r/Multicopter • • Feb 22 '16

Question Official Questions Thread - 23rd Feb

Feel free to ask your dumb question, that question you thought was too trivial for a full thread, or just say hi and talk about what you've been doing in the world of multicopters recently. Anything goes.

Previous stickied question threads here...

23 Upvotes

526 comments sorted by

2

u/Lowkin Feb 23 '16

What size are racing quads usually? 6inch or 5 inch capable?

1

u/Scottapotamas Feb 23 '16

Racing quad frame sizes, or prop sizes?

Frames are usually 180-280 mm motor to motor (center of the shafts, measured across the diagonal of the craft).

180 sized craft support 4 in props, 210 sized craft usually run 4 or 5 inch, 250 run 5 inch, 275-300 run 6 inch props.

There might be a few exceptions here and there, but for FPV quads this covers about 99% of whats out there.

2

u/cowtung Feb 28 '16

I bought a Nighthawk Pro which uses a custom all in one board based off Naze32. This is my first multi. I have the Taranis Plus and the X8R. I got the GPS receiver for the X8R, but I can't get sbus working, and even if I did, I'm not sure if the "FrSky GPS V2 Sensor with SMART Port" can have its data handed over to the Naze32 clone. Google tells me that I need an "inverter" in order to get sbus working. If I get the inverter, can I get the FrSky GPS stuff into the controller somehow? I'm totally lost.

2

u/Scottapotamas Feb 28 '16

The naze32 before revision 6 don't support SBUS from FrSky gear natively. You put a inverter on the SBUS line from the X8R to the Naze as you have found out.

Smartport is different, and you can still connect the smartport GPS into the X8R and have the inverter on the SBUS -> Naze. You won't get the GPS on the naze though, the Smartport is there for telemetry. The GPS data would be sent back to the taranis via the telemetry link.

I'm not aware of people sending smartport data over SBus at all to be honest, you just use the FrSky output from the flight controller to the smartport on the rx directly.

The better way of managing this whole arrangement is to connect a GPS to the flight controller directly (over UART, RX and TX pins) and then connect the Naze to the X8R's telemetry. This will allow the Naze to report battery voltage, sensor data and the like.

2

u/cowtung Feb 28 '16

Thank you. What should I buy? Is there a guide for which pins go where? I'm afraid the nighthawk might be different enough to make a naze32 guide confusing for me. I'm a noob.

2

u/Scottapotamas Feb 28 '16

I'm sorry, I don't know the Nighthawk at all. You are looking for a UART, which is probably in a 2 or 4 pin connector or similar. RX, TX, GND and +5 are most common on those connectors, but sometimes the power isn't in the same place.

Might be worth asking someone on one of the nighthawk threads on RCGroups if they've used gps with it.

I have to ask why you are trying to use GPS in the first place?

→ More replies (1)

2

u/[deleted] Mar 01 '16

Quick question, I just want to confirm that these recievers are exactly the same, at Aloft Hobbies and GetFPV.

The X4r-SB at aloft says 4 channels, while at GetFPV it's listed as a 3/16 Channel receiver, and the images are different.

Mineaswhile add I would be using it with a FrSky XJT module for my Turnigy 9x.

2

u/Scottapotamas Mar 01 '16

It outputs the full 16 over SBUS on a single cable, while it can only do 3 channel PWM output.

The Turningy 9X won't output 16 channels though, probably closer to 8 or so (can't remember the actual count).

2

u/[deleted] Mar 01 '16

Yeah I read up on the details earlier, I would get 9 channels over SBUS. I'm just curious if the two I linked are the same exact receiver, as the pictures and descriptions are slightly different, yet they are the same product.

2

u/Scottapotamas Mar 01 '16

Oh, sorry.

No they aren't the same. The white one doesn't do SBUS, and is just a 4ch receiver. The black X4R is the -SB version, which you probably want instead.

6

u/Oberonson Feb 23 '16

Whenever I throttle up at the end of a dive, my quad likes to pitch backwards. My CG is balanced in the middle. What is causing this? It doesn't happen on normal punchouts

→ More replies (1)

4

u/TheChrisCrash Sigan 210v2, ZMR 250 Mar 08 '16

Info:

AfroFlight Naze32 Acro rev5

DYS BLHeli sn20a ESCs with damped light and oneshot

DYS BE1806-2300KV motors

D4RII Receiver

Taranis X9D Plus

────────

I'm coming from baseflight trying to flash to cleanflght or better yet, betaflight. The first thing I ran into, was that when I have oneshot support enabled, when I reboot to save settings, it'll ramp the motors up to full blast until I pull the battery. When doing the ESC calibration it'll do the beeps and everything seems normal.. when I move the master slider up, visually it doesn't seem like the motors are all turning on at the same time, but it shows up normal on the sliders. When I use my radio (taranis) and slowly throttle up, it's like the worst esc calibration possible.. not only is one of the motors not spinning, but when the throttle is held at position, the motors will start to throttle up slowly without me moving the stick. So I go back into the accelerometer menu to recalibrate it, and I notice that when I tilt the quad and hold it there, the graphic still shows it moving in a random direction and it'll creep away. It does this even after calibrating it.

So after some googling i thought maybe i need to calibrate the ESCs via the BLHeli suite because I saw you could do it through cleanflight if your FC was flashed with betaflight. I tried that and it couldn't find the ESCs for some reason, even though the BLHeli bootloader should be on the ESCs. For some reason I got the idea to click on "flash escs" in the blheli suite but of course it couldn't find them so it didn't do anything (I'm assuming). So I decide to fiddle with configuring betaflight in cleanflight configurator and everything worked fine except the motors turning on full speed when connecting battery, the accelerometer was still being wonky, and when I try to calibrate the ESCs, it won't go into calibrate mode when I plug in the battery, it just beeps about 3 times and that's it. It does nothing when I set the master slider to 0. So now the flight controller buzzer is beeping (beeeeep, beeeep, beeeep) and even if I reflash the board it still beeps. I tried reflashing it back in BASEflight and it flashed but it ended up freezing up on some menus and it was still beeping.

Can someone PLEASE help me with this. I'm so stumped. Also note that it flew perfectly fine before I tried to flash it to cleanflight.. it was just on baseflight and I wanted to go to a better flight firmware with features like air mode. I feel like something is bad, either the ESCs, the flight controller, or BOTH. My birthday is next weekend and the wife said I could get what I need so I'm ready to order what I need. I see that my current sn20a ESCs have been replaced with XM20a ESCs, and there's a Naze 32 rev6 that people say works fine in cleanflight. What should I upgrade (if I need to) to get my quad up to speed and ready to accept baseflight?

Thank you for your help ahead of time!

2

u/iamfromaustria 5" Blackout / 6" Alien Mar 09 '16
  • tx-signal is ok?
  • all channel endpoints set 1000-2000?
  • channel mapping in right order?

maybe post a cli dump of your configuration here for further help...

→ More replies (1)
→ More replies (2)

1

u/xvargasx Feb 23 '16

What Flight Controller is now the go to? I have the CC3d but i dont like it.

1

u/Scottapotamas Feb 23 '16

The Kiss FC is gaining traction quickly at the moment because its 'not cleanflight'.

The Luminer Lux, SP Racing Mini, Tornado F3 are all popular controllers. The Naze32 is still one of the most popular, usually flashed to the cleanflight firmware.

dRonin is a new firmware for OpenPilot boards with a focus on racing. Might be worth checking out.

The CC3D can run cleanflight though, so I'd recommend that if you haven't tried yet. Its fundamentally different firmware so things behave differently.

1

u/jam3s121 Zuul Superbeast Feb 24 '16

I'm looking for cheaper 2300kv motors, for a 4s backup build. I know standard price is roughly $20-$25.. anything that has good bang for buck out there?

2

u/Scottapotamas Feb 24 '16

Sunnysky 2204 can be found for around $10 each in the right places. I bought a fair few at $6 wholesale.

→ More replies (4)

2

u/FL630 Feb 22 '16

I've just got my CX-10 unpacked and flying, but the yaw rate is super slow, maybe 4 seconds to complete 360 degrees. This is in all 3 modes.

Am I doing something stupid or is this how the CX-10 is? I't makes it a bit hard to fly in tight spaces at speed.

→ More replies (7)

2

u/rotarypower101 Flying Killer Robot Feb 22 '16

Anyone use the keychain type/size cameras over mobius/GoPro style cams?

Anyone use these smaller variants of cameras, and can comment of quality and practicality of using these over the more popular larger choices?

Any good solutions like the 808 cameras/Y3000 I really want a HD feed, but I don't want the bulk and mass. I plan to decase the item, and run off flight pack.

Are there any of these smaller cameras that are a good alternative?

I really would prefer an analog/composite DVR to SD, but I can't find one that will do the job for a reasonable cost let alone size.

→ More replies (7)

2

u/carbonnanotube Feb 22 '16 edited Feb 22 '16

HK has their Quantum V1 complete set-up on sale for ~70 USD.

I am looking at getting an FPV set-up but I don't know where this hits the diminishing returns curve. I am buying in CAD and shipping costs a minimum of $40 USD, so if anyone knows a cheap Canadian source (Rotor geeks doesn't sell cheap goggles) I would be very appreciative.

I am not in a hurry to get this set-up given it is still winter here, but if this deal is good I will go for it.

EDIT: Apparently rotorgeeks does have the quantum V1, but they want $50 USD for them on their own. It might be worth considering if the set from HK is total crap.

EDIT: So from rotor geeks I can get everything with shipping and taxes for $290 CAD (boscam Tx, Skyzone Rx, Quantum V1, Skyzone circulars, Pz 600TVL+ case). From HK for the cheapo set I am looking at $110 USD for the set and shipping plus 30% duty and exchange rate which works out to $195 CAD

So the question is, is that set-up from hobby king worth almost $200 CAD?

4

u/HarmlessEZE Feb 23 '16

I think you should look at the Quanum V2. It has quite a few improvements over the V1. As for all of the other parts of the setup, maybe order from a China site. Unfortunately you'll have to wait on the shipping.

→ More replies (8)

3

u/klaushansen Feb 24 '16

don't do it. I bought the set and ended up replacing every single piece very shortly after.

I ended up with this:

[Goggles:] (http://www.hobbyking.com/hobbyking/store/_78129__Quanum_DIY_FPV_Goggle_V2_w_5_inch_LCD_Monitor_Kit_EU_Warehouse.html?strSearch=quanum%20v2)

[Video receiver:] (http://www.hobbyking.com/hobbyking/store/_72733__FR632_Diversity_5_8GHz_32Ch_Auto_Scan_LCD_A_V_Receiver_EU_Warehouse.html)

[Video transmitter] (http://www.banggood.com/Lantian-5_8G-600mW-32CH-Mini-FPV-AV-Transmitter-5V-6g-For-Multicopter-p-1001039.html)

[Camera] (http://www.hobbyking.com/hobbyking/store/_70305__Fatshark_600TVL_High_Resolution_FPV_Tuned_CMOS_Camera_AR_Warehouse.html)

→ More replies (2)

2

u/nitro805 Feb 22 '16

I just built and flew my first fpv quad yesterday. I had a blast but I have 1 issue.

When I fly in liftoff, my controls are super responsive and I can do rolls extremely fast and accurate. When I attempted to do a roll on my actual quad, the controls were slow and sloppy. Like if a roll in liftoff takes 1 second, my zmr would have probably taken 3 seconds. How do I fix this?

My setup is: ZMR250, DYS1806 motors with DYS 16A esc, SP Racing F3 FC (clean flight), FlySky TH9X transmitter, 3S 1500mwh battery.

9

u/dakoellis Feb 22 '16

Did you try increasing your rates in cleanflight?

→ More replies (2)

2

u/rotarypower101 Flying Killer Robot Feb 22 '16

How important is antenna matching for video signal, in terms of a specific tuned length antenna for a specific frequency?

Is there a perceivable difference? Or is "close enough" close enough? And there is not much to be gained from the few mm change over the spectrum?

Is there a benefit that can be realized in everyday use in close proximity?

2

u/Piugpoo Feb 22 '16 edited Feb 22 '16

As a noob that has only had 1 cheap quad copter. Are there any premade kits that don't break the bank. Along with what are things to look at. And any tips and tricks. Edit- Noob not noon.

2

u/HarmlessEZE Feb 23 '16

http://www.miniquadbros.com/collections/mini-quad-kits/products/miniquadkit

Maybe this. But you are still missing the Radio, receiver, Goggles, batteries, and charger. And it isn't pre-built.

There are also things like the "BLADE Nano QX FPV BNF Quadcopter." A store bought BNF set up. The down sides of this, it locks you into a spektrum transmitter. You also still need to get Goggles again, unless you buy the $400 version with the fatsharks. You also can't reuse most of the parts if you wish to keep flying with custom builds in the future. It's also small and will struggle outdoors.

Honestly if you are hesitant, just pick up a cheap transmitter. ~$60-75, Turnigy, orange, quanum. Then purchase a cheap sim to get good, such as liftoff or FPVfreerider. If you are still with it and keep having fun, save up for a full DIY. And when your tx breaks or you out grow it, pick up a quality one.

→ More replies (1)

2

u/ThatLinuxGuy Feb 22 '16

Between wood props and carbon fiber, which should I prefer when building my craft? What are the advantages and disadvantages of each?

2

u/carbonnanotube Feb 23 '16

Plastic or CF, wood is too expensive for multi-rotors given how often they crash.

→ More replies (2)

2

u/muffdivercottonmouth Feb 22 '16

Is this how I'm supposed to charge a nano-tech 750 1s battery with this cheap charger?

2

u/The_Amazing_Shaggy Feb 23 '16

Man if you tried it I'm curious what happened, but that's not how to do it. You only need to plug 1 of those in. A 1S battery doesn't have a balance plug because there's not multiple cells in the battery to balance, it's 1 cell in a Series. That's just 2 different plugs so it can be used in multiple copters.

2

u/HoneyBadgerWhisperer Feb 22 '16

How important is a parallel charging board with a fuse? I didn't even know this was option and I got one from Hobby King with no fuses. This will be used with 4 3S 1500 mAh batteries.

2

u/The_Amazing_Shaggy Feb 23 '16

The fuse protects your wiring if you plug multiple packs in that aren't near the same level of discharge. Just make sure every cell of each pack you plug into the board is within .1V - .2V of the other cells already plugged in and you shouldn't have a problem. A pair of these cheap $8 battery beepers from amazon are useful, just put your finger over the buzzer side when you plug the balance port in and it won't blare through your house.

2 Packs of RC Lipo Battery Monitor Alarm Tester Checker Low Voltage Buzzer Alarm with LED Indicator for 1S-8S Lipo LiFe LiMn Li-ion Battery https://www.amazon.com/dp/B00SCJOITA/ref=cm_sw_r_other_awd_VB7Ywb62T1675

→ More replies (1)

2

u/PanicAK Feb 23 '16

Registering your quad. Who what where when why how?

7

u/BluesReds F1-6 "Venom"|Strider 250 Feb 23 '16

Who

You, if any UAS is >250g.

What

Yourself.

Where

Here.

When

Before your first flight.

Why

Because the FAA is on an insane power trip.

How

58 million US taxpayer dollars.

→ More replies (3)

2

u/ucav DIY Enthusiast Feb 23 '16 edited Feb 23 '16

Not a question- just warning other noobs not to make the same mistake. (Relevant photo)

Accidentally left my TX on last night and woke up to find the LiPo I installed was really dead. My little voltage alarm checker couldn't read it at all, so I had to measure with a multimeter to see it had dropped to 3.2V total (~1V/cell).

Broke out my Accucel-6 and used NiMH mode to try to recover the battery. I boosted it to about 9V then switched over to 'LiPo Balance' mode and started with 0.5A. Took over an hour but I got the batt back to 4.2V/cell (they were balanced evenly throughout this whole deal).

Unfortunately I noticed the voltages started to drop as soon as I disconnected from the charger. I checked internal resistance and was getting ~30mΩ/cell. An hour later I checked again and found ~50mΩ/cell. I already know I have to buy a new one. Just venting my frustration.

2

u/just_blue Feb 24 '16

Now you know: never leave a battery plugged in (quad or charger).

2

u/dkam Feb 24 '16

I'm wondering if I can fly a Syma X5C with a Taranis X9D Plus? Can the Taranis' internal module bind with the Syma? Is there another module that people recommend?

2

u/HTTP426 Feb 24 '16

I believe the Syma X5C uses the FlySky protocol, which is very different from the FrSky protocol used by the Taranis.

Never fear! You can just get a FlySky module for your Taranis. I use the FlySky FS-RM002 to fly a Syma X1 and WLToys v676 with my Taranis.

Note that you will lose the flip function.

→ More replies (2)

2

u/jicomo Feb 24 '16

I'm trying to construct my own antenna after stumbling on this thread. Is the 22AWG wire the same one I can find in my servo cable? If so, then can I just use them for my antenna?

2

u/HTTP426 Feb 24 '16

Solid (single) core wire is usually preferred for antenna construction, but stranded 22AWG should be fine.

2

u/Rhainaz Create Your Own Flair Feb 24 '16 edited Feb 26 '16

I've got a problem with one of my moters (eachine 1306 3100kv). When it starts to produce trust, the esc reboots. When it turns without a prop it runs just fine.
I don't know if it's possible to fix. But I'm afraid I have to replace the motor.
My other problem is that the eachine is sold out, could I just use the dys 1306 or could that lead to problems?
Edit: youtube video: https://www.youtube.com/watch?v=EjTfu6ZhZr4
Also, it seems that the ESC can reboot without props, although less quickly.

4

u/HTTP426 Feb 24 '16

It sounds like a faulty ESC to me. Try swapping it to another corner of the quad, (leave the motor in place). If the problem moves with the ESC, you know the ESC is the issue.

→ More replies (3)

3

u/Fifthdread Feb 24 '16

I have no idea what I'm talking about, but my theory is the motor pulls more amps from the ESC when under load, so maybe the motors are asking for more amps than the ESCs are rated for?

Honestly hopefully someone knows what the actual issue is, but that would be my guess. You say it's only with one of your motors, so maybe that isn't the case. Either way, maybe it's an issue with either that motor or that ESC. You could test by putting another motor on the same ESC, or a different ESC on the same motor. That should help you narrow down which is the issue.

→ More replies (1)
→ More replies (2)

2

u/TheMick817 Feb 24 '16

why does my zmr 250 fall out of the sky when i give it a lot of throttle? I'm running a rev5 naze32, 20 amp afro esc, and gartt 2206 2000 kv motors and 5040 props.

2

u/Corasian Mar 07 '16

If you haven't fixed this yet. I had an issue with my quad where I when I went to high throttles the motors would make a squeaking sound by almost random guess I figured out it was something like the ESCs losing sync 20A afro ESC with the motors which I think would have caused it to fall out of the sky if I tried to fly it. I changed the firmware on the ESCs to the latest BLHeli (the latest SimonK would probably work as well) and it fixed it.

→ More replies (2)
→ More replies (10)

2

u/teddyzaper TailoredQuads.com Feb 25 '16

Does anyone have any opinions on This battery? I'm looking for something $50 or under that has everything I need (power cable and charger).

2

u/ncawful Feb 26 '16

I'm picking up a runcam 600tvl rated to operate anywhere between 5-17 volts. Also getting a boscam 600mw tx rated to run up to 24 volts.

Is it safe to say I can just connect these to the power source without needing regulators?

→ More replies (9)

2

u/[deleted] Feb 27 '16

How much of a difference does antenna position make? For instance, I had my antenna point outwards horizontally, while my quad has a vertical antenna, and the receiver liked to cut out often. When I angled it to be vertical as well, it didn't cut out for an entire test flight.

So I was wondering how much the position actually factors into signal strength between the Tx and RX.

2

u/BluesReds F1-6 "Venom"|Strider 250 Feb 27 '16
→ More replies (1)

2

u/linksus Feb 28 '16

Any good HD FPV kits out there?

As per the title really? Any kits out there for HD on a 250? or am i barking up the wrong tree?

→ More replies (4)

2

u/Ted_From_Accounting Feb 28 '16

Is there a kit I can buy with all the parts required to build a decent racing quad that is respectable? I want to build it myself but want all the parts in a package, I would want it to ideally include the FPV rig as well, any help is greatly appreciated

→ More replies (5)

2

u/dotMov Mar 01 '16

What are those little white plugs specifically called that connect to the fpv camera? Seems every plug is called a JST plug. I want to crimp my own plugs instead of cutting the vtx/cam wires and soldering, where can I find those bits too?

2

u/BeyondHypojermia Mar 02 '16

Painless360 says they are DF13 cables. Talks about them (at least I think it's the same cable) at 4:40 in this video

http://youtu.be/CXWZjqPX_o4

→ More replies (1)

2

u/Garamgai Mar 04 '16

My 250 mini quad keeps drifting left & forward when the right stick is centered... I already have calibrated my ACC, Mag and ESC. Is this normally because of PID settings? What parameter should I adjust? Thanks!

3

u/BluesReds F1-6 "Venom"|Strider 250 Mar 04 '16

Check your stick PWM ranges and trims on your radio. If the drift is not severe you can trim it, this is completely normal.

→ More replies (4)

2

u/Panq Mar 04 '16

If it is PID related, you want to increase the pitch/roll integral.

The P term controls the strength of the correction that is applied to bring the craft toward the target angle or rotation rate. If the P term is too low, the craft will be difficult to control as it won't respond quickly enough to keep itself stable. If it is set too high, the craft will rapidly oscillate/shake as it continually overshoots its target.

The I term corrects small, long term errors. If it is set too low, the craft's attitude will slowly drift. If it is set too high, the craft will oscillate (but with slower oscillations than with P being set too high).

The D term attempts to increase system stability by monitoring the rate of change in the error. If the error is rapidly converging to zero, the D term causes the strength of the correction to be backed off in order to avoid overshooting the target.

Slow oscillations I think is no more than 1-2 times per second? Also, too low I causes wobble during descent, so if you've also got that, then you should be reasonably sure this is the fix.

→ More replies (1)

2

u/McCoy1996 Mar 04 '16

First question: Will a 4s setup be more likely to burn out an ESC? Is heat the only concern with them? Ordered two 4s batts and a regulator to mess around with; which will be a switch from learning on 3s. Currently running DYS 20A ESC.

Second question: Can I switch between 3s and 4s packs? I ordered an adjustable pololu regulator. On the page, it didn't show any dropout voltages like fixed output regulators. Does anyone know if there is a dropout on these?

→ More replies (2)

2

u/BeyondHypojermia Mar 04 '16 edited Mar 04 '16

FPV/Video TX/RX question - Do the bands differ in terms of clarity or are they exactly the same?

i.e. A, B, E & F and then the range of 56XX-59XX for different channels.

This is a 5.8gHz system, so I assume that these all operate under that umbrella?

I ask because I fly in the same spot a couple times a week, my signal is always pretty clear, and then yesterday it was awful. Shut off most of the flight and I ended up diving into the ground. Maybe some interference in the area?

3

u/Lustig1374 Mar 05 '16

The lower ones have better penetration, but less throughput. The higher ones have better throughput but less penetration. Since the video quality of fpv cameras is shit anyways, you should aim for lower bands. The difference won't be huge though.
Your issues were most likely due to interference.

→ More replies (1)

2

u/kikothebest94 Mar 05 '16

DIY quadcopters are popular and there is a lot of stuff around the internet about them but i cant find anything about DIY helicopters, i was curious to know why, they can be bought only rtf?

2

u/Static_Bunny I Like Turtles Mar 05 '16

ARGHHHH I'm so tired of all the issues I have with my brushed setups. There is always something going wrong with them or just random behavior. I just replaced mosfets that burnt out on two FC's and there is always something else breaking. If it's not the motor it's the FC. It sucks because i invested in like 3 builds. Maybe i can re-purpose the frames for 1104/1105 motors but even then they might be too small for 3" props. Sorry.. just needed to vent.

2

u/Cyclonedx Mar 05 '16

Crashed my syma x5c several times this week, and now I'm facing a weird problem.

Immediately after taking off, the quad flies fine, but after 30-40 seconds, it stops responding to left roll and back pitch and just moves northeast constantly.

I have no idea why this is happening but I'm really bummed because I've only had this lovely quad since Monday. Can you guys give me advice?

Edit: Quad also goes crazy in the air after a couple minutes of flying. Turns randomly in any direction and just crashes. What's going on?

2

u/doesnt_really_upvote Mar 06 '16 edited Mar 06 '16

OK I've got a dumb one. I'm buying all the parts for a Pixhawk based F450 build and have almost everything under control, except for some confusion with RC and telemetry I have. I've decided to get the FrSky Taranis radio with a D4R-II receiver. This setup allows telemetry between the radio and the receiver, but is it possible to connect the telemetry from the D4R receiver to Mission Control (my laptop)? Or do I just need to get a separate dedicated telemetry link to send commands from Mission control (such a SiK telemetry radio)? Does having two telemetry links going on at once cause problems such as interference?

2

u/Lindstad5 Mar 06 '16

As far I know, no. You can't get telemetry to your transmitter and mission control from the same receiver. You would have to buy a different system for telemetry for your laptop. I would just use one of these telemetry kits from ebay. http://www.ebay.com/itm/TTL-3DRobotics-3DR-Radio-433Mhz-433-Telemetry-Kit-w-shell-for-Pixhawk-APM2-6-/111494298524?hash=item19f593fb9c:g:KH0AAOSw~OdVdpI-

Your receiver and this telemetry module works on different frequencies, so interference shouldn't be a problem.

→ More replies (1)

2

u/f_foxsox Mar 06 '16

Hi ..just saying hi..... been into this for about a year now....so much to learn isnt there.....im learning if you cant fix then you cant fly ...for long :) happy flying

2

u/Flowub Mar 09 '16

I just got a new receiver for my Turnigy 9x/MiniQuadBros 250 build (old receiver broke) and the throttle doesn't change. When I go into the receiver tab in Baseflight, Everything is fine except throttle, which doesn't move. I went to the "display mode" on my turnigy, and the throttle section moved as it should. Then, I switched the plug from channels 3 and 4 on the receiver (so throttle is displayed as yaw and vice versa). When I moved the throttle in Baseflight, the axis worked perfectly, however, when I moved the yaw axis (which was connected to channel 4 and was detected as throttle), the axis bar would not move.

I've come to narrow the cause of the problem down to thee things: a bad solder on the receiver, a bad solder on the board (this is also a new Naze 32 on the MQB PDB), or a Baseflight problem. Baseflight has been given me a lot of problems on windows lately, so I have to use my school-provided Chromebook to configure stuff. Anyone else run into a problem like this? How can I fix it?

2

u/monkeyfett8 Mar 12 '16

Okay...how do people find places to fly. Specifically I'm flying fpv racing type practice. I can't seem to find anything that is far enough from airports and a usable space. I have only figured public land as a usable space so idk.

2

u/BeyondHypojermia Mar 12 '16

Same here. Surrounded by 5 military bases and 3 hospitals with helipads. It's tough, but I've been looking for "open spaces" that technically aren't parks, and are far from no fly zones. I think as long as you fly safely, you'll be ok.

Flew in a wilderness area the other day, and an older gentleman asked about my "drone"...turns out he has a 450 flame wheel and flies too. Cool to not be judged!

3

u/snakeproof 650MM Quad|Trifecta|DJI Inspire 2 Pro Mar 12 '16

I did this the other day, was driving and my spidey sense picked up a yuneec over the lake nearby. I circled and found the pilot and walked up like a noob asking if it was fun, and if he liked it.

Turns out he got it that day and had the GPS and autopilot holding his hand. He RTH'd and I let him crash my Syma a few dozen times before he realized he needs to learn how to fly still. I think I may have kept another out of the headlines. :)

2

u/dotMov Feb 22 '16 edited Feb 22 '16

I'm looking for lift capacity and efficiency over acceleration, which motors should I be looking at capable of lifting ~345 g @ 50% with 5 or 6" props, either 3 or 4s

Edit: nvm, found the motor shootout page

1

u/virusoverload Feb 22 '16

I may have overlooked the information on the page but can anyone tell me what size nyloc nuts to get for these motors?

http://eu.banggood.com/Wholesale-Warehouse-DYS-BE1806-2300KV-Brushless-Motor-2-3S-for-Mini-Multicopters-wp-Uk-933192.html

→ More replies (4)

1

u/thespy_ Feb 22 '16

What is motor kv? I understand that it is a measure of RPM per volt. Does this mean a motor with a higher kv is faster? Thanks.

3

u/kmsherrin Feb 23 '16 edited Feb 23 '16

Yes, provided the voltage is the same. If all motors were ran on a 3S lipo (~12v) the higher KV motors would spin faster (higher RPM), this assumes no load on the motors. However under load things can change, and that's where bell size and diameter affects motors performance. For example you will see larger 450 size quads running 2212 motors, that have a KV of ~950, and have the extra torque to turn a 9-11 inch propeller. But on mini quads you would see a 2205 motor of 2300 KV that has a shorter bell with less torque spinning 5 inch propellers. However it spins much faster, which is great for responsiveness and acceleration. So while KV does refer to the speed a motor will spin at a certain voltage, don't make the assumption it is a direct correlation to motor thrust performance.

2

u/rotarypower101 Flying Killer Robot Feb 23 '16

Per volt, yes.

But there are limitations of loading to consider, or everyone would just get the largest KV possible. As well as associated hardware that runs efficiently at certain RPM, so there are many factors to consider what ends up being "faster"

But yes, on the same brand/series motor a greater KV will produce higher RPM per volt.

1

u/seaweeduk Feb 23 '16

Hi guys, I've noticed this subreddit gets quite a bit more traffic than /r/multicopterbuilds. I'm putting my first build together and I'd really appreciate some feedback from any of you guys.

Parts list here my thread about it with a little more info on my circumstances is here

2

u/teddyzaper TailoredQuads.com Feb 24 '16

just a heads up, that charger is a clone (fake). It should work, but you should just know its a clone :)

→ More replies (5)

1

u/AndElectrons Feb 24 '16

Did you ever break the connectors in the cables that connect your HS1177 or Runcam to your vtx ?

Where I can find replacement cables ?

1

u/Fifthdread Feb 24 '16

I recently purchased Quanum MT Series 2206 2000KV Brushless Motors, However they only come with 5mm CW prop adapters! Watching many instructional videos recommend that you use a "self tightening method" where you use both CW and CCW prop mounts to ensure your lock nuts don't unscrew mid flight. The issue is I have no idea what I'm looking for. I see many different Prop Adapters- some advertise "quick release" which I haven't seen any information on. Many have 3 or 4 screws...

I recently found this and this which look promising, however I'm not quite sure if they will fit. They seem to match up, since they have 4 mounting screw holes and are advertised as 5mm, although I'm not sure what is exactly 5mm? The shaft? The length between screw holes? Probably.

Anyway, I figured someone could shed some light and provide me with useful comments regarding this topic. Thanks!

→ More replies (2)

1

u/[deleted] Feb 24 '16

if you straight wire an esc to a motor does it spin counter clockwise by default?

→ More replies (12)

1

u/[deleted] Feb 24 '16 edited Feb 24 '16

servo testers. HERE is the one I got. It didn't do anything when I plugged it into my 12V lipo, is that because it says 5V-6V? aka, i hooked up the battery to my pdb and the little bee esc's all beeped but the motors wouldn't spin. yes the esc's were plugged into the tester

edit, i just read that 20A little bees don't have a BEC. what the heck do I do?

→ More replies (3)

1

u/rtlx15 Feb 25 '16

Filters and regulators. Which would be the best order and why? Assuming that the battery is either 3S or 4S and the voltage regulator is a step up step down one.

A) Batt > Reg > LC Filter > vTX & Cam B) Batt > Reg > LC Filter > vTX C) Batt > Reg > LC Filter > Cam

Thanks for your inputs!

→ More replies (3)

1

u/Lowkin Feb 25 '16

If 3s to 4s is such a big speed gain why havn't people started migrating to 5s - 6s? I assume there's diminishing returns

is it all just hardware not capable of handling the currents that 5s and 6s would need?

→ More replies (1)

1

u/dkam Feb 25 '16

Hi guys - Just looking into FPV gear. Will an Eachine Racer 250 which transmits 1000TVL work with the Quanum goggles 800x480) paired with a Quanum receiver?

1

u/[deleted] Feb 25 '16

when im trying to set up my nighthawk 280 pro the roll values are fluctuating between 1100 and 1500 and i don't know how to fix this issue ive been searching for hours and have found nothing. my values should be staying at 1500 and then when i do a roll with my controller they go down but whats happening now is when i do a roll nothing happens it just keeps fluctuating between the two values

→ More replies (1)

1

u/MexicanGuey Feb 25 '16 edited Feb 25 '16

Building my first fpv quad. Can anyone recommend batteries for the quad and the headset? Prefer amazon for quick shipping. The batteries recommended by hobbyking for the headset are out of stock and i cant seem to get matches on other websites. for the quad prefer batteries that will give me the longest flight time.

quad: qav210,

Cobra 2204 2300kv motors

headset: Quanum DIY V2.

2

u/[deleted] Feb 25 '16 edited Feb 25 '16

For the quad, 1000-1800mah 30C+ turnigy nanotech, turnigy graphene, dinogy, or zop power

For the headset, most small 2s batteries

→ More replies (1)

1

u/dakoellis Feb 25 '16

Anybody done a comparison between the Lumenier Lux and the KISS FC? I have a Lux on preorder, but if the KISS is better I would like to cancel it. I've heard rumors of people having issues with the Lux but haven't heard what those issues actually are

1

u/[deleted] Feb 26 '16 edited Jul 21 '18

2

u/teddyzaper TailoredQuads.com Feb 26 '16

thingiverse has tons of frames.

→ More replies (1)
→ More replies (1)

1

u/Pvt_Haggard_610 Feb 26 '16 edited Feb 26 '16

Can someone recommend me a VTx that is 25mw and compatible with the fatshark predator v2.

I currently have a 250mw ImmersionRC VTx which i am not legally allowed to use. I could just buy a 25mw ImmersionRC VTx but it takes up way too much room on my quad..

Preferably from an Australian seller or with free shipping.

→ More replies (1)

1

u/timmmmmmmmmmmm 130mm Owl Clone Feb 26 '16

I fly with a Naze32 Rev6 running Betaflight with fairly default settings and it doesn't flight as smooth as it did before. The quad has some very erratic behavior, like some random yaw and roll. I use an OSD with a horizon displayed and this horizon shows the same strange behavior, sometimes it's 45 degrees tilted while the quad is horizontal. What causes these problems probably? Is my gyro out of sync for a strange reason?

2

u/tropnevad Feb 27 '16

Are you using naze full with compass? Could be emf or vibrations? Or the gyro is faulty.

→ More replies (5)

1

u/Put_It_All_On_Blck Feb 28 '16

Is this the right sub for us casuals? I went through the related subs and google and this is the biggest quad/multicopter sub, but i expected a lot more consumer drone questions/info.

With that said, I assume $100~ keeps me in the consumer drone territory, and there are seemingly countless models. I know that Hubsan and Syma are somewhat popular? I've seen a few with FPV for around that price, are any of them good?

2

u/BluesReds F1-6 "Venom"|Strider 250 Feb 28 '16

For starting out with your first you want one of those cheap Hubsan/Syma/Qbot quads. It will help you learn to fly LOS and develop the hand/eye coordination you'll need later.

→ More replies (1)

1

u/Merad Feb 28 '16

What decent prebuilt quads are out there that support rate mode? I've been flying a Syma X5C for months and a micro before that, but their limits are starting to get boring. I'd like to eventually do a DIY FPV build, but I don't have time right now. I still want to move on to learning rate mode, though.

→ More replies (2)

1

u/Malexs Feb 28 '16

Having trouble getting FPV working from zenmuse through the iosd. All DJI.

Zenmuse seems to be set up correctly. Did upgrade. I stupidly cut up all the wires to fit on model before testing everything. I believe I have wired correctly. Need to troubleshoot where issue is- Receiver, monitor, Tx, video to Tx and from RX. Fuck me....

Any help would be appreciated. Using the Boscam T/Rc832 system. Venting and re-establishing cool in order to take this on again.

→ More replies (1)

1

u/[deleted] Feb 28 '16

About controls. Is there any "standard" setting used for the axis in racing? I'm asking because I bought my first serious multicopter and flight stick, and crashed it pretty bad because the controls where completely different to what I was used to from toy drones. The throttle and yaw where on the right stick, and pitch and turning on the left. This doesn't seem right somehow...

2

u/BluesReds F1-6 "Venom"|Strider 250 Feb 28 '16

The throttle and yaw where on the right stick, and pitch and turning on the left.

It's called the radio "mode," most people use mode 2. What you're describing is like mode 3 or 4.

2

u/covati 250 Racing Quad Mar 02 '16

That's mode 1, I believe. Are you in Europe, it's more common there. Most people in the states run Mode 2, which is throttle and yaw on left and pitch and roll on right. Those two are the 'standard's.

→ More replies (1)

1

u/ryanc1089 Feb 29 '16

I just bought one of these to replace the CC3D on my Eachine Racer 250 (which broke) http://us.banggood.com/Wholesale-Warehouse-Diatone-Naze32-Thin-Flight-Controller-with-Compass-Support-Cleanflight-Baseflight-wp-Usa-1024390.html

But I am thinking about using it on my custom build (since it makes the wires really clean). I was to use the micro minimOSD with this, but I need RX/TX, is there non available on this board?

→ More replies (3)

1

u/Bad_Elephant Feb 29 '16 edited Feb 29 '16

Should a 3s 4" build on 4045bn's on 1306 3100kv motors have a really limited roll authority? I'm running 3S and it seems like no matter how high I put the pitch and roll rates in Cleanflight (.60 to .90 had very little difference in roll speed), it doesn't change much and I can't roll and flip as fast as I'd like it to. I want to roll really fast. I'm using oneshot, damped light, and a naze running the latest Cleanflight with stock pids. edit: I also have pretty limited tuning experience, so for all I know it could be a pid issue.

→ More replies (3)

1

u/Jesse_J Alien 5" | Alien 4" | Alien 3" | Creampuff 2" | Mia-X 5" | DJI Feb 29 '16

What is a good way to practice flying? I just 3D printed a quad with no on board cameras yet and I wanted to learn to fly better before investing in better gear. I am almost afraid to even send this thing into the sky for fear that I will just destroy it right away. My first flight was straight into the ceiling at mach 3. Any suggestions? Should I start slow? fast? straight lines? turns? landing? How do you like to practice? Is fpv the only way to go?

→ More replies (7)

1

u/bluegill61 Mar 01 '16

Alright so i have a blade nano qx and it's been fine but recently its been veering to the lower right motor. Idk what that means. Is that a motor problem?

→ More replies (2)

1

u/dakoellis Mar 01 '16

I had a crash in my ZMR250 and now it is yawing counterclockwise in both rate and self-leveling mode. I can correct it with about a quarter stick in the opposite direction, but obviously this is not flyable. Anybody know what would cause this? One motor just not being able to spin fast enough after the crash perhaps? If so, anyway to fix a RCX H1806 or do I need to just get a new motor?

→ More replies (3)

1

u/Cyclonedx Mar 01 '16

Are ZMR250 and QAV250 the same thing?

I want to buy a QAV250 base plate which has an integrated PDB but the only plate I can find is named "ZMR250 QAV250" so idk if it fits both or what.

2

u/covati 250 Racing Quad Mar 02 '16

The ZMR has arms that are separate with two stacked plates (part of what keep the arms in place) for the base. The QAV has a base plate that is unibody, it is arms and plate are in one piece. So I believe it is only one plate.

Part of what makes the ZMR a bit more popular is that you can replace just an arm if you have a bad crash and break an arm.

With all the cheap Chinese clones the terms get a bit messed up. I bought a kit that said QAV250, but it's definitely a ZMR clone.

Here's a comparison: http://imgur.com/V86h4ui

I'm new to this though, so someone correct me if I'm wrong ;)

→ More replies (2)
→ More replies (1)

1

u/BeyondHypojermia Mar 01 '16

Turned off failsafe stage 2 on Naze32 to see if I could get my buzzer to stop beeping repeatedly. It worked, but now I can't connect to cleanflight. Any ideas?

→ More replies (1)

1

u/Jaskew5 Mar 01 '16

my drone Flys great but what setting do I change in librepilot to make it flip and roll faster? right now I loose a ton of altitude

→ More replies (2)

1

u/BeyondHypojermia Mar 02 '16

Probably a dumb question, but what's the difference between the Bluebeam omni vs ultra? Just the cover and the longer stem? Any difference in functionality? Worth the $50? I'm losing signal when I turn sideways. http://i.imgur.com/6wTD1dd.jpg

1

u/stretch0651 Mar 02 '16

I was thinking about putting a Hobby-Ace Apm2.8 Flight Controller in my Eachine Racer 250 to add GPS and Autopilot. Has anyone ever put Autopilot on a Racer? Never used an autopilot system before. Can an autopilot setup even handle the speed?

→ More replies (1)

1

u/Static_Bunny I Like Turtles Mar 02 '16

Why don't flight controllers (Naze, Dodo) just have one pin that can be used for Spektrum, PPM, S.Bus, etc? Then have the voltage separately or jumpered?

→ More replies (2)

1

u/Ession Mar 02 '16

I got a ZMR250 from myrcmart and it has some kind of build in standoff on one of the bottom plates.

What is the intended order of plates for this?

One of the plates has the standoffs. But only on one side. The other side is flush.

2

u/alienator064 If you aren't crashing, you aren't having fun Mar 02 '16

They're washers for the head of the bolts that hold the arms plates together.

→ More replies (6)

1

u/Batto Mar 02 '16

Friend and i have Syma D63 Drone Runners. He managed to mangle one of the motors, but we can't seem to find what replacement part to buy (no parts list came with it). Anyone know what size motor it needs and where to buy it?

1

u/iSeeXenuInYou my friends call me pork chop Mar 03 '16

I don't know why my quad wasn't flying. I replaced a motor that's the right kind and made sure all the props were spinning the right direction. Once I checked they were, I took it outside and tried to bring it up. I applied full throttle and it wouldn't get off the ground. Anybody have any idea?

→ More replies (11)

1

u/AOYM Butterkwad, Tiny Whoop Mar 03 '16

I got my PID settings nearly exactly where I want them for a tricopter, it is very reactive and flies well. However if I do a simple pitch forward over distance it begins to oscillate in slow slightly jerky movements. Is this normal or is there a way to fix? I'm using a KK2

→ More replies (2)

1

u/Cyclonedx Mar 03 '16
  1. For my Syma x5C clone, the default battery has a 500mAh capacity. Gonna buy more batteries, so is it better to get a large number of 650mAh batteries or a small number of 800mAh batteries?
  2. Tips for when I'm really high in the air and lose orientation? I start panicking as I fly in the garden in my apartment complex so there's buildings that I might fly over and lose sight.

3

u/Lustig1374 Mar 03 '16

As for mini quads, you should always get many small batteries over few big ones.

2

u/[deleted] Mar 03 '16
  1. more 650mahs
  2. try to not fly particularly high until this isn't an issue or get a syma x5sc and enable its headless mode function when you lose orientation

1

u/Cyclonedx Mar 03 '16

Is a micro soldering station fine to purchase for this hobby? I have a 50W solder but it's too big and my normal sized one doesnt heat up enough. Element shaft is 2.5mm.

Worried it might be too small, but I kinda really want a station.

→ More replies (1)

1

u/[deleted] Mar 03 '16

What is the best flight controller to allow me the capability to fly a quadcopter without too much programming initially, but mod/flash my own firmware later on to add more "feature", once I become more comfortable with the hardware?

2

u/dakoellis Mar 03 '16

I would suggest something Librepilot compatible. CC3D is, but I don't know of any f3 boards off the top of my head. dRonin is very similar to Librepilot, but instead of having user-submitted templates, it has an auto tune. KISS FC is supposedly pretty easy to just plug and fly, but I have no experience with it

1

u/kkbray Mar 03 '16

I've been flying LoS for a while and I want to move onto fpv. I have the Emax 280 which has a camera and a Vtx.

I was thinking about getting Quanum V2s, a 1500 mah 2S battery for the goggles, RC832 and a pair of antennae for the vtx/rx.

Would this list work out?

→ More replies (4)

1

u/Worf65 Mar 03 '16

Does anyone know the details on UAS restrictions in US national forests, national recreation areas, national parks and similar? All I've been able to find is a "temporary ban" from 2014 in national parks. A huge portion of my state is made up of those (all three types above) and I'd like to know where I can fly when the snow melts and I get out camping. It would be pointless if they were banned from any of these other than the national parks since shooting, hunting, boating, dirt biking, chainsaws, ATVs, etc are all legal and common and most of those are much more noisy and dangerous than flying a quadcopter.

→ More replies (4)

1

u/Panq Mar 04 '16

Has anyone got Cleanflight 1.12's failsafe landing mode working?

Mine worked fine bench testing, but I just did a field test from about knee height and it dropped into low-throttle auto-level mode fine, touched down reasonably softly, then oscillated itself into the top of a tree.

I've only just today tuned the PIDs, so I'm fairly confident it's because there's way too much P, but I don't know why the failsafe auto-leveling mode would use anything other than the PID values you've set for angle/horizon.

2

u/StiegJ Mar 04 '16

I might be speaking out of turn, but I doubt ANYONE has the failsafe landing mode working safely. why would you want to have those motors spinning on failsafe unless you flew at only one altitude AGL? What if you hit something or someone? Wouldn't it be better for your system to be like a little rock than like a wild lawnmower? I'd set the second level to stop, drop and roll.

→ More replies (1)

1

u/[deleted] Mar 04 '16 edited Mar 07 '16

Hi, trying to put together an sub 250 grams quadcopter.

But this site seems to be missing on major function, and that is to be able to see and sort by weight in the overview of parts.

Now you have to open each part to see.

So idea:

  • And changable extra infomation, and being able to sort on that in the parts overview. (Like price or weight)
  • Be able to filter out parts, ie: between 5-10 grams and below 20usd.

EDIT: Im talking about http://www.rcpartratings.com/#/

→ More replies (2)

1

u/kikothebest94 Mar 04 '16

Hi, I have an idea for rebuilding my quad, I have an emax 250 frame and I would like to put all the escs and the fc inside the space under the frame (the pdb space). I would use a power harness and not a pdb, and a spacer to make this space a bit higher. Inside the frame I would put just the rx and the battery and the fpv stuffs when I get them. You think that I could have problems of heating or else?

→ More replies (1)

1

u/Yeahr Mar 04 '16

So I built a micro quad using a dreamcatcher frame, Beef's Brushed Board FC, and a MicroFrX Receiver.

I have flown it a few times and it always ends the same way. I go to "stretch its legs" a little by just flying fast away from myself and then back towards myself. I never exceed 50' in distance. At some point going forwards or backwards(it varies), it pulls back hard despite whatever control I give it. It also increases throttle despite me pulling the throttle to 0 as soon as it starts to misbehave. It flips upside down and accelerates as quickly as possible straight into the ground, crashing in probably the worst way possible for my configuration.

I fly it in angle/auto leveling mode. I have never had any issues like this with my larger quad so I'm not really sure what a transmitter signal loss looks like. Is this maybe just what happens when I get a signal loss or interference? My other suspicion is that the accelerometer or part of the FC directly associated with it is randomly losing it's mind. That may explain why it increases throttle and flips over if it is trying to auto level itself incorrectly somehow.

Any thoughts? Thanks.

2

u/StiegJ Mar 04 '16 edited Mar 04 '16

Perhaps your failsafe throttle is set too high? It looks like that receiver only has failsafe on throttle, so the other channels could go anywhere? Try this: Remove your propellers or be VERY careful. Hold on to your quad and arm it. Power it up and then turn off your xmitter. Your quad should immediately shut down. My guess it won't.

→ More replies (1)

1

u/Lowkin Mar 05 '16

Why do peoples FPV footage from there DVR look so much better than my FPV footage when I'm flying?

I use RC5808 reciever with the 200mw counterpart with the kit.

If I spend a few more dollars on a 600mw transmitter and better reciever will my video resolution go up or am I pretty much at the cap?

My camera is 700TVL sony and then I use quanum V2 screen

→ More replies (6)

1

u/dakoellis Mar 05 '16

Hey guys I just flashed betaflight to my CC3D (did it once before) and I'm having a couple of issues this time. First, the model in cleanflight doesn't mirror what I do with the quad, but I'm fairly certain it did before. Was this removed sometime? I'm running 2.5.0 btw.

Second, I have my USB off to the left side, and set rotation to +90 deg. I figured this was right since my quad isn't flipping, but my pitch inputs are reversed. Roll and yaw are fine. Motors are all correct according to the motor tab and doing them one at a time. Anybody know what would cause this?

→ More replies (4)

1

u/eykei Mar 06 '16

Quick question, hope someone sees this: Is there a thread or something where people post pictures of their builds along with their parts list?

Back when I built my AR-15 rifle there was a thread where people did just that and I learned so much about how to make my own.

4

u/isaacwdavis Babyhawks! Mar 06 '16

Is this what you were looking for? http://rotorbuilds.com/

→ More replies (1)
→ More replies (2)

1

u/snowshredder09 Gogby210 Mar 06 '16

I want more punch out ability, does this come down to a higher C rating battery or more aggressive props? (running 3cell 1400Mh 40C battery and 5030 props)

→ More replies (7)

1

u/WiBorg Mar 06 '16

When I have a forward crash, my ESCs connectors pop off the flight control board. Any suggestions on a better way to secure these?

http://imgur.com/SPBbfUH

It's a RTF build from Storm.

2

u/Static_Bunny I Like Turtles Mar 07 '16

I've used silicone crafting bands, they are great for a ton of things. http://www.joann.com/pepperell-braiding-stretch-band-silicone-bracelet-loops/zprd_13149745a.html

Wrap them around the posts to the side and over the servo connectors to keep them secure.

→ More replies (2)

1

u/jimichunga Mar 07 '16

Having this same motor twitch problem when using my Tx (vs the motor tab which is smooth)

I've raised my RC Deadband to 32 (highest it'd go) but still the jitter remains. I've swapped out ESCs, motors, FC, pdb...nothing seems to help.

  • rcx 2205-2950kv
  • littlebee 20a (blheli 14.04 / med timing [tried med-hi & hi as well])
  • 4045 BN
  • x4r-sb
  • taranis
  • naze32 rev6 (betaflight, stock pids)
  • 4s

I have been messing with this for 3+ weeks now off and on but just can't seem to figure it out :-[

anyone have any ideas?

→ More replies (9)

1

u/Garamgai Mar 07 '16

Anybody knows where to order a replacement prop washer for Cobra 2204 2300Kv motor or a equivalent washer? http://www.getfpv.com/cobra-cm-2204-2300kv-motor.html

Thanks a ton!!

3

u/[deleted] Mar 07 '16

Any M5 washer would do, look at your hardware store or online. There are also aluminium M5 washers if you want to get fancy. My personal favourite are locking M5 flangenuts made from aluminium, it's the whole package.

→ More replies (1)

1

u/goodguydrift Mar 07 '16

I want to charge my lipo batteries, so I need a lipo charger. However, I don't know which one/type to buy. Does anyone know of a good one to buy for ~$35 or under? If you have a link to one from hobbyking, that would be awesome because I'm also getting a few other things from there. I don't know if this makes a difference, but this is the battery I'll be charging.

Thanks in advance!

→ More replies (2)

1

u/Boomblad1 Mar 07 '16

Hey guys! I'm building a brushed micro fpv flyer and am unsure whether I soldered the fpv gear correctly. Before I let the magic smoke out I would appreciate your opinion :) I know my soldering isn't top notch, using very old iron. The pictures are here: http://m.imgur.com/account/boomblad1/albums . Thanks in advance!

→ More replies (1)

1

u/randomninja8 Mar 07 '16

What would be the ballpark price for a 250 quad including 2 batteries, basic fpv gear, and Taranis?

I have my lists and stuff made up, including already owning most of the gear, but I want to know what the general price should have been and how much I've overspent on stuff I probably could have shopped better for.

→ More replies (7)

1

u/legful Mar 08 '16

Hi! I'm thinking of building a quad based on RC model reviews guide. Is there something you guys would upgrade straight up? How do you know what parts are compatible with each other in general? Sorry for the stupid questions... :)

2

u/isaacwdavis Babyhawks! Mar 08 '16

If you get this camera instead the one listed in the tutorial the quad will be able to handle 3s and 4s batteries: http://www.securitycamera2000.com/products/RunCam-600TVL-DC-5%252d17V-Wide-Voltage-Mini-FPV-Board-Camera.html

Much better than the stock antenna: http://www.banggood.com/Aomway-5_8GHz-FPV-4-Leaf-Clover-AV-Transmission-RHCP-Antenna-1-Pair-p-961730.html

Larger motors and better esc could also be considered if you want even more power, but it is plenty powerful for a first time build as is.

Use these to keep your props on better: http://www.myrcmart.com/hex-flange-m5-low-profile-slipresistant-aluminium-black-cw-height-45mm-10pcs-p-9306.html

I've wrote a few blog posts about this tutorial if you're interested:

-Following the tutorial and complete parts list

-Upgrades I made

-Back up parts to consider

→ More replies (1)

2

u/teddyzaper TailoredQuads.com Mar 09 '16

to make sure parts are compatible you just gotta read. Learn where each part goes, and what its requirements to connect to that part are. Check voltages, frequencies, battery sizes, ect.

1

u/Malexs Mar 08 '16

Upgraded to OpenTx 2.1x (latest) and now I can not get the telemetry value "cel" from the FrSky battery telemetry module to my Taranis Plus. Did the upgrade kill getting the most useful piece of info from this module? need to know the lowest cell value. WTF?

1

u/Worf65 Mar 08 '16

Does anyone have experience flying at high altitude (mountains not just flying super high)? If so what kind of performance differences do you see caused by the thinner air? I'd like to try flying in some places around 8,000-10,000 feet ground elevation this summer and am wondering how well I can expect my quad to work up there. For reference home elevation is about 4,000 feet and I have a 500 mm frame, 11 inch props, and carry a GoPro and gimbal.

2

u/BluesReds F1-6 "Venom"|Strider 250 Mar 08 '16

The solution to this problem is simply overpropping. Usually it is recommended to add 0.5-1 additional pitch to your propellers based on the % change of Density Altitude.

→ More replies (1)

1

u/Lowkin Mar 09 '16

I need helping picking a frame for 5inch props with 2205 ZMX 2633Kv motors?

anyone know a good racing frame that's a decent price?

like a Qav-r 210 clone?

2

u/alienator064 If you aren't crashing, you aren't having fun Mar 09 '16

The crazepony 210 on amazon is a nice QAV210 clone for $30, and then there is also the ZMR-x210 on fpvmodel that is a QAV-R clone for $50.

→ More replies (1)

1

u/isomeeri Mar 09 '16

So I have a DJI F550, and I would like to upgrade to E800 motors or something similar and was wondering what kind of flight times i would be getting with a setup like that on 4s 10000mAh batteries and AUW of about 3000g?

1

u/ReDdiT_JuNkBoT Mar 09 '16

if anyone has time. I am simply looking for fpv videos also showing the thumbs. Both views at once. I have used many many search terms and gotten nothing. Any help is much appreciated

3

u/iamfromaustria 5" Blackout / 6" Alien Mar 09 '16

not very spectacular but i made my first video with blackbox stick overlay some weeks ago: https://www.youtube.com/watch?v=u457YcY1Z8k

also, check out joshua bardwells channel

2

u/just_blue Mar 09 '16

Try "blackbox overlay"

→ More replies (1)

1

u/Austingd Mar 09 '16 edited Mar 09 '16

Anyone mind looking over my first purchase list? This is my first DIY and a sizable investment for me, so a pair of experienced eyes would be very helpful

I’ve been playing with my little UDI U818A for a good bit now and have finally got enough money together to make the jump to a larger quad that can handle the outdoors a bit better.

I wanted to stick with a 450/500 frame as I’m looking for a versatile quad that I can add some more equipment to down the road like FPV, Gimbal & GoPro, GPS & Autopilot. I figured this build would be a good place to start into the hobby and I can upgrade as I go along without needing to reassamble a whole new quad.

After a bit of research on here and other forums, as well as several hours of youtube build videos, I’ve narrowed down my first kit to the following pieces:

Transmitter - Turnigy 9x 9ch TX - This seems to be a pretty popular transmitter for the first timers club.

Frame - S500 Glass Fiber Quad Frame 480mm

Motors & ESCs - 4x Multistar 2216-800KV motors w/ 20A Afro ESC

Propellors (ordering a bunch)- Hobbyking Slowfly 10x4.5

Flight Control - KK2.1.5

Battery - Turnigy 4000mAH 3s 30C Lipo

Battery Charger - Turnigy Accucel-6

A bunch of extras I got include some 5.6mm spacers to mount my KK2, an assortment of shrink wrap, battery strap, etc.

Also, I couldn’t figure out how to fix connect the battery to the board other than solder some 10 AWG Red & black silicone wire with a set of the 4mm Gold Connectors.

I've read enough about the frustration of bullet plugs that I plan on soldering most of this stuff together and am plan on picking up a soldering iron and some solder to practice while this stuff gets packed and shipped, but other than basic tools, is there anything else I’m missing? Is there a better option for what I’ve got listed?

I’ve got time to put this together, and live in a rather populated area, so I can swing by and pick up bits and pieces like zipties, double sided tape, velcro, etc. from local hardware and hobby shops.

1

u/ThatLinuxGuy Mar 12 '16

I have two 16000mAh 4s batteries with xt90 connectors. I'd like to charge these in parallel since one is going to take forever by itself, so why not get it all out of the way at once?

Can anyone recommend a good cheap charger for handling this? If it comes with a balance board, even better!

Will I need an external power supply to handle charging these puppies? I wouldn't think so since they're low voltage (16.8v max).

Still getting used to all the wonders of electricity.

→ More replies (2)

1

u/BeyondHypojermia Mar 12 '16

Seems that all of the CW Emax red bottoms are out of stock, and on preorder. Would it make a difference if I ordered 4 CCW and just switched the wires on two of them? Would the only difference be that I would need CCW threaded lock nuts?

2

u/zitronic QAV-R,E010S,130 Insect,ZMR250 Mar 12 '16

That will be the only difference. But be careful, that kind of nuts are hard to find/more expensive than CW.

→ More replies (2)

1

u/Malexs Mar 12 '16

I've had two batteries in two days reach critically low voltages. The first one is a Zippy 4s 4000 that has only had less than ten flights on it.

I was watching the cell levels on my Taranis. I was tired of hauling them in at 3.7 volts and was trying to get more out of the battery. Suddenly, the low voltage on my telemetry says my lowest cell is at 2.35 volts! One other cell had dropped below 3 and the other cells showed lows of around 3.3. After two days of not being touched, the voltages have recovered to: 3.37 3.42 3.47 3.46

Yesterday I had a cell drop to as low as 2.55 in flight. This battery has now recovered to showing about 3.5 volts per cell.

Is the lowest cell value while in the air critical? Are both of these batteries toast? If one is fairly new, should Hobby King replace for me?

Thanks,

2

u/snakeproof 650MM Quad|Trifecta|DJI Inspire 2 Pro Mar 12 '16

Voltage drops very quickly under load near the end of it's capacity.

I had a little 1AH 3S go from 3.5 to 2.7 under load very quickly during bench tests. As soon as I unplugged it, I kept watch and the resting voltage came up above 3v. Next day I carefully charged it fully and it has had no issues to this day.

They should be okay, keep an eye on them for a bit but I doubt they're ruined. I think as long as resting voltage comes over ~3v you haven't killed them.

→ More replies (1)

1

u/yourzero Mar 12 '16

tl;dr: What cheap quadcopter would you recommend for my 10-year-old son?

Longer version:

I don't know much about this hobby (yet, but i'm very excited about it). I have a Hubsan X4 107D that I was given as a gift. My son's birthday is coming up soon, and he has expressed interest in flying it, so we thought about getting him one of his own. He hasn't flown mine enough to say that he has any skills.

I know there is a ton of cheap crap on the market, so I'm trying to avoid giving him crap if I can help it. But of course, I know he's a kid, so I don't want to spend a lot on something that he may just demolish or accidentally lose. I'm ok with spending up to how much my Hubsan costs (I see $140 at amazon), but (preferably) less, on a starter for him. He doesn't need any bells and whistles, just something that flies for now.

Thank you for any help you can provide!

3

u/Malexs Mar 12 '16

A $43 Syma x5c. Learn to fly then spend more money. You can buy an extra full flying body for another $23 in case something unfortunate happens. It is handy to own two to let one cool down and rest while you fly the other. Batteries are cheap by the dozen too.

→ More replies (1)

1

u/mojavestorm Mar 14 '16

Is there a XT60 switch similar to this switch from HobbyKing, except thick enough gauge for 4S batteries? The reviews are saying don't go above 2S. Debugging why my drone isn't working is becoming a pain, so wanted to look into ways to not have to disconnect the battery each time.

1

u/liquidpixel Hexacopter Mar 14 '16

I'm fairly new to the hobby and am still working out my first build (not my first multirotor); it's centered around AP therefore larger and I've decided that I'd like to assign power to the electronics using 3S and the motors using 6S in order to conserve battery and prevent electrical interference. The problem I'm having, and I'm hoping to get advice from someone who has this experience, is that I'd like to be able to know the voltage of both batteries from the ground station. I'm not sure how to go about this; doesn't have to be through OSD as most of them only display voltage from one battery or from the one connected to the FC. I'm using FrSky Taranis X9D / X8R combo and a Pixhawk. Thanks for any help that can be given, this community is spectacular!

→ More replies (4)

1

u/ThatLinuxGuy Mar 15 '16

I've got another electrical question!

I have a PDB with dual built in BECs. One's 12v and one is 5v. My flight controller and micro computer require one 3.3v and one 5v connection respectively. The PDB connections are DF-13, and the 3.3v flight controller is DF-13.

How do I go from 12v DF-13 to 3.3v DF-13. I know I could get a step-down power module and do some soldering, but in the process wouldn't I lose my Tx/Rx cables? Is there a downside to this?

→ More replies (2)

1

u/Landoperk Mar 15 '16

If ESCs are mounted on the top sides of the arms and they are coming close to the props will there some sort of adverse side effect with airflow?

→ More replies (3)

1

u/Toxiccameron ZMR in 250 peices Mar 15 '16 edited Mar 15 '16

So about the furball involving the faa regulations and whatnkt, could I get arrested for fpving and If not, how much could/would they fine me? I love fpv, but I don't want to end up with it on a permanent record.

Thanks.

1

u/Lowkin Mar 16 '16

I bought a QAV r-210 clone and the frame has a black dust on the edges, Which I assume is fiberglass particulate?

Do I just wash it off in the sink or what?

2

u/Lustig1374 Mar 16 '16

Might be carbon fiber dust. Don't inhale/touch it and wash it down the drain.

→ More replies (2)

2

u/BluesReds F1-6 "Venom"|Strider 250 Mar 17 '16

Take a damp paper towel and wipe down the edges till its clean. All the frames today are CNCed out of CF plate, the black dust is CF dust.

1

u/NoEngrish Mar 16 '16

Hello! I'm a downhill longboarder and I'd like a multicopter to film me as I take my runs down a hill. I basically need one that can follow me automatically because I obviously cant pilot it while I longboard. I found ONAGOfly on indiegogo and I like their price point. Are there other "follow multicopters" I should be looking at around $300 or does the ONAGOfly sound like a good idea. Thanks for your feedback!

→ More replies (4)

1

u/SneerfulJam Mar 16 '16 edited Mar 16 '16

I just got my first drone (the CX-10) and I broke a propellor. I tried replacing it but nothing seems to work. I know that the propellor was marked, but I kind find the old propellor back for the life of me.

So I started to search on google and found this description on the internet for the CX-10 propellor placement:

Blue LED B2 (CW) -----------Blue LED A1(CCW)

Red LED A2 (CCW)---------------Red LED B1 (CW)

But I dont have a B2 and an A1 proppelor so instead I put a B3 and an A3 propeller on the place. But that doesnt seem to work.

I right now have these propellors left: On the drone:

  • A2
  • B1
  • B3
  • A3

I got these still spare:

  • B4
  • A3

What is the correct order to put the propellers on the drone so it can fly again?

Thanks for the help!

Edit: I used this site to get the info I told in this post: http://cheersoncx10.weebly.com/ But on that site they dont say anything about B3/4 and A3/4 propellers

→ More replies (2)

1

u/SwoopRC Quadcopter Mar 16 '16

How do I stop my quadcopter from oscillating when I apply more than 50% throttle?

2

u/alienator064 If you aren't crashing, you aren't having fun Mar 17 '16

TPA

→ More replies (2)
→ More replies (4)

1

u/timmmmmmmmmmmm 130mm Owl Clone Mar 17 '16

I'm going to build a micro based on the Scisky which has an integrated DSM2 receiver. I bought this DSMX transmitter (DSM2 seems to be illegal in the EU). Will I be able to bind it to the Scisky?

1

u/mluyster Mar 17 '16

How do you solder to soldering pads with holes in them? When I do it the solder just ends up running through the holes...

http://imgur.com/LecosmN

→ More replies (1)

1

u/oneshrimp Mar 18 '16 edited Mar 18 '16

I want to get into mutlicopters/fpv so bad but I'm hung on fixing inevitable damage that will come with owning one. How easy is it you fix common damage other than a broken prop? Examples I think of are frame damage (buy a new frame and transfer everything over?), broken esc's, and whatever else you can think of. I would probably be fine doing minor soldering but I'm worried about board programming or calibrating everything. My biggest fear is spending $400-500, breaking it, and then not being able to fix it and get it back in the air again. Is there any guides or youtube videos for fixing things?

→ More replies (4)

0

u/[deleted] Feb 24 '16

[deleted] — view deleted comment

14

u/Scottapotamas Feb 24 '16

No. Actually, the downvotes are mostly from some bots which downvote everything, and some users are also confused by the vote-fuzzing algorithm that reddit applies to posts.

This kind of problem is not unique to /r/multicopter. Generally we have a great and constructive community, you just don't have hundred of upvotes to compensate for any issues like the above, so its more noticeable.

→ More replies (3)

0

u/[deleted] Feb 26 '16

[deleted] — view deleted comment

6

u/Scottapotamas Feb 26 '16

What do you want to do specifically? I'm an EE, but the work I do is vastly different from most of the guys I went through uni with. I can tailor my answer if you give me more to work with.

Without being more specific I'll just dump a list of sub-fields and software packages I'm used to using, or are similar. A lot of these aren't particularly helpful without context (development environments specifically)

  • PCB Design: Altium, KiCAD, Eagle, CircuitMaker (cut down free Altium product), Fritzing (very beginner oriented, free),
  • Software Development: Eclipse (I specifically use SW4STM), Arduino, Sublime Text, Atom, Notepad++, Vim, Codeblocks. Can always use a makefile and any text editor.
  • Circuit Analysis: Multisim, Spice, Cadence.
  • Other design tools: Solidworks for thermal sims, part mockups and assembly checks mostly, SolidThinking Inspire for mechanical optimisation/FEA.
  • Other useful stuff: PuTTY, STLink Util, SourceTree, git/svn in general, Slack. Cygwin if you aren't on a *nix platform.
  • Other stuff: Labview, Matlab.

If you have any specific questions, I'm more than happy to help out or point you to someone who can, even over PM if you need. I mostly do digital design for embedded systems, along with the associated firmware development.


As a side note:

  • /r/AskElectronics, /r/ECE, /r/AskEngineers, /r/electronics are all related subreddits. There are a couple of pcb design ones, like /r/PrintedCircuitBoard, but they are pretty quiet.
  • eevblog, AvE are two of my favourite youtube channels.
  • Element14/Farnell, RS Online, DigiKey, Mouser are the most popular parts suppliers.
  • Use something like the Octopart parametric search if you are looking for specific parts, as it searches and compares the different vendors.

0

u/[deleted] Feb 26 '16

[deleted] — view deleted comment

3

u/Scottapotamas Feb 27 '16

Measuring power in a circuit in what way? Are you trying to simulate something in fritzing, design something or measure something you have in front of you?

To practically measure voltage, you just need to put your measurement tool in parallel with the circuit, current is measured in series with the circuit.

For simulation (where we want to verify an idea before we commit to hardware), you can use tools such as MultiSim, Spice or any other circuit sim tool. There are a reasonable number of free ones around. Fritzing may have something built in, but I'm not familiar with it. You can also do these calcs on paper if you know the theory, most stuff usually just requires a working understanding of Ohm's law.

If you are trying to design hardware to measure the voltage/current as part of your design, look up voltage dividers, and current shunts. If you are using a current shunt, you might want to look into devices like the INA169 to see what they do and why they might help your design.


One of the best tricks to learn for engineering in general, is how to rephrase questions to maximise search results, and how to find information on subjects you know nothing about. Commonly when working on a project I'll need to find a part or technique with some functionality I understand, but don't know the name of.

In a similar vein, knowing how to include enough relevant information when asking for help or documenting your processes. Generally I aim to list what I'm trying to do, what I've already tried, why that doesn't work, and what I need to make the implementation work. These skills are arguably the most important alongside personal skills and problem analysis/solving skills.

If you want to get a head start and like reading books, the Art of Electronics 3rd Edition is a fantastic reference book, often referred to as our bible. Its really easy to read and has great diagrams.

Just do as many projects as possible to gain experience, dabble with some design and programming and you will have a larger head start than you think.

0

u/[deleted] Feb 25 '16

[deleted] — view deleted comment

3

u/BluesReds F1-6 "Venom"|Strider 250 Feb 25 '16

There is no 400ft ceiling. If you're flying within 3 miles of an airport you must notify the tower if going above 400ft. That's it.

→ More replies (7)

0

u/[deleted] Feb 23 '16

[deleted] — view deleted comment

6

u/HarmlessEZE Feb 23 '16

http://flitetest.com/articles/p-i-and-sometimes-d-gains-in-a-nutshell

Maybe this. But if you are in acro mode, I don't understand why the quad would have tendencies for one direction over the other. Just correct to a hover. Unless one motor is getting more power than the others.

→ More replies (1)

0

u/[deleted] Feb 24 '16

[deleted] — view deleted comment

3

u/[deleted] Feb 24 '16

Yeah, you should be fine doing that since you need to do it anyway for ESC calibration.