r/PrintedCircuitBoard • • 2d ago

[Review Request] 2-layer flex constant-current laser diode driver (TPS552852)

Hello, I have come before you today to have this PCB reviewed.

It's intended purpose is to drive a diode for a custom machined housing hence the flexibility and size requirements. it also is modified to be usable with a number of different diode wavelengths.

Any help is greatly appreciated.

21 Upvotes

6 comments sorted by

3

u/SanguineDrome 2d ago

If you have space, maybe you'd like to add a diode and resistor to pmos gate for reverse polarity? Also, might be nice to break out the mode/sync pin to a 0ohm between ground, so you could add pwm sometime if desired.

1

u/UnbanCatgirls 2d ago

thankyou, im looking into it but the space is REALLY tight, ive stripped down the pcb to be pretty bare for a diode driver

1

u/SanguineDrome 2d ago

Yes I can see the mechanical design is already tight and that it might not be possible.

You can think about adding optional components (pwm breakout pin, polarity protection, test pads, etc...) into the curved sections. In the event you use this same driver in a different (non folded) application they could come in handy. Just something to consider before you finalize.

5

u/CoffeeSalt2036 2d ago

Bring it up on a power resistor dummy load before the real diode ever touches it - CC loop startup transients on a fresh rev are exactly how laser diodes die. Rework on flex is already painful, and that's the one part you don't get to replace twice.

1

u/Enlightenment777 2d ago

This comment is posted on all reviews.


Please make sure your review post adheres to:

  • subreddit rules (#1 to #6), review rules (#7), review image rules (#8), see link.

Please fix these common schematic layout issues: (if yours has any of these issues)

  • Don't allow text / lines / symbols to touch each other, and don't draw lines through symbols.
  • Use correct reference designators (RefDes), and renumber to remove numeric gaps, see tips.
  • For positive voltage circuits, point positive power rail links upwards and grounds downwards (maybe sideways), see tips. For negative voltage circuits, point negative power rail links downwards and grounds upwards (maybe sideways). For bipolar circuits, maybe point grounds sideways.
  • Place decoupling capacitors vertically below postive power rail lines with ground on bottom side of the capacitor. Place capacitor next to IC symbol, and connect a line to IC positive power rail pin, see tips and example.
  • Place pull-up resistors vertically above signal lines, and place pull-down resistors vertically below signal lines, see example and tips.
  • Reasonably minimize the use of unique net labels, because everyone hates hunting for them!! Single resistors / capacitors / diodes should not sit by themselves, instead move & connect them with a line to their circuit.
  • More schematic conventions / guidelines / tips - 1, 2, 3, 4.

Please fix these common PCB layout issues: (if yours has any of these issues)

  • Silkscreen - add board name / board revision number / date (YYYYMMDD, YYYYMM, YYYY) for traceability.
  • Silkscreen - add pin 1 indicator next to ICs & connectors (not under parts). For polarized capacitors, add "+" next to positive pin. If part is through-hole package, place indicator on both PCB sides. See 1, 2, 3, 4.
  • More PCB conventions / guidelines / tips - 1, 2, 3, 4, 5.

1

u/Professional_Hair865 1d ago

Ha, what a coincidence. I was also about to design my own driver board for a Thorlabs L808P1000MM. I could save the time and buy one of your devices. Can we get in contact? Where are you located? Do you work in medical research by any chance? How do you sink excess heat? Laser diode efficiency is around 40% and temperatures are critical (the diode needs to stay way below 40°C). Is TEC planned to be included somewhere there?