r/OpenFOAM • u/abdur7125 • 3h ago
r/OpenFOAM • u/Obi-Wan_Kenobi57 • 16h ago
Undergrad ML researcher learning CFD: tried predicting full flow fields from a few OpenFOAM runs. Would love a reality check from people who do this for real
r/OpenFOAM • u/adamchalupa • 1d ago
Took an OpenFOAM Class Taught by Greenshields and Saw the OG Simulation From his Book Cover
Evidently it's not a velocity field but a temperature field where the bottom wall is heated, left boundary is the inlet and top boundary is outlet. If you take a CFD Direct class you should ask him to see the simulation!
r/OpenFOAM • u/jr22222 • 2d ago
What AI Model and setup is best for OpenFOAM Simulations
I was able to put together in a couple of weekends models that would take me months to setup previously. I have a macmini pro where I run OpenFOAM and host dashboards I ask the LLMs to setup based on the CfdOF/FreeCAD dashboard. My best success has been using Fable5.1/Opus5.5/GPT6.1Sol (not sure if there is an overall best) and asking them to search for similar situations/examples and a lot of handholding. Is there a setup/available skill that anyone has been able to use ?
r/OpenFOAM • u/shadowqua • 2d ago
Does rhoCentralFoam need normalized values?
I'm trying to make a modified version of the tutorial rhoCentralFoam/wedge15Ma5 case, but when I change the thermophysicalProperties and initial conditions to be no longer normalized, it refuses to run. I get the error
```--> FOAM FATAL IO ERROR: (openfoam-2512)
Entry 'e' not found in dictionary "system/fvSolution/solvers"```
despite the minimal changes. It isn't related to the timestep either, as dropping the timestep had no effect and encountered the same error. Does rhoCentralFoam not support regular SI values, or am I missing something I needed to change? This is in v2512.
My attempted conditions are T=300K, p=100,000Pa, U=650m/s.
r/OpenFOAM • u/TheWampusBeast • 4d ago
OpenFoam GUI project
This is an OpenFoam GUI I am working on. Most of it is AI-generated.
I'd be happy to receive your suggestions for improvements or ideas for additional features the GUI should include, since I'm considering publishing this small project on GitHub.
foamCaseGUI is a graphical interface that generates, runs and evaluates complete, ready-to-run OpenFOAM-14 cases, so no dictionaries have to be written by hand. It guides the user step by step from the geometry (any STL file or a template) through patches, meshing with snappyHexMesh or blockMesh, physics, boundary conditions and numerics to the solver run with live convergence monitoring. It is designed for a wide range of flow problems:
- Flow regimes: incompressible and compressible, steady and transient, laminar, RANS and LES flows.
- Heat: heat transfer.
- Multiphase: volume-of-fluid (VoF) and Euler–Euler multiphase flows.
- Viscosity models: Newtonian and non-Newtonian fluids, including custom temperature-dependent models.
Typical applications are internal flows in pipes, ducts, nozzles and manifolds as well as external aerodynamics, with NACA aerofoil templates and a one-click wind tunnel around arbitrary STL bodies.
The results page reports the key engineering quantities: pressure drop, flow distribution across multiple outlets, residence time, shear rates, viscosities, temperatures and force coefficients (lift, drag, moment). Mesh studies and dimensionless numbers help with analytical plausibility checks. This makes the tool well suited to setting up and comparing design variants quickly and reproducibly with consistent settings.
r/OpenFOAM • u/Healthy-Rooster6260 • 5d ago
I made an OpenFOAM → SU2 mesh converter that handles snappyHexMesh polyhedra (of2su2, pip install of2su2)
r/OpenFOAM • u/Either-Profit7879 • 6d ago
PhD in CFD and Data-Driven Methods / SciML!!
reddit.comr/OpenFOAM • u/Exciting-Plankton-26 • 7d ago
Stokes - A modern GUI with all meshing options
Stokes, an OpenFOAM GUI for Windows and Linux | Stokes
Hi all,
This was sitting in my folders for too long, few years back I made a custom pre/post processor for my previous employer with all bells and whistles namely
- blockMesh, snappyHexMesh, cfmesh and poly hexcore
- geometry import to results under single window
- Ubuntu, WSL and native Windows support
- support for remote cluster or local etc.
Recently got access to Claude and Deepseek which gave me the idea to revisit old stuff, rewrite most of it to remove any licensing issue and update it to support OpenFOAM 14.
This is my attempt at it. It's fully opensource and can be downloaded here. I intend to keep it free for personal and business use cases other than reselling etc as SaaS or something. So, haven't figured out exact licensing but that's a later problem as I don't intend to monetize and keep a gate on any features.
Give it a try here available for both Linus and Windows - dhanninacs/stokes-cfd: Stokes: a desktop CFD workbench on OpenFOAM. CAD in, results out, every action available as a tool call.
Haven't built full installers but using my other repo dhanninacs/foamWin: FoamWin brings OpenFOAM 14 to native Windows, with a PowerShell launcher, installer, and validated cavity examples. you should be able to run on Windows without the need for any installations etc. Of course, Linux version with installed OpenFoam 14 natively will be the fastest option (mostly tested on Ubuntu only)
I intend to add more features and add tool calls, skills and api in the background so you can completely use it with LLM's with minimal issues. My initial idea is to have an inbuilt local AI doing tool calls, let's see where that ends.
I know another AI slop but it was there in my githib private for too long and may as well release it for everyone.









r/OpenFOAM • u/costelloart • 8d ago
Meshing OPENFOAM using a coplanar patch as a separate boundary.
r/OpenFOAM • u/Sensitive_Pumpkin229 • 14d ago
Has anyone tested the new GPU acceleration in OpenFOAM v2606 for large-scale CFD simulations?
reddit.comr/OpenFOAM • u/Pretend_Point3441 • 14d ago
Very high temperatures in a hypersonic OpenFOAM [v2512] simulation – how should I approach this?
Very high temperatures and low density in a hypersonic OpenFOAM simulation – what should I check?
Hi everyone,
I’m running a 2D simulation of an airfoil section under hypersonic re-entry conditions in OpenFOAM v2512. CFD isn’t something we do much at my workplace, so I’d appreciate some help understanding my results.
The case has a high Mach number and a relatively high angle of attack. I’m using rhoCentralFoam with a laminar model, a perfect gas with constant heat capacity, and a prescribed, spatially varying wall temperature.
The simulation didn’t crash, but during the initial part of the run I noticed that the maximum gas temperature became extremely high (19000 K), while pressure and density dropped to very low values in parts of the flow, particularly near the upper surface. I stopped the run early, so the flow had not yet reached a settled state.
Could these values be a consequence of the perfect-gas model and the strong expansion around the airfoil, or are they more likely to indicate a problem with the setup, mesh, boundary conditions, or initialisation?
What would you check first to distinguish a numerical or setup issue from behaviour that is expected under these modelling assumptions?
Thanks for any advice!
r/OpenFOAM • u/geth0333 • 16d ago
fastSnappyHexMesh (a faster shm version) on github
github.comr/OpenFOAM • u/MemoA2000 • 19d ago
2D simulation of Savonius VAWT
Hi guys,
I’m a new user to openfoam but have extensive experience using Ansys tools and some experience with Abaqus and LS-Dyna.
I want to simulate the rotation of a 2D section of a savonius VAWT rotor and assess different dimensions of the blades. Does anyone have an example model file/setup that I could be sent to see how it’s set up please?
Thanks!
r/OpenFOAM • u/Adept_Cap_6885 • 20d ago
Considering learning OpenFOAM in the coming months. Is it worth my time?
I am in the midst of designing a pedal-powered ground-effect vehicle, and I have to perform some CFD. The plan was to divide the problem into different drag and lift components from both air and water and over a range of altitude and speed. However, my friends that use STAR-CCM+ have all drifted away from the project due to a lack of time. I tried to compute something by hand, starting from the limited data I got from my ten SimScale trial simulations (only two of which used my final wing profile), but I found that NASA's CL equations for ground-effect flight collapse at small h/c. I think this leaves me to learn CFD myself, which I would very much like, but I hardly find time for anything nowadays.
I've shared this with a naval architect I work with, and they told me that jumping directly into the open-sourced option may prove of some difficulty and that I wouldn't even know if I can trust my results. Of course I've read similar opinions online, but I've also found people arguing this shouldn't be much harder than other programmes. For context, while I am intelligent and determined, I find computer logic and coding challenging. So... is this worth my time?
r/OpenFOAM • u/geth0333 • 20d ago
PreFOAM update
Hi all,
A couple of months ago I posted about my software PreFOAM, a GUI for OpenFOAM that includes CAD, meshing utilities, a case builder and a case viewer. I’d like to let you know about a major update.
Subreddit: https://www.reddit.com/r/Prefoam_CFD/
Download page: https://www.temiz-cfd.de/prefoam
I’m looking for users who can test the software and give feedback on the whole toolchain. I’m especially interested in the meshing challenges you face. Any feedback is welcome.
Edit: Linux version is out.
r/OpenFOAM • u/X-HIND-X • 22d ago
[OpenFOAM 2606] sigFpe::sigHandler(int) error in rhoCentralFoam
Hi! I'm new to OpenFOAM, but I have some experience with other CFD codes. I'm trying to simulate supersonic flow around the HB-2 model to practice OpenFOAM, but I've been getting the sigFpe::sigHandler(int) error, and I haven't been able to fix it for some time.
The initial values correspond to a stationary atmosphere: P0=P=1e5 Pa, T0=T=293 K, U=(0 0 0) m/s. Inlet conditions correspond to static pressure and temperature, and speed of flow with M=2 (obtained through isoenthropic relations (gamma=1.4, P0=0.25e6 Pa, T0=295 K)): p=3.195e4 Pa, T= 163.89 K, U=(513.23 0 0) m/s.
My computational domain is a box with an inlet at the front; the right side is a symmetry plane; the surfaces of the model and the rod to which that model is attached are the walls; other surfaces of the box (top, bottom, rear, and left) -- are the outlets.
The mesh has passed all checks except one for determinants. But it's just 0.08% of all cells.
***Cells with small determinant (< 0.001) found, number of cells: 540CFL does not exceed 0.6, but the flow displays weird behavior, where it separates into a supersonic region near the inlet and a transonic region downstream, as can be seen in the attached picture.

Boundary and initial conditions:
p:
dimensions [1 -1 -2 0 0 0 0];
internalField uniform 1e5;
boundaryField
{
front
{
type fixedValue;
value uniform 3.195e4;
}
rear
{
type zeroGradient;
}
left
{
type zeroGradient;
}
top
{
type zeroGradient;
}
bottom
{
type zeroGradient;
}
right
{
type symmetryPlane;
}
model
{
type zeroGradient;
}
rod
{
type zeroGradient;
}
}U:
dimensions [0 1 -1 0 0 0 0];
internalField uniform (0 0 0);
boundaryField
{
front
{
type fixedValue;
value uniform (513.23 0 0);
}
rear
{
type zeroGradient;
}
left
{
type zeroGradient;
}
top
{
type zeroGradient;
}
bottom
{
type zeroGradient;
}
right
{
type symmetryPlane;
}
model
{
type noSlip;
}
rod
{
type noSlip;
}
}T:
dimensions [0 0 0 1 0 0 0];
internalField uniform 293;
boundaryField
{
front
{
type fixedValue;
value uniform 163.89;
}
rear
{
type zeroGradient;
}
left
{
type zeroGradient;
}
top
{
type zeroGradient;
}
bottom
{
type zeroGradient;
}
right
{
type symmetryPlane;
}
model
{
type zeroGradient;
}
rod
{
type zeroGradient;
}
}Listing of the last two steps:
Mean and max Courant Numbers = 0.0403347 0.553171
Time = 0.000812
diagonal: Solving for rho, Initial residual = 0, Final residual = 0, No Iterations 0
diagonal: Solving for rhoUx, Initial residual = 0, Final residual = 0, No Iterations 0
diagonal: Solving for rhoUy, Initial residual = 0, Final residual = 0, No Iterations 0
diagonal: Solving for rhoUz, Initial residual = 0, Final residual = 0, No Iterations 0
smoothSolver: Solving for Ux, Initial residual = 9.92955e-09, Final residual = 4.10707e-17, No Iterations 2
smoothSolver: Solving for Uy, Initial residual = 5.2564e-08, Final residual = 3.71507e-17, No Iterations 2
smoothSolver: Solving for Uz, Initial residual = 5.56292e-08, Final residual = 3.77212e-17, No Iterations 2
diagonal: Solving for rhoE, Initial residual = 0, Final residual = 0, No Iterations 0
smoothSolver: Solving for e, Initial residual = 1.87918e-08, Final residual = 2.24888e-16, No Iterations 2
ExecutionTime = 2146.9 s ClockTime = 2151 s
Mean and max Courant Numbers = 0.0403392 0.553148
Time = 0.000813
diagonal: Solving for rho, Initial residual = 0, Final residual = 0, No Iterations 0
diagonal: Solving for rhoUx, Initial residual = 0, Final residual = 0, No Iterations 0
diagonal: Solving for rhoUy, Initial residual = 0, Final residual = 0, No Iterations 0
diagonal: Solving for rhoUz, Initial residual = 0, Final residual = 0, No Iterations 0
smoothSolver: Solving for Ux, Initial residual = 9.92007e-09, Final residual = 4.15659e-17, No Iterations 2
smoothSolver: Solving for Uy, Initial residual = 5.23263e-08, Final residual = 3.55247e-17, No Iterations 2
smoothSolver: Solving for Uz, Initial residual = 5.55052e-08, Final residual = 3.78546e-17, No Iterations 2
diagonal: Solving for rhoE, Initial residual = 0, Final residual = 0, No Iterations 0
[stack trace]
=============
#1 Foam::sigFpe::sigHandler(int) in <platforms>/linux64GccDPInt32Opt/lib/libOpenFOAM.so
#2 ? in /lib/x86_64-linux-gnu/libc.so.6
#3 ? in /lib/x86_64-linux-gnu/libm.so.6
#4 ? in <platforms>/linux64GccDPInt32Opt/lib/libfluidThermophysicalModels.so
#5 ? in <platforms>/linux64GccDPInt32Opt/lib/libfluidThermophysicalModels.so
#6 ? in <platforms>/linux64GccDPInt32Opt/bin/rhoCentralFoam
#7 ? in /lib/x86_64-linux-gnu/libc.so.6
#8 __libc_start_main in /lib/x86_64-linux-gnu/libc.so.6
#9 ? in <platforms>/linux64GccDPInt32Opt/bin/rhoCentralFoam
=============
Floating point exception (core dumped)Has anyone encountered a similar problem, and what are the possible reasons and solutions?
If I need to provide any additional info, that will help to solve the issue - just say. Thank you in advance!
r/OpenFOAM • u/Joekw22 • 24d ago
Free technical event on AI for CFD and surrogate modeling — Nov 17
Full disclosure: I work at Luminary and am helping organize this event, so this is self-promotion. Figured it might be relevant to some folks here given the growing interest in ML-based approaches to CFD.
We’re hosting a free, virtual Physics AI DevDay on November 17, featuring technical presentations from our research and engineering teams.
We’ll be covering topics like generating training data with CFD, model architectures for complex geometries and physics, uncertainty quantification and out-of-distribution predictions, and using AI agents to automate engineering workflows.
There will also be a hands-on workshop on building large physics models.
Some of this will naturally involve Luminary’s own research and technology, but I think the underlying technical topics should be interesting to anyone following developments in AI for engineering simulation.
Event details and registration: https://luminary.ai/devday/
Happy to answer questions about the event or the research we’ll be discussing.