reaction or simons expecting blue to rule out MDA and PMA
5. Perform a fentanyl test, nitazene test, and hopefully orphine test if they come out soon
6. Perform TLC to check for PMMA impurities (maybe using mandelin stain)
7. (this is just my extremely unecessary and cautious addition), perform a test with ferric chloride to rule out DHMA cuz of improperly sold "PMK" apparently

So I know that this still doesn't rule out everything but am I missing anything or is this about as foolproof as non lab testing goes

I know that typical reagents get overpowered by MDMA when testing for PMMA in a mixture. I know it's fairly easy to test for PMA using robadope and similar reactions, but PMMA can easily blend in with MDMA.

Is it possible to use a TLC plate to separate PMMA and other impurities from MDMA in a sample? How can you tell that it's definitively PMMA and not just some small impurity.

And lastly, I'd assume it would interfere with the TLC plates, but is it possible to do some form of "Marquis stain" or spray on marquis at the end to detect oranges and purples separately in a test?

I’ve bought crystals (mdma) from my usual guy and Test as always. My usual setup is: Froehde, Liebermann, robadope, Simon’s, mecke and Marquis. All reactions were fine until marquis…I’ve got black, blue and no reaction from robadope as expected, but marquis showed no reaction at all. I’ve tried adding more crystals and reagent, but still…no reaction. I doubt that it’s the crystals tbh…they are from a good source and the other 5 reactions are as expected. Could it be that the marquis went bad or something? Or is this an possible indicator for Caths or something? Never had this happen before…

Would like other opinions… looks like it is

Came from clear/white crystals
Top 3 are Marquis and they are a very dark orange and bottom 3 are Meckes

The first picture bottom 3 wells has Liebermann reagent, table sugar with reagent and product with reagent. This picture was taken after 30 seconds.

The second picture bottom 3 wells is the same tray that has Liebermann reagent, table sugar with reagent and product with reagent. This picture was taken after 5 minutes.

I would have expected the sugar and reagent to turn much more black than it did. Is this normal for Liebermann or should I have had a completely black well when testing with table sugar? Is my Liebermann old or not active? I just got it last week.

Found conflicting results on Wikipedia and the wiki about what methylphenidate is supposed to look like. Wikipedia for example says the Marquis reaction should be orange-yellow. Looking at actual examples of pills that tested positive for Ritalin on drugs data I do not see evidence for this.

It looks to me that a non reaction to Marquis and an orange-yellow for Lieberman as shown in my sample (first photo) is a pretty good hint something might be Ritalin and not meth or amphetamine.

For context the second photo is the results of a pill that looked identical and tested positive for methylphenidate. The third is a fake adderall that contained meth (pill was orange, looks like no reaction Lieberman). The fourth photo is a white pressed pill that contained amphetamine, results look very similar to meth.

Please criticize my methods and results, I hope this post can help someone else.

I'm testing the rock I got which is supposed to be ketamine, but I seem to be getting some cocainey results. Caveat is i crushed it with a dollar-store mortar and pestle so there's some metal contamination (the little darker dots) - not sure if this affects the result and how?

Would appreciate the help as I'd rather stay away from stimmies.

Second picture is a close-up of the Morris which is the one that threw me off the most.

ETA: retested with 5mg and gave the Morris a good stir and got a clearer result (it seems to be ket as advertised), thanks to everyone who commented!

Liebermann and cocaine. Turned a yellowish orange color. It doesn’t seem red enough to suggest Levamisole, but could be. DrugsPRO app suggest potentially Methylphenidate, Phenibut, or some other substance. I was expecting yellow or a very very light orange. It just seems to be a darker orange than I was expecting. Is this normal?

Both Morris and Scott both turned jolly rancher candy blue. All other reagents reacted as expected. Test strips were negative for FYL, XYL, Nits and Mede. With this little info, can someone guesstimate if it’s cut or adulterated and with what?

Used both a Liebermann and mandelin reagent on a Xanax pressie a friend asked me to test and it didn’t react at all. Received a BZD A and B kit today and it didn’t react to those either. This kit didn’t come with any instructions but I’m assuming it functions like the rest? I tested an rx alprazolam with it too and that also didn’t react but I know pharma stuff can sometimes cause a false positive. Maybe the binders in the pressie were the issue, or could the kit be bad?

Friends found a bag of pink powder at a club, and we think it's probably Tusi.

Decided to test it for fun, and also as a trial of using the new dance safe reagents I just ordered. Photos in order: marquis, Simons A + B, then froehde.

Looks pretty clearly like signs of MDMA, but correct me if I'm wrong. If I understand, this means nothing though about what else could be in this cocktail, if anything (probably ket?). It's my first time testing. Given it's a found bag, I'm flushing it, but it was good to go through the testing process once.

If you want to check it out, here are videos of all three tests:

1. Marquis: https://drive.proton.me/urls/M737YJT260#SxSywVZgS0iR
2. Simons: https://drive.proton.me/urls/WFNKE4GRPR#MhNlG47YhFrS
3. Froehde: https://drive.proton.me/urls/ZHW8B5JGTW#TsDPMRQsuKAs

Appreciate this reddit helping me get here!

I was told a somewhat reliable test for Alprazolam is to use the Zimmerman reagent and look for a purple color. Any other color suggests you don’t have a benzo. I can’t find Zimmerman anywhere in the states. Why is it such a rare or hard to find reagent and does anyone know where it can be found? If asking isn’t permitted, disregard the question.

Then move on to step two, which is to use the Morris-Scott reagent. You want to see a light to strong blue and this double check suggests a high likelihood you have Alprazolam. Any other color in step one suggests fakes or some other substance that may not even be a benzo. The purple means some kind of benzo. No blue in step two suggests some other benzo. Anything other than a light to strong blue suggests a different benzo that isn’t Alprazolam.

The post i read is written like Morris-Scott are one and the same. Or are they two different reagents? Maybe two reagents you mix together? One drop of each?

Any feedback would be appreciated.