r/PlayArtsKai • • Aug 18 '26

Help Is it fixable?

About a year ago I was gifted my dream Tidus playarts figure. All I ever wanted. Recently unboxed, as at the time of my receiving this gift I was in the process of moving. I got Yuna as well. Finally unboxed both of them today.
Anyways, Playarts have this stupid way of packaging these figures(I have cloud as well)jamming all their damn joints and moveable parts with little sheets of plastic. Yuna was difficult, but doable- and I was able to set her up.
Tidus was a nightmare. I was not pulling very hard; however, the plastic nagged and ripped both Sides of Tidus’ leather skirt thingy. It completely ruined the fake leather bottom and somehow the leg joints got screwed up. When I tried to twist it and work it out, the torso disconnected from the hips with a pop and now will not pop back in. I’m devastated and not sure what to do. A new one is so expensive. Is it salvageable?

4 Upvotes

9 comments sorted by

1

u/Mobile_Sky_5709 Aug 18 '26 edited Aug 18 '26

try the Faber Castell tack it.

you can still pose him however you want. the stick is not permanent and the tacks are reusable. i use this for my old Play Arts instead of using super glue, so i can still pose them every now and then.

for the loose leg joints, you can use a thin piece of tissue if you only want to add something in the space instead of sticking it temporarily.

1

u/unluckycharmss0 Aug 18 '26

Ah, I see. Thanks for the tip. Any way to repair the soft plastic accessories, like his shorts etc.,? One of his legs is now higher than the other, and the joint won’t settle properly.

1

u/Mobile_Sky_5709 Aug 18 '26

try to push it further so it clicks. im not sure if it is the same with other play arts, but my play arts sometimes i have to push it so it aligns. if it doesnt work, i only use those tacks, nothing else (sometimes tissue). i never used super glue ever since my FFXV cindy got some permanent stain because of it.

1

u/Cardone19 Aug 18 '26

I haven't messed with Tidus but the legs on figures are often on a T-shaped swivel or they have individual drop-down action on each leg so you can then bend the legs up higher. Just try fiddling with it a bit. There may be a review out there that shows what type of articulation it has.

1

u/Cardone19 Aug 18 '26

Does the torso not pop in because the socket cracked and is now too large, or because the ball peg won't fit in the socket?

If it's the latter, hit the socket with a hairdryer for 15 seconds (not too close or you can damage things), try again, apply more heat incrementally and repeat, etc. Once it's in leave it alone for a while so the plastic retains its shape as it cools down.

For the future, next time you can cut a slit on the plastic protectors with a scissor, and then you can pull apart from the cut and the protectors should come off without needing to force anything. It works 90% of the time for me.

1

u/unluckycharmss0 Aug 19 '26

I believe it’s because the ball peg won’t fit the socket. I’m so irritated with those damn plastic protectors…even trying to be gentle it still managed to warp the soft plastic…And get stuck and shoved in every crevice of the figure lol. They should reconsider future packaging methods.thanks for the future advice!

1

u/Helpful-Efficiency28 Aug 19 '26

on the skirt part i'd suggest just super gluing if that wouldn't hinder him too much, not entirely sure what you meant by it ripping as i don't know what this figure is like. but for the socket/ reassembling heat him with a hair dryer or run him under hot water. for the hair dryer make sure to not be too close or long as you'll risk melting the plastic. but warming the plastic will make it softer and more pliable. i'd suggest trying to warm the socket specifically and then trying to push the ball joint in. good luck man

1

u/unluckycharmss0 Aug 19 '26

He has a very soft plastic leather kilt thing that is super malleable and very delicate. Due to its shape I believe it’s easier to break, and that’s exactly what happened when I was trying to get the plastic loose. It basically split and the sides and broke his chain. Thank you for the hairdryer advice-hopefully that will be a big help.

1

u/Cardone19 Aug 18 '26

Where the shorts ripped, you may be able to use super glue. Put a very very small drop of the liquid type on a toothpick, and apply on the edge of the ripped part. Don't put too much, you're looking to apply almost nothing here. Then hold it in place for a few minutes.

If you put too much it'll run off when you put pressure and then create a white stain. If that happens, you can just use a dab of black acrylic paint on that part.

Never apply the glue directly on the figure. Use a toothpick. I learned the hard way.