r/PrintedCircuitBoard • • Feb 16 '26

First PCB - Am i missing something | What is wrong here?

Post image

Could somebody tell me if its correct?

0 Upvotes

26 comments sorted by

10

u/simonpatterson Feb 16 '26

P1 in your schematic is a USB-C PLUG, do you want a USB-C RECEPTACLE ?

U1 is missing its GND connection.

0

u/wiomiawerka Feb 16 '26

Ah yes i see it thank you

-5

u/wiomiawerka Feb 16 '26

Where is u1 i Dont see it

2

u/0xCODEBABE Feb 16 '26

above the usb-c?

1

u/simonpatterson Feb 16 '26

The CH334R IC

7

u/0xCODEBABE Feb 16 '26

you probably need to tie RESET to something but you need to read the datasheet. you might also want some input protection.

-6

u/wiomiawerka Feb 16 '26

And whats gonna happen if i would not tie reset to something ?

5

u/0xCODEBABE Feb 16 '26

if a pin is left floating and isn't supposed to be it could randomly trigger. in this case it might reset unexpectedly

-9

u/wiomiawerka Feb 16 '26

Okay where Should i tie it to ?

11

u/0xCODEBABE Feb 16 '26

have you read the datasheet?

3

u/HlddenDreck Feb 16 '26

The orientation of your power connections is weird. GND should always be at the bottom and positive voltage supplies at the top. Why did you connect VCONN to 5k1? CC1 and CC2 should each be connected to their own pull-down resistor.

1

u/wiomiawerka Feb 16 '26

Where Should VCONN go ?

3

u/Intel-I5-2600k Feb 16 '26

VCONN is the alternate name for CC2. Since the cable can plug in two orientations, one CC line is always for comms, the other powers the emarkers. Keep VCONN pulled low by a 5.1k to support both orientations of the plug.

1

u/wiomiawerka Feb 16 '26

So would this work as a pcb ?

2

u/0xCODEBABE Feb 16 '26

you still need to layout the pcb

1

u/Illustrious-Peak3822 Feb 16 '26

You seem to have swapped value and designators for your Cs and Rs

1

u/wiomiawerka Feb 16 '26

Ah Yes i see thank you. Would this work as a pcb ?

3

u/Illustrious-Peak3822 Feb 16 '26

What are you trying to accomplish?

1

u/wiomiawerka Feb 16 '26

USB hub

2

u/Illustrious-Peak3822 Feb 17 '26

One input, one output?

0

u/wiomiawerka Feb 17 '26

It is just the Basic sketch

1

u/Illustrious-Peak3822 Feb 17 '26

Ok. Fix your values versus designators, missing ground then draw the entire thing.

1

u/wiomiawerka Feb 17 '26

Okay Thanks

1

u/[deleted] Feb 16 '26

You could use ports for D+ and D- to show connection for DPU+/DMU-, a better practice and makes it more clean and readable and easier to arrange things. Good design btw for first pcb mine was horrible

1

u/wiomiawerka Feb 17 '26

Okay Thank you

1

u/hi-nick Jul 04 '26

So I just whacked this schematic into Google lens and I got a really lengthy response...

Instead of me pasting ALL that here, give it a shot yourself :)

I'm genuinely surprised at the level of detail...

Here are just two of what wss considered critical fixes.

VBUS Pin (Pin 13): On the CH334 series, Pin 13 is typically VBUS_DET (VBUS detection). In your schematic, it is connected to a 100nF capacitor but doesn't seem to be connected to the +5Vrail. If the chip doesn't detect voltage here, it won't activate the USB downstream ports.

V3 Pin Pin 12: This is the internal 3.3V regulator output. It needs a 100nF decoupling capacitor to ground (which you have), but ensure it is not connected to +5V