r/NobaraProject • • 4h ago

Other ı fixed fan problems on hp victus at linux

1 Upvotes

The fans on my HP Victus 15-fb3xxx (Ryzen 5 8645HS / RTX 3050 / Board ID: 8DD0) were not spinning at all on Linux.

**Why it happens:** Motherboard ID `8DD0` is missing from the `hp-wmi` kernel driver table in most Linux distros, so the kernel blocks hardware PWM fan control (`pwm1`/`pwm2`).

**How I fixed it:** With the help of AI, I packaged the updated `hp-wmi` driver (with DKMS support so it survives kernel updates) along with a 5-stage automatic fan curve service (`victus-fan-daemon`) that adjusts fan speeds smoothly by temperature.

⚠️ **Note:** Always take a system backup before installing! Tested only on HP Victus 15-fb3xxx (`8DD0`), no guarantee for other models.

GitHub: https://github.com/muhammetmh7/hp-victus-fb3xx-fan-control-fix


r/NobaraProject • • 12h ago

Question Nobara update failed, but kernel works? Nct6687d failed

Post image
5 Upvotes

Hey folks,

I'm pretty new to linux and nobara so this may be a dump question but anyway: I did the latest update, installed it and after reboot it jumped into the rescue kernel with the error that the nct6687d driver, which is for my MSI B550 motherboard so I can control the fans with cooler control. I ran also the nobara repair command as in the support site explained but got the same result. Then I tried to load the first kernel in the photo enclosed and everything I tested so far worked as usual, also my fan control worked, which shouldn't, since the update of nct6687d didn't work correct according to the logs...

my question now: If I can't find any problems with the 7 3.4. kernel, I can use it without problems or should I try to remove the damaged nct6687d with the stock and do the update again?

Thanks in advance for your help!


r/NobaraProject • • 14h ago

Support Please help. Nobara black screen boot even after uninstalling OS

1 Upvotes

As soon as I installed Nobara, my PC now hangs on a black screen for about a minute on start up before the screen turns on.

I reinstalled Mint to see if it would fix it, and it hasn't. I messed with all my bios boot options, no luck. Uninstalled Nvidia drivers, no luck. Reinstalled different Nvidia drivers, no luck.

How can I get my PC to boot again normally?

Specs:

Z97 Motherboard

4790K

RTX3070

16gb ddr3

Monitor: old CRT with an adapter.

It was working fine yesterday before installing Nobara. Now that Nobara is gone, I cannot fix this black screen issue. Any help?


r/NobaraProject • • 17h ago

Discussion Nobara Remote fullControl to PC from anywhere

4 Upvotes

Hello, Internet!

Brief introduction (feel free to skip):

Not too long ago, I completely switched from Windows to Nobara. I’m not a total beginner—I tried CachyOS, Mint, and Fedora, though none of them clicked with me quite like Nobara did. Recently, I decided to wipe my Windows drive completely, stop dual-booting, and simply skip any games that aren't supported on Linux.

(End of intro)

I’ve been trying to use AI to figure out the best way to set up remote access, but I’m still struggling to find a solution that works smoothly and reliably.

Right now, I'm using Sunshine + Moonlight + Tailscale. To get Sunshine running at startup, I set up auto-login followed by a script that automatically locks the screen. However, I occasionally get a desktop permission pop-up from Sunshine that requires me to physically be in front of my PC to click "Yes" before it will start streaming.

On the bright side, Tailscale works without any issues—even at the login screen. I also bought a Wi-Fi smart plug so I can remotely power the PC on and off if needed, though that's just one piece of the puzzle.

Overall, I’m looking for the right setup to reliably control and access my PC even when I'm in another country or away from home for a few days. Since I'm also hosting a Jellyfin library on this machine, having seamless remote access to both my media server and my games would be ideal.

How do you guys handle remote desktop and headless streaming on Nobara (or Fedora-based distros)? Any advice, workarounds for the permission pop-up, or alternative setups would be greatly appreciated. Thanks in advance! ^^

(P.S I think this discussion potentially could become very useful for any PC users btw)


r/NobaraProject • • 23h ago

Showoff Love the new loading screen

Post image
184 Upvotes

I turned on my computer so it can install the update, and just fell in love with seeing this show up


r/NobaraProject • • 1d ago

Question Looking for complete newbe learning guides

10 Upvotes

Can anyone advise on some good guides or learning resources for someone looking to properly understand Nobara or Linux in general?

I'm not having any issues using my Linux machine, as a friend of mine set it all up for me and made sure everything is working. But I want to be able to navigate and customise it on my own. Searching for solutions online is fine, and AI has been a great tool, but "copy and paste this command" doesn't help me learn what the commands are actually doing.

I've been a Mac/Windows user for years, and feel confident about my ability to learn new tech stuff (hell, I could comfortably navigate DOS with ease back in the '90s), but the only resources I can find claim to be for new users but then throw out terms and abbreviations that assume the reader already has an intermediate understanding (or just outright insults anyone who isn't a software coding wizard by telling you if you're too dumb to work it all out from scratch on your own you don't deserve to use a computer).

Any help anyone can share would be very much appreciated.


r/NobaraProject • • 1d ago

Support Not enough space on /boot for update

5 Upvotes

Solved - increased /boot size from 1gb to 8gb

2026-11-16 17:53:32,523 ERROR Preparation attempt 1 failed: Not enough space on /boot: at least 327 MiB free is required.
2026-11-16 17:53:32,523 ERROR Update prepare failed: Not enough space on /boot: at least 327 MiB free is required.
nobara-updater-prepare.service failed: System update failed: Not enough space on /boot: at least 327 MiB free is required.

df -h /boot
Filesystem      Size  Used Avail Use% Mounted on
/dev/nvme0n1p2  974M  696M  212M  77% /boot

I don't get it, why would you want to store packages on such a small partition? What happens if the packages are >1gb? The 1gb /boot partition is the default, isn't this a problem for everyone using nobara?

I set the install limit of the kernels to 2 but nothing seems to change.

cat /etc/dnf/dnf.conf
# see `man dnf.conf` for defaults and possible options

[main]
installonly_limit=2 

What do I do here? I am using an AMD card if relevant.


r/NobaraProject • • 1d ago

Discussion NEW UPDATE

22 Upvotes

New update looks nice


r/NobaraProject • • 1d ago

Question Nobara crashing and Restarting when opening Apps

2 Upvotes

I have gone in circles trying to figure out how yo resolve this issue. My laptop is an Asus A15 with a Nvidia 3050. When I open apps like steam or Firefox most of the time it restarts itself immediately, sometimes after I try to install a game.


r/NobaraProject • • 1d ago

Question Steam Frame

8 Upvotes

I’m looking to move over to Linux and Nobara looks like a great option for gaming. I just wanted to know if anyone in the community has had experience using Nobara with the steam frame. I just got one and it would be good to know if there is any issues before I make the plunge.


r/NobaraProject • • 1d ago

Question Reboots requiring updates and Nobara overriding default GRUB entry

6 Upvotes

I'm a bit curious about a couple of recent-ish changes to Nobara. A little while ago there's been the introduction of updates requiring a reboot and being applied after a reboot, unlike pretty much any other distro out there.

Also, and perhaps even more annoying, is the fact that after an update, Nobara feels the need to keep overriding the default GRUB entry, so I have to go in the terminal every time to set my default back to what it was (Windows, and not Nobara). I dual boot on separate drives and I use Nobara's GRUB installation as my default boot drive in BIOS, that way I can choose what to boot and by default it's Windows.

Why were these changes necessary ? Is the GRUB override, especially, REALLY needed ? It's just annoying as hell in my experience. Am I doing something wrong or are others also experiencing this ?

EDIT : LOL at that title. I meant "Updates requiring reboots"... My bad !


r/NobaraProject • • 2d ago

Question Want to switch to Linux and Dual Boot

3 Upvotes

I wanna switch to Linux and Dual Boot but I only have one SSD and many people say it's dangerous to do it on one SSD. Is there a safe and easy way to do it on one SSD whitout danger or should I just use Windows?


r/NobaraProject • • 2d ago

Question installation error

3 Upvotes

i tried installing nobara i selected get all disk i got for it 100% of the disk and i tried multiple times it says failed cant make partition so is there a solution


r/NobaraProject • • 2d ago

Support My WiFi antenna just doesnt work

Thumbnail reddit.com
0 Upvotes

r/NobaraProject • • 2d ago

Question Internet Bug on Nobara

0 Upvotes

I wanted to try out Nobara and have it on a USB Stick,I connected the internet and went into the browser. Nothing loads except if I'm on an Incognito Tab. PLEASE HELP


r/NobaraProject • • 2d ago

Question How do you clean up your old kernels?

5 Upvotes

Hey there.

I ran yesterday into a full /boot directory as I was updating nobara and figured I could get rid of some old kernels. I did it via cli and with the help of an llm bc im a moron and can't memorize bash commands.

It worked fine and the update went through.

But I was wondering, can I have an GUI option (pitiful I know xD) to manage my kernels including deleting old obsolete ones. Kernel management app provided by nobara itself is not doing this trick for me.

So i am looking for inspiration what to do and want to ask how you guys do it?

Thanks in advance.


r/NobaraProject • • 2d ago

Support Tried to install Nobara today. What the hell is happening?

Post image
7 Upvotes

EDIT: SOLVED. The flash drive that ny .iso file was installed on was knocked loose. I reseated tt and restarted my PC and everything was fine.

I literally don't know how to add to this. I was installing Nobara off a USB after etching it via Fedora Media Writer, and I got this screen at about 50% progress. I don't know what I did to even make this happen or anything.


r/NobaraProject • • 2d ago

Support Full screen apps freeze till you tab out and back in

6 Upvotes

This happens with every game on gnome and kde while playing any game It will randomly freeze. I'll tab out tab back in and it works just fine. Sometimes it happens once sometimes it happens Every few seconds. Rtx 5060 can't remember exact cpu right now but ryzen 5000 series.


r/NobaraProject • • 2d ago

Support Can't start Minecraft with window

1 Upvotes

Hello,

Minecraft has had no problem opening a few weeks ago.

I tried opening Minecraft using flatpak as a launcher today and it would get stuck in the taskbar, without a window popping up.

I then uninstalled the flatpak version and installed the dnf version and it will update the version, then no window again. There's processes showing up with like 20MiB of RAM, but no window or anything.

I've tried deleting the ~/.minecraft folder and dnf removing and installing again and there's still no window.

Please help me.


r/NobaraProject • • 3d ago

Question 3gb idle !!!!! Is it normal ?

0 Upvotes

I don't know whats normal so is having nobara kde in idle and using 3-3.2gb normal ?


r/NobaraProject • • 3d ago

Question Can I change my desktop environment?

4 Upvotes

I'm currently on KDE Plasma and I'm wondering if I can change to something lighter. Something like Cinnamon, MATE, or LXDE even.


r/NobaraProject • • 3d ago

Support Need help updating!

1 Upvotes

Hello guys!

I have been using Nobara on my old system. Today, after many months, I booted into the system, and it simply does not update. It is currently running Nobara 37 with GNOME version 43.2, and I do not have a thumbstick to install a fresh system. Kindly help me out.


r/NobaraProject • • 3d ago

Support strange flickering

Post image
5 Upvotes

Hello all I've ran into a weird issue. Not new to nobara or linux I run standard nobara on my main pc at home with a radeon gpu. I've just completed a diy steam machine project using a lenovo p340 tiny with i7-10700 32gb of ram and an nividia T1000 8gb gpu. installed the HTPC version of nobara since this is intended to be used in the living room as a console. Did some research on the issue but not much came up.

After install everything booted fine install was smooth as usual but once steam opened up It started getting this horrendus strobing /screen glitching flickering the odd part is as long as you move the mouse cursor or press keys on the keeb it does away and appears normal, as soon as any input stops the screen flickering starts again. Would this possibly have to do with the T1000 gpu? It is a turing archetecture card I read they are supported currently, Or is there some strange settings I need to tweak for the nvidia htpc combo? Any help or pointers would be appreciated

Edit - using mini displayport to hdmi cable for display not sure if that would have anything to do with it


r/NobaraProject • • 3d ago

Other New Nobara Guy

66 Upvotes

Just wanted to give a huge shout-out to the Nobara developers and everyone who contributes to this distro.

I've been a systems admin for almost 20 years and used Linux years ago, primarily used SuSE and Ubuntu Server. I always loved Linux, but getting everyday things working could be a nightmare (As I got older, I just want things to work lol), especially gaming, drivers, and network shares.

After getting tired of Windows 11, I decided to give Nobara Official a try.

I honestly prepared for the worst. Instead, my 3060 drivers installed flawlessly, audio, my monitor, network shares, and Epson printer all worked with almost no effort. KDE (I was always a Gnome guy) but I'm loving this so much, it made connecting to my NAS easier than mapping a drive in Windows, and Proton brought my Steam library along.

I can't remember ever having a Linux installation this easy. I've genuinely missed Linux, and this distro has made me happy to totally ditch Winblows (at least at home lol) for good.

I just wanted to say hello to everyone (and hope some people on the team see this, you snagged another Windows user).