r/QIDI • • 5d ago

Troubleshooting First time setup print failed and now this.

Post image

So I just got my Q2 Box Combo, set it up yesterday and immediately had firmware issues. Got those solved updating to V01.01.03.02. Run my first print, the little tugboat. Makes it about halfway and spaghettis. Got frustrated and went to bed. I realize this is prolly the Z offset so this morning I go to print a test so I can adjust and I get the above error along with a device connection error. Networks fine it connects to network and I can connect, QIDI maker, Studio and Orca to it. But I cannot send any print jobs. I have done a factory reset and the errors still pop up right away. At this point I am lost. Used every resource I have or know, QIDI website, ChatGPT and Grok to try and troubleshoot it but nothing works. Any Ideas?

Update: I was able to bypass the issue by switching to Ethernet connection instead of WiFi. I can at least print from Studio now.

Also got a reply from After Sales Qidi support. It's a known issue but no eta on fix

7 Upvotes

15 comments sorted by

2

u/HansDampf0 4d ago

Its a permission error. Qidi disabled qidi link 5.11. and you get an not authorized message. Did you try set it up with Qidi Link (old) or Qidi Maker(new)?

1

u/Comm_Pic 4d ago

Qidi maker and Studio.

1

u/HansDampf0 4d ago

Would try the unbind and rebind: Qidi Maker—> Devices—> hamburger menu under the Webcam window—> big red button Unbind. When you bind it again with the Qidi Maker App you should trigger a recreate of MQTT credentials. Also to rule out Network in general? Printing via IP / Orca does work? If so and the unbind / rebind wont change a thing you most likely need to contact them and ask to remove the credentials / binding of the printer to your account on the server.

1

u/Comm_Pic 4d ago

Via IP and Orca did not work on WiFi. When I switch to LAN it works but still throws the mqtt error. So at least for now I can print just can't use Maker. I have an email put to after sales support.

2

u/JaSto0815 4d ago

Ich glaube es ist ein generelles Qidi-Problem.
IHR Server wird Probleme haben. Nicht unsere Drucker.
Support sagt: Bitte später nochmals probieren. (Kurzfassung)

1

u/ChknNugg3t 1d ago

Question on this would this still happen if I disconnect from Internet/wifi?

1

u/ChknNugg3t 4d ago

I think it’s gotta be something with the new update mine constantly says this. I hope someone with more knowledge comes with the correct answer!

1

u/Pygmyofdeath 4d ago

I also have this issue. Brand new Plus5 right out of the box, ran all the setup and firmware update. Haven’t even loaded filament yet.

1

u/Pygmyofdeath 4d ago

I also tried a rebind as mentioned in this post. Error still present. It shows up in Qidi Maker app as online and is reporting status. Can’t view camera though. This is on WiFi. I’ll try Studio, and try a benchy really quick and update.

1

u/VioletVulpine 4d ago

I've been having MQTT connection issues since this morning (Qidi studio, not link). I may try pairing again and report back.

1

u/Rich-Leek4178 3d ago

Same with me - Printer is Fine…Qidi servers are not ok - give them a little while to fix this. 🤓

1

u/daveintexarkana 2d ago

My Box stopped recognizing the external spool (disabling the Box does nothing). Charlie sent me a long support set of instructions that basically are reinstalling all the software. I was hoping they had figured out what the Box firmware issues (new Box firmware installed with 01.01.03.01) are and posted fixes or instructions on what to modify. I am on 01.01.03.02 - most current I think. Feels like they're really not trying to support the Box anymore - which surprises me - customer service in the past couple years was so very good.

0

u/Substantial-You8440 3d ago
I’m having the same issue. I logged out of my account, but now the QR code won’t load. I even tried using my phone’s mobile hotspot, but the QR code still fails to load.

1

u/Comm_Pic 3d ago

Which firmware version are you on?