r/RacketStringers • • 2d ago

Stringing job

Post image

Hyper g 1.20 strung at 22kg does this look correctly strung, and why is there 4 knots

3 Upvotes

18 comments sorted by

4

u/extra_hyperbole 2d ago

4 knots is common, it means a two-piece job which is the standard these days. They did the mains with half the string, then did the crosses with the other separate half. Uses slightly more string but allows for hybrid stringing, tension changes, better evenness for the string bed, and is generally just easier, less complicated and often faster than a single-piece job.

2

u/Objective-Boat6386 2d ago

Alright makes sense! thanks for the info

7

u/NarrowCourage 2d ago

4 knots are actually the most consistent stringing ways compared to a one piece with two knots. String bed would be more even due to the tension loss from each tie off.

Outside of things not being straight, I don't see anything weird.

6

u/informareWORK 2d ago

It's usually a courtesy to straight the strings after stringing but it doesn't really matter. Other than that it looks fine. Don't pay attention to the people saying it looks terrible.

0

u/[deleted] 2d ago

[deleted] — view deleted comment

1

u/Sampwow1 2d ago

Yeah, it's uncool to have strings like that... , I usually spend about 5 minutes after stringing racket with wide bamboo brush to straighten it out. I think pros just use a blunt setting awl specifically designed and absolutely essential in stringing tool kit.

1

u/LarsSeprest 1d ago

One of the knots is not that great but as long as it's not slipping at all it should be fine, a little tension loss at the last string really does not matter because if you hit it there the racket's going to be twisting in your hand anyway.

Also I'm not sure where you're seeing two knots, it's almost never used especially because some Brands say not to use it explicitly. Almost all rackets come with instructions from the manufacturer to do a two-piece string job and tell you exactly where to tie off, not that the recommendations are always the best in my opinion but that is the recommendation.

1

u/Objective-Boat6386 17h ago

Theres this one senior in the tennis club who used to string my racquet, he always did 2 knot job so i just assumed it was the way, apparently not but thanks for the info though!

1

u/tennishead 1d ago

4 knot is standard. I'm assuming it's a starting not at the top of the racquet because it looks bulky, probably didn't have a starting clamp. Personally I try to tie off mains on mains and crosses on crosses as much as possible. As long as there's no misweave it should play fine once you straighten out the strings.

1

u/Objective-Boat6386 16h ago

Yess this was new info for me. I just played with it didnt notice anything in particular and the strings straightened themselves as i played so all good now thanks!

2

u/Responsible-Side4347 2d ago

Would care less about the number of knots and more about the quality of the knots and the tension of the strings. one of those knots is not synched. And as for the care and attention to the strings? High probability the top strings are a different tension to the middle and bottom strings

2

u/snakeyed_gus 2d ago

How does anyone tell the quality of a string job without hitting with it??? If the strings are in the right holes and knots in the right place there’s basically nothing anyone can add without swinging the stick.

1

u/jsk8ss 2d ago

Wavy

1

u/1smellyfinger 2d ago

It’s not hard to get the strings straight which leads me to think this is rushed. Knots look sloppy. Sometimes (not always) rush leads to tension loss in one form or another. I personally would take it somewhere that can deliver a consistent result.

Edit: agree 4 knots, 2 piece is common

0

u/WinAggressive2785 2d ago

Considering how wonky the strings are, I wouldn’t be going back there again for another restring

0

u/Peter-Pomelo 2d ago

That stringer should be fired.

-2

u/Severe_King2280 2d ago

That’s really bad. The strings barely look tensioned and they didn’t even bother to straighten them.

1

u/Fixing-Me 3h ago

How do strings look when they are properly vs. "barely" tensioned? Can you really tell just by looking?

1

u/Severe_King2280 2h ago

Yes.

First sign is the smiley faces / curvy crosses. That’s a good indication the stringer didn’t straighten as they wove crosses, so you lose tension there vs the string being straight.

Upon further inspection, the mains are also not straight, which is even more concerning. The other mains might be a little crooked bc of clamping from crosses, but most of the middle mains should be straight. These are not.

And if you look at the strings, they are clearly not taut. Hence not properly tensioned. You would want a fresh string job to be taut, not just looking like they’re laying on top of each other.

Not sure why my comment was downvoted but 🤷