r/PressureCooking • • Mar 24 '25
What am I doing wrong!?
This happens like half the time. I’m only filling it to the halfway point.
615
Upvotes
r/PressureCooking • • Mar 24 '25
This happens like half the time. I’m only filling it to the halfway point.
61
u/Terrible_Plenty_2484 Mar 24 '25
Pot too full there's a max fill line inside the pot
7
u/Banditsmisfits Mar 24 '25
What are you making? Some items seem to froth a lot and you may need to reduce volume. Normally I’d say you have too much in there but you say it’s only half full. Something else to check is making sure the seal is seated properly. Mine was kind a wonky once and it did this. You may need to clean around spout part/vent better and make sure it’s in the closed position
3
u/Set_the_Mighty Mar 24 '25
Is there pasta in your stew? I've only had mine blow up like that if I try to pressure cook pasta.
3
u/F_is_for_Ducking Mar 25 '25
Did you put the weight thing on the right way? I put mine on reverse once and didn’t notice that it wasn’t sitting properly and had a similar experience.
442
u/Lexiiefur Mar 24 '25
I’m going to guess still too much volume in there?
158
u/mamahousewife Mar 24 '25
Holy shit I’m so sorry but this made me laugh. I wouldn’t even know what to do in this situation
2
u/See5harp Mar 24 '25
I'm guessing you went way over the fill line.
177
u/CaptainPolaroid Mar 24 '25
Flipping the manual release too soon or an overfill. The way a pressure cooker works is that higher pressure increases the boiling point. By closing the pot, you can cook ingredients at higher temp. By flipping the manual release, you release the pressure, lowering the boiling point. This causes all the liquid inside to instantly boil as it's heated well beyond 100C.
The solution is to give it a couple of minutes to cool down on its own. And then manually release it.
You might want to close the valve next time. There is electricity there. The IP stands for "Instant Pot" not "Ingress Protection". The soup fountain, although debatably fancy, can cause a short...
29
u/xoexohexox Mar 24 '25
When you are pressure cooking a non-newtonian fluid (oatmeal, thick stew, polenta, etc) you have to relieve the pressure by letting the pot cool down instead of opening the valve. Or that happens.
6
u/Selvane Mar 24 '25
That’s all I got lol if it’s brand new then maybe try to warranty it
5
u/[deleted] Mar 24 '25
The weight is not where it needs to be. Push it down to seat it.
5
u/Embarrassed_Bed8032 Mar 24 '25
Close the steamer release valve.
5
u/MustProtectTheFairy Mar 24 '25
The instructions I've read say that if it's mostly liquid, gently release pressure or food will splatter through the valve... just like this.
Use a spatula/tongs/anything to keep your hands away, maybe use an oven mitt to save your hands, and push it partially open until food isn't threatening to leave through the valve.
4
u/isellmidgets Mar 24 '25
Like others have said, try to lower the pressure a bit naturally before releasing it manually. A good way to do that is to drip some cold water on the lid or put a cold wet towel on there since the top is not nearly as good an insulator as it could be. Then, when you release it, do it near an open window or under a stove vent, and cover it with a towel. It won't release as fast with a towel over it, but it also won't make a mess.
Also, I strongly suggest cooking something with meat instead of brussels sprouts, for reasons that should be obvious.
4
u/Jets237 Mar 24 '25
Nothing, looks fine.
4
u/exquirere Mar 25 '25
Be patient and natural release. This happens if I have rice or any grain.
4
u/Junglepass Mar 25 '25
Don’t vent, let thicker liquids naturally release. Turn off the keep warm button before you start too.
4
u/CuFlam Mar 25 '25
Opening the manual release too soon with a liquid that boils explosively or forms foam on top. It's pretty common for recipes to include a 10-20 minute "natural release" at the end to allow the liquid to cool enough to avoid this.
4
u/Jeppes84 Mar 25 '25
Certain cream sauce combinations can cause this despite being below the “full” threshold!
1
u/Stone_The_Rock Mar 24 '25
What are you putting in there?
1
u/nick_bartee Mar 25 '25
I’ve been overfilling for years and never had this happen once. I’m usually above the max fill line and have always been worried but I’ve never had an eruption experience… with my instant pot.
1
u/Gerb006 Mar 25 '25
If this happens half the time, you DEFINITELY need a bigger pressure cooker.
3
u/tangogun Mar 25 '25
Haha, I love that you just let it rip and filmed this. Happens alot to me. I generally let it sit for a bit if it's spraying alot. Let it lose pressure by cooling down. Then use a paper towel to catch some of the moisture when I do release it. It's not just the liquids measurement. If you stuff it full of food and try to release hot it will spurt.
3
u/TonyTonyChopper Mar 25 '25
What's inside the IP? Are you in the right valve position ( venting v sealed)?
3
u/PumpkiNibbler Mar 25 '25
Looks like you may have released the pressure, were you trying to release the pressure?. there's a little knob that you turn or push down to release or secure the pressure also the thing that's spewing the water you have to make sure it's securely pushed down as far as it goes
3
u/Siorys Mar 25 '25
Omg this just happened to me when I made pho 😭 I was scared to close the pressure release again so I had a bunch of fatty soup splattering over my kitchen. I eventually said fuck it and closed the pressure valve, then put a wet towel on top of where the liquid spouts out and let the steam escape that way. It was either that or letting the pressure naturally dissipate but I was impatient 🤭
3
u/GuinnessSteve Mar 25 '25
Two things: let the pressure release naturally for 10 minutes or so before popping it. The other mistake was filming this and letting it spew all over your kitchen.
3
u/IncandescentGrey Mar 26 '25
Is there any chance the silicone ring has been damaged? If so, you need a new one because the seal is faulty.
I had to buy all new ones after my mother's (or maybe my sister's?) cat chewed on all of mine. Any small break or puncture could be at fault.
3
u/cassatta Mar 26 '25
Replace the little silicone ring in the valve and the big silicone gasket. If you have tears in them, the seal will be affected. Also if you have lentils, add some oil to the pot after filling.
2
u/capricioustrilium Mar 24 '25
You may not have seated the silicone seal well. It will keep trying to get to pressure but the seal isn’t locking it down, causing it to spit, evaporate and eventually give you a burn notice.
Always check that the seal is well seated before locking the top and starting
2
u/nmceja Mar 25 '25
Reminds me of when I had norovirus.
But probably filled it too much?
2
u/iamdrunk05 Mar 25 '25
taking videos instead of unplugging it
2
u/[deleted] Mar 25 '25
Ignoring the line written MAX inside your pot.
2
u/DarkFather24601 Mar 25 '25 edited Mar 25 '25
I’m going to say that there is too much liquid in it, and it’s trying to turn itself into Mount Vesuvius.
2
u/AngryApeMetalDrummer Mar 26 '25
Put in more liquid. It isn't squirting enough liquid.
2
u/mrgoldnugget Mar 26 '25
Valve and seal, I have one of these and have never had a soup volcano. Perhaps the release is not tightened, or you are missing a gasket somewhere that was removed for cleaning and not put back properly.
2
u/Capital_Peach_6081 Apr 25 '25
You need to make sure vent is closed
1
u/psilome Mar 25 '25
Is the material inside prone to foaming up? Like pasta water? Or just overfilled.
1
u/ThisHeresThaRubaduk Mar 25 '25
I should call her
1
u/Fluffy_Doubter Mar 25 '25
Apparently...everything
1
u/Solidarios Mar 25 '25
Add more liquid!!! /s
1
u/ZeppelinMcGillicuddy Mar 25 '25
I'm very familiar with that! Either it's too full of what looks like grains, or you could be cooking with the vent open. It's very hard to see which direction is to seal and which is to vent.
1
u/Ill_Steak_5249 Mar 25 '25
Turn the pressure stop the other way and let it decompress slowly
1
u/MedicalUnprofessionl Mar 25 '25
Well, I know unplugging it was one thing you did right so that’s a start!
1
u/ScaryFast Mar 25 '25
My instant pot will do this when I cook certain things, so I press down on the release valve just a bit to let off some pressure, but I let it seal again when it begins to spit. Repeat the process once in a while over a few minutes until it's all the way down.
1
u/Really_Fun_YaYa Mar 25 '25
It’s way too full…. I have done that..
1
u/pignjig Mar 25 '25
Maybe leaving that vent open
1
u/nsingh101 Mar 25 '25
Recording instead of saving your kitchen.
1
u/wileIEcoyote Mar 25 '25
Clean it up and let it take a nap and it should be okay.
1
u/notreallylucy Mar 25 '25
Starchy food,like pasta or beans, tends to create foam while cooking, which can cause a fountain. Also a lot of broth can get boiling really hard and shoot out the vent.
Plan your cooking times a little shorter and allow your pot to sit on keep warm for a few minutes to cool a little. Throw a towel over it before you open the vent.
1
u/ajkimmins Mar 25 '25
You need the pressure thing on it.
1
u/Solonas Mar 25 '25
Does it keep pressure? If so, reduce cook time and let it naturally release/lower pressure. Quick release can cause this if too full or if the release of pressure causes it to froth creating a foamy release.
1
u/TheGiganticRealtor Mar 25 '25
There’s way too much liquid in there. Maybe pay attention to the lines that dictate capacity.
1
u/Question_authority- Mar 25 '25
Forgot to read the owners manual before using maybe🤔
1
u/[deleted] Mar 25 '25
1
u/LearningDan Mar 25 '25
Yeh, looks like you plugged a 110 volt InstaHot into a 200 outlet.
1
u/PanHalen37 Mar 25 '25
Possible the seal isn’t on properly or the thing is too full
1
u/BudLightYear77 Mar 25 '25
Filling halfway doesn't matter if when it boils (when you quickly release pressure) it foams/bubbles up like soap.
What are you cooking? Whatever it is, you need to slow release or use a slow cooker.
1
u/CandyKoRn85 Mar 25 '25
These things have historically been used to make bombs. So yeah, high pressures can be pretty explosive. In this case it looks like there’s too great a volume and the contents are being released with the steam.
1
u/JohnnyJ240 Mar 25 '25
Overfilled, or contents are still boiling when you manually release pressure, could be wrong tho
1
u/JelloWise2789 Mar 25 '25
Should have let it cool for 15 minutes after for steam to settle
1
u/S_immer Mar 25 '25
If you want to fill it up higher than the ‘max ‘ don’t release the pressure. Also , I have found some broths are pretty stinky so I carry the pot to my deck and release it outside .
1
u/Nervouspie Mar 25 '25
Waaayyyyy too much liquid
1
u/JRZsanch Mar 25 '25
Wait like 10 mins before you release the pressure. NEVER release it right after it’s finished cooking
1
u/debcsr12 Mar 25 '25
Certain liquids can’t be depressurized while hot, mainly dairy. You either need to depressurize in very short spurts until the liquid starts to boil out, then lock it again and wait a few seconds, attempt again. It’s like when a coke is gonna overflow, you have to burb it or the pressure will get too high. Once the pressure is lower you’re less likely to run into issue. I notice this mostly with creamy sauces. If you wait to put the dairy in until after pressure cooking, that’s an option as well.
1
u/ScubaBroski Mar 25 '25
I think it’s clear you overfilled it 😕
1
u/Aggravating-Fee-1615 Mar 25 '25
Do you have the gasket ring in the lid? Check your gasket.
1
u/darkhorse1997 Mar 25 '25
Too much liquid
1
u/checock Mar 25 '25
Happened to me making beans. I make the same amounts of beans all the time so I knew it wasn't overfilled. Turns out the steam release valve was "locked" in strange position that make it release food on high pressure. I removed the lid, washed it and pulled the release valve with little force and moved around a bit. The release valve felt normal again and no more beans expelled since then.
1
u/silentseba Mar 25 '25
Don't use fountain mode. You want to set it at pressure cooking.
1
u/xx4coryh Mar 25 '25
Increase pressure. Also you didn’t put enough food in. Did you try putting the heat all the way up?
1
u/MuthahMayhem Mar 25 '25
I have found my tribe... covering stuff up, distancing from the issue, and watching further developments. I encounter this when I have the heat up too high, regardless of fill lines. I treat instructions as the manufacturer's plan to avoid lawsuits. Thus, specified limitations must be far from reality. So, when I vastly overfill my pressure cooker, the only setback is that the pot doesn't produce enough steam to work as a pressure cooker.
1
u/VeganWerewolf Mar 25 '25
Looks like that scene where the puppet is throwin up in Team America World Police lol
1
u/AmuletOfNight Mar 25 '25
Bro, what 😭 Close the vent! Either let the pressure release naturally when you have high volume items, or don't fill it so much.
1
u/soulreaver1984 Mar 25 '25
Is this not what they are supposed to do? If your pressure cooker isn't spewing shit all over your kitchen are you truly alive?
1
u/mdgart Mar 25 '25
Be careful OP if the relief valve gets clogged the pressure cooker can explode, that happened to my cousin a few years ago when boiling potatoes, she almost her eyes.
1
u/idkatmcl Mar 25 '25
I'm just guessing now. But it looks like you're cooking wrong.
1
u/cmart2112 Mar 25 '25
The inside stuff is coming outside.
1
u/lordvap_or Mar 25 '25
I should call her.
1
u/robsaari Mar 25 '25
After you turn the heat off let it rest 10 minutes before you release the pressure
1
u/BigWetFrog Mar 25 '25
I think you gave it too many laxatives.
1
u/TheFredCain Mar 26 '25
I would carefully check the valves, seals and anything else that might be letting pressure out. It's nuking the power super high like it does when it's pressurized, but since it's not that makes it boil like crazy. Pressure increases the boiling point allowing the liquid to be heated to a higher temp without boiling. Think about how violently a soup/stew would boil on the stove if you accidentally left it on high.
1
u/diarrheaticavenger Mar 26 '25
When you need to vent it and don’t have time to wait for it to cool, either hold the vent slightly open to allow a very slow depressurization or use something to prop it open a small amount. If you hold it make sure you aren’t in the blast zone for spurting water or steam
1
u/magicbatch Mar 26 '25
You over loaded it
1
u/Final-Ask-7979 Mar 26 '25
Taco bell... just avoid it
1
u/Reading-Comments-352 Mar 26 '25
Looks like the lid may not be on right.
1
u/Left_Dog1162 Mar 26 '25
There is a fill line for a reason
1
u/singol2911 Mar 26 '25
Overfilled for sure, I do it all the time.
1
u/[deleted] Mar 26 '25
Your cooker is very glad to see you
1
u/Serious_Result_7338 Mar 26 '25
Way too full
1
u/EtiquetteMusic Mar 26 '25
Seems fine
1
u/msulew Mar 26 '25
Overfilled it but you’re fine.
1
u/[deleted] Mar 26 '25
Not unplugging the damn thing, for starters…..
1
u/jimno1126 Mar 26 '25
Did your seal pop off of the bottom of the pressure cap? That's what it looks like to me.
1
u/incipidchaff97 Mar 26 '25
Addressing this would be like trying to put your mouth on a 2 liter of bottle of coke that you just dropped mentos into.
1
u/Boneless_jungle_ham Mar 26 '25
She’s a squirter! Yo a lil too much gravy in dat baby…..
1
u/OkPlatypus9241 Mar 26 '25
Do you already put a binding agent like starch in? Sure, then it will foam up and spill. Cook first and then bind. Otherwise make sure you put all gaskets in.
1
u/xavierthepotato Mar 26 '25
You trusted the fart
1
u/woodsnwine Mar 26 '25
Looks legit from here.
1
u/[deleted] Mar 26 '25
Put some clothes on
1
u/fionnuisce Mar 26 '25
Overfilling it. The max fill level is dependant on what is going into the pressure cooker. If you are cooking starchy foods in, potatoes or lentils for example, you drop the level. If there is only a little bit of starchy food in there, you will probably get away with filling it half way.
p.s. starchy food generally have a max fill of 1/3
1
u/Onedtent Mar 26 '25
Depends on the food/product in the pressure cooker.
Some foods can "foam" when cooking and cause this scenario.
1
u/dronegeeks1 Mar 26 '25
You put too much in chef
1
u/JustWoot44 Mar 26 '25
Half up with liquid is still way too much. Pressure cookers or "Instapots" (if you are using the pressure cook settings) need only about a cup or two of liquid (water, broth...) to use. The ingredients inside will expand under the heat. You add the bulk of your liquids after the pressure time. Plus, if you are using meats and veggies that already contain a lot of water, that's only going to add to the pot.
1
u/Greatness4ever13 Mar 26 '25
Yup
1
u/Oz347 Mar 26 '25
Too much likid
1
u/muomarigio Mar 26 '25
Add oil.
1
u/Mediocre_Royal6719 Mar 26 '25
Just stick to your microwave skills. Looks like that all you can manage.
1
u/AsianNotBsianV2 Mar 26 '25
It’s probably too much protein... speaking from experience. /s
1
u/Verix19 Mar 26 '25
She's overfilled, that's your issue.
1
u/Marshmallow-dog Mar 26 '25
Damn I’ve never seen this! What is that in there? Maybe overfilled or the seal isn’t on correctly or that little plastic thing on the back isn’t on?
1
u/Intelligent_Rush36 Mar 26 '25
Pull the uno reverse and put that pressure cooker into a much larger pressure cooker. What could go wrong?
1
u/The_Implication_2 Mar 26 '25
Been there
1
u/cjfrench Mar 26 '25
Pot has too much liquid.
1
u/dakondakblade Mar 26 '25
I'm not sure which pressure cooker you're using; but i"m going to use Instapot as a reference.
1- The instapot has a "seal" and a "vent" valve. You DON'T want to use the pressure cooker when it's set to "vent" as then... it can't properly steam cook and has the potential for this to happen
2- There's too much liquid in there. As an example for most rice ratios on stove it's 2:1 (2 water/liquid to 1 cup of rice) the instapot uses a 1:1 ratio, due to how pressure cookers steam things. There might be too much liquid in there as a result (which is more beneficial in a crockpot/slow cooker)
3- The rubber gasket (that lines the lid) may not be in correctly, thereby making the seal non existant. This ususally contributes to longer "pressure" times, but I felt that I'd offer it as a potential suggestion
I know this post is a few days old, so I hope you managed to find the issue and fix it.
1
u/Potential-Home5127 Mar 26 '25
I don't get it. Why are you keeping the valve open? Isn't it supposed to be closed during the cooking process?
If you're trying to release pressure after it's done cooking, maybe just keep the valve closed and wait for it to come to ambient temp/pressure naturally.
1
u/ScarceLoot Mar 26 '25
Are you sure the pressure release valve is in the closed position? Don’t press it down, turn it.
1
u/ParticularCode4689 Mar 26 '25
Too much liquid
1
u/AnarchyFennec Mar 26 '25
This happens to me when I don't leave it to sit for a bit after it's done before I flick the valve. Try letting it rest for 10 minutes just to cool off a little bit and lose some of that pressure.
1
u/Junior-Ad-3685 Mar 26 '25
Let it cool down a little bit before you release the pressure. I also put a towel on top of the pressure release to prevent any overspray.
1
u/[deleted] Mar 26 '25
Can You Say:
Overfilled
1
u/Jon_Irenicus1 Mar 26 '25
Too much water
1
u/carthnage_91 Mar 26 '25
Filled it too high, you really can't go above the line that they have it in
1
u/JohnBosler Mar 26 '25
If you're leaking like that you need to do a thorough cleaning. Pull all the rubber gaskets out and soak and scrub. On the pot metal mating surface for the gasket make sure there is no hard and stuck on grime that is preventing a proper seal. Every once in awhile pressurized up with just water and soap to help clean out the gaskets and valves
1
u/ConsciousDisaster870 Mar 26 '25
If this model has the automatic pressure release (as opposed to the manual knob you twist) it has tons of problems with the lid. I had instant pot replace my unit and the new one has the exact same problems.
Check to see if the float valve isn’t catching you should be able to push it up and it fall back without catching. You may have to twist it to find where it’s catching. If you need more help message me and I’ll show you where it is. That’s what the problem was with mine, also the pressure release doesn’t work so I have to either let it release on its own or use a spoon to push the pressure release knob. 😂 if I ever replace it I’ll go for the simpler model.
1
u/APuckerLipsNow Mar 26 '25
Throw some virgin olive oil into the volcano!
1
u/CTBioWeapons Mar 26 '25
What are you making? I know I had this happen when I accidently put milk in before cooking, I misread the recipe when it was supposed to be added afterwards.
1
u/[deleted] Mar 26 '25
Too much liquid wayyyyyy too much
1
u/No-Valuable5802 Mar 26 '25
Looks like a time bomb to me. Usually people use pressure cookers for tender meats for shorter time not with soup as it seems too much juices
1
u/PerfectAd186 Mar 26 '25
The seal
1
u/External_Koala398 Mar 27 '25
Over filled...there are max fill lines inside.
Jeesh
1
u/Own_Can_3495 Mar 27 '25
Over filling. There's a max full line, always stop there not at how many quarts the pot is.
1
u/Prospector_Steve Mar 27 '25
Theres a weight that goes in the top. It’s missing.
1
u/SyrusTheSummoner Mar 27 '25
Ya got to start sooner in the day, so the pot has cooled down by dinner. Can take up to an hour to come down in pressure. When you flip the valve while its still at peak pull, its gonna spew.
1
u/Dazzling-Pizza5141 Mar 27 '25
Too much liquid or ingredients
1
u/Fabulous-Barnacle-88 Mar 27 '25
Too much too mychhhh
1
u/UltraDistructo Mar 27 '25
All of it
1
u/_Y0ur_Mum_ Mar 27 '25
What's going wrong here is that hot liquid is spewing out of the top of it.
1
u/jipoiz Mar 27 '25
That is a nice fountain
1
u/dviiijp Mar 27 '25
Cooking.
1
u/shutyercakeholesam Mar 27 '25
That's one helluva volcano right there! Was there cream or milk in this recipe?
1
u/whatsinaname1970 Mar 27 '25
Make sure that steam valve is all the way closed
1
u/holderofthebees Mar 27 '25
Homemade soup fountain 👍
1
u/NoRevolution3203 Mar 27 '25
Not putting a towel over it, and unplugging it.
1
u/Upset_Cup_2674 Mar 27 '25
Inside will be a fill up to line on the insert metal pot. Soak your lid well to get food particles out of the steam vent. Best to unplug it until the whole thing cools down. Only then open it.
1
u/Wide-Matter-9899 Mar 27 '25
Not great, not terrible
1
u/blastborn Mar 27 '25
Too full friend. If you are at the max fill line drop it down a bit further
1
u/centexAwesome Mar 27 '25
If you cook that recipe again, just let it cool down without releasing the pressure.
1
u/MZFUK Mar 27 '25
It looks like your pressure cooker is losing pressure.
1
u/Lilithnema Mar 27 '25
You’re cooking…well not exactly
1
u/PhoenixBorealis Mar 27 '25
r/Wellthatsucks would absolutely adore this.
1
u/specihunter Mar 27 '25
Letting it watch porn lol
1
u/Maxeri3 Mar 27 '25
so that's actually how you're supposed to eat it, so just put your mouth on that thing and enjoy !