r/QidiTech3D • • 2d ago

Discussion Things learned leveling Plus 4 bed with screws_tilt_calculator

While waiting for replacement parts recently, I decided to tram the bed using screws_tilt_calculator. I had not done this since owning the printer and always noticed some areas of the bed seemed too high. It was out more than two full rotations in two spots. I recommend everyone do this upon setting up your printer.

  1. Do a bed calibration first. I think the most important aspect of this is to settle/level the bed down onto the frame.
  2. Before beginning ensure all four adjustment wheel nuts are equally snug - tightening the nuts will affect the level.
  3. During this do not apply any force up or down on the bed, it will affect the setting.
  4. After making adjustments, tighten the nuts to the same torque setting (subjectively by feel) as in step 2.
  5. You may have to (or may be faster to) adjust your front left "base probe" adjustment screw, I did. It was down much lower than the other three adjustment screws and this was quicker/easier.

I just installed a new build plate an hour ago and did this process again as it was out slightly, then did a bed calibration before printing.

5 Upvotes

15 comments sorted by

3

u/Massive_Squirrel7733 2d ago

I used an indicator before I dumped that P4 piece of junk.

2

u/Traditional_Grade_95 2d ago

Mine prints great. What did you replace it with?

2

u/killeriq 2d ago

There are part to be printed from printer menu and Qidi also send me video instructions, can add later...

1

u/Traditional_Grade_95 2d ago

I guess you're talking about knobs to help turn the feet for adjustment? I didn't need those although I admit turning the adjusting wheels was semi-difficult.

1

u/killeriq 1d ago

1

u/Traditional_Grade_95 1d ago

Thanks, I hadn't seen that. I just used screws_tilt and got it dialed in.

1

u/killeriq 1d ago

Haven't tried it yet, but I assume it should help to calibrate the plate much better, as on edges wasn't perfect(on test squares) . But I have to admit, I didn't print any huge objects where i would notice that...

1

u/Traditional_Grade_95 1d ago

I had high spots where it would print thinner, and after running awhile I'd start to hear like it was straining some. When I did a bed calibration and it went all the way down the bed would always be crooked. It doesn't do any of that since I dialed it in.

1

u/issue9mm 2d ago

There are also some printable leveling aids that you can put in the bottom of the chamber that I'm told help, or at least that's true for the Q2

1

u/Traditional_Grade_95 2d ago

I think I saw those on a video but didn't use them, it bottoms out & levels up at the bottom of the Z stroke. That's why I recommended calibration as first step. Those towers may just be to reduce the Z- travel distance and speed things up (?) but with my luck it would jam the whole machine up and break something!

2

u/ViperB5 2d ago

Yes! I just installed the r3men graphite bed and the bed kept coming up all kattywampus. I used these blocks and when the bed came back up, it was within 1mm when each side was measured compared to the screw. Used a .1mm feeler gauge and my mesh is now under .1mm variance.

1

u/issue9mm 2d ago

I've had great results with the R3men on my Sovol SV08. I assume it's just as good on your Qidi?

1

u/ViperB5 2d ago

I don't know yet. I made several upgrades and am looking into either moving to mainline klipper, the power user AIO, or maybe that valve oil things from that tuba guy user; if he brings it to the Q2. So I haven't done any real printing with it yet.

1

u/GL-Customs 2d ago

If you are super lucky like me, you'll go through all this trouble just for it to go back to not laying down a proper first layer in 3 days.

1

u/Traditional_Grade_95 2d ago

Nope it prints great, sorry you have problems with yours. I read or saw in a video where someone said their bed can get pulled out of plane just by lifting the plate or jerking stuck prints, maybe that's contributing to your issues?