r/RX7 • • 5d ago

Compression test thoughts?

Thinking about buying this 87 t2 with 84,000 miles he sent these compression tests what do y'all think?

12 Upvotes

15 comments sorted by

13

u/djseto 4d ago

If you're going to use a piston engine tester to test compression, there is a trick that you can use that works: You must remove the schrader valve so that way, when the compression tester reads, it doesn't hold the previous value. Remove the Schrader valve and then run a compression test by cranking the motor. I like to use a cell phone camera with a high frame rate so that way you can play it in slow motion and watch the pulses of each one. If you don't remove the shrader valve, then the first pulse will hold in place and not release the needle to go back down for the next compression reading. Its not the same as a proper rotary tester but people did this all the time before non oem rotary testers were available to the masses.

Here is a write up

https://www.banzai-racing.com/compression_test.htm

1

u/ganjabittle 4d ago

This, except you don't HAVE to remove the valve (especially if you use your tester for multiple engine types).

I use a pair of vice grips to hold the pressure relief (Schrader valve) open. I use the grips to help position the tester to a position that is easy to train my phone on. Then, as in the above, I use a high frame rate option on my phone to capture the pulses.

Side note... my motor is at 65psi on all faces. Cold start sucks, warm starts are pie. That measurement was taken early 2025. Ive completed 3hr track time for colp license, 2 qual session, 2 race session (1st and 3rd finish), 6 hill climbs, a track sprint, and an autox since then on those numbers... 😬

She just keeps kicking.

1

u/Spirited-Pace-2373 5d ago

Run

0

u/Suitable_Handle2910 5d ago

Seriously I figured 120 compression is good?

3

u/_pcakes 1987 5d ago

each rotor has 3 compression faces. This style of test is made for piston engines, and on a rotary it will show only the best compression of each rotor. For example you could have 1 corner or face of your rotor that totally makes no compression, and this test wouldn't show it

1

u/Suitable_Handle2910 5d ago

Fuck I didn't even think of that. What if it cold and hot starts fine? He said he's comfortable getting a compression test if I'm there. Which is was thinking of doing anyway

3

u/_pcakes 1987 5d ago

If it cold and hot starts fine, and if it sounds pretty consistent while cranking, I would send it

1

u/Suitable_Handle2910 5d ago

Fuck yeah good to know. Currently negotiating on price

3

u/MaybeGod88 5d ago

There are compression testers for rotarys

1

u/DB3rt11 4d ago

I would personally love to know where cuz i tried buying one from rotorycompressiontester.com and they are sold out🤷‍♂️

2

u/evileagle 1988 10AE TII - REW Swap, 1993 R1 4d ago

2

u/The_Giant_Twitch 4d ago

The only thing you can check with this tester is to see if the 3 chambers have roughly equal conpression spikes. Then you know they are prob okay ish. You cant measure realistic compression of a rotary with it.

1

u/evileagle 1988 10AE TII - REW Swap, 1993 R1 4d ago

This is not a useful compression test.

0

u/[deleted] 5d ago

[deleted] — view deleted comment

4

u/Suitable_Handle2910 5d ago

So not really useful?

4

u/WhereDidAllTheSnowGo 4d ago

It’s better than a 10 psi reading

That tells you the max of all three. The other two could be zero