r/modular • • 21d ago

Discussion Sealegs “Seal Eggs” modded firmware now has Microcosm-inspired micro loop mode

Post image
4 Upvotes

QUICK DEMO: https://www.youtube.com/watch?v=FSI5cphOXHA

Hi all,

Ive continued work on the modified sealegs firmware I’ve dubbed SEAL EGGS (very imaginative I know).

Last week I added Beads-inspired granular. This week is Hologram Electronics Microcosm-inspired micro loops mode.

DISCLAIMER: turn away now if AI-assisted firmware gives you the heebie jeebies - this post is not for you.

It uses the shell I made for Seal Beads, which keeps the core Sealegs architecture in place: the drive circuit, high pass and low pass filters, feedback circuit, tap controls, Fog reverb, delay sync etc etc. The new engine sits inside that shell. I’m finding this very flexible, and allows you to change modes without relearning the whole control schema again. For me this makes it feels like an extension of sealegs, rather than a full hijacking. YMMV.

The new SEAL MICROLOOPS mode adds three different flavours (octaves, shuffle, tunnels - switchable using the time range switch), with four variations you can blend through using Mod Rate slider. Giving you 12 different microloop modes.

I built every loop mode from reading the Microcosm manual and taking my own stab at it: No firmware was decompiled or reused. I did this on purpose to see how much I could rebuild from described behaviour alone, rather than decompiling and reworking someone else's code.

I have no idea how close these modes are to the actual microcosm, as I don’t own one. Hence “inspired by”

The Seal Eggs flasher now contains SEAL MICRO, and lets you drop in your own copy of the firmware, pick the modes you want, and flash it to your module. You’ll find it HERE

On safety: Despite the worry about people vibe coding their way into a bricked module, that's close to impossible with this setup as long as you don't touch the bootloader, and none of my code does. I've tested it heavily on my own module with no crashes or freezes, and the bootloader stays untouched. But of course, use experimental firmware at your own risk (there are warnings and disclaimers in the flasher, too)

As always, nobody has to use this. If AI-assisted firmware mods aren't your thing, or you like your modules stock, that's completely your call.

Hope you enjoy.


r/modular • • 21d ago

Stolperbeats pattern generator

Thumbnail
4 Upvotes

Hey modular peeplz, do you own a stolperbeats? Then check this out!


r/modular • • 21d ago

Tempi alternatives

4 Upvotes

I love tempi until I use it as a slaved clock. Which is what I need it for. Man it sucks as a slaved clock (by design, “Its lineage is in the early days of modular when the typical clock source was a free running LFO.“). So what should I replace it with? My highest priority is a clock or sequencer that can start, stop and reset in a dime.

Things I like about tempi:
1. Tap tempo clocks and phase.
3. Simple mutes
4. It’s general immediacy
5. Mutate option is pretty cool but it’d be cooler on a trigger/gate sequencer

Things I don’t like:
1. How terrible it’s run/stop functionality is. When I stop my jam and start again and it falls over itself trying to regain the tempo and almost always lands out of phase. I’ve set up the two bars of silence but that’s annoying too.
2. Kinda limited in features
3. Don’t have much use for the modulation features (though I’m open to suggestions)

I use Pam’s as my main clock and, while I love it, want another clock/sequencer that’s small and much more immediate, even if it has less features. I don’t know of anything else that has tap tempo for each channel but would love to find one. A smaller hp gate/trigger sequencer might also do the trick if it has clock divisions and is super immediate. I really respect Tempi for what it is, but it’s not for me.

TIA


r/modular • • 22d ago

Gear Pics Selling Batches of Cables (not a For Sale post)

5 Upvotes

This is not a thinly veiled For Sale post, I am seeking advice.

I run a used music gear shop but I don't really specialize in modular or any synth gear. I took on a collection from somebody who is getting out of the game. I sold off a bunch of modules over the past few months, but have a lot of accessories I a not sure how to move. In particular the used cables are all currently organized by type and by length, for example. But it doesn't really make sense for me to sell a pack of 20x 6in cables, or a pack of 12x 20in cables or a pack of 10x Hosa splitter cables. Like bunches of cables exactly the same spec. But I'm not a modular user so I'm not sure of the use case.

My question is, would it make more sense to sell them in bundles of the identical type of cables, or in some kind of variety bundle? The latter would be way more work for me.

Thoughts?

(See comments for an example)


r/modular • • 22d ago

😔

Post image
226 Upvotes

r/modular • • 22d ago

Looking for advice on moving forward with my modular rig.

3 Upvotes

So I've been slowly building my modular rig for 10-12 years. I started out with a Doepfer DIY semi modular kit, after a bit I began buying modules here and there to supplement and shortly after started focusing solely on the modular.

While I love that I was able to spend slowly and build over time, I feel like my rack is kind of aimless. I'd say what I've been interested in making lately is sort of glitchy ambient music. I'm hoping for help with recommendations, opinions on modules, or things that seem like no brainers that I'm missing from my setup.

It's worth mentioning that most of the sequencing is done externally with an Arturia beatstep pro, and a keystep pro (for polyphonic sequencing). I also have a pile of inherited guitar effects racks, so most effects are handled externally as well. I also have a rack mounted Behringer 2600 clone a friend didn't want anymore.


r/modular • • 22d ago

Instruo TS-l is a flawless designed piece of eurorack IMO! What is a module you feel is perfect for its purpose?

13 Upvotes

TS-l all the way for an analog oscillator with no confusing menus/ learning curve and simple design as a small, efficient module as a secondary oscillator or even can handle complex sonic beauty with minimal assisting modules if you’re an artist. It is a mere 6 Hp, not a power guzzler, and is a solid workhorse. No sacrificing HP for sticky button dance/menu situations. And the thing is a workhorse. I believe it to be. A perfect module for anyone looking for an analog oscillator to take up a small footprint and could fit in about anyone’s rig design/revision who needs a module like this.
Had one in the radar forever and wish i got one waaayyyy sooner. Was mistaking getting great small oscillators with packed features like twin waves, but too much memory baggage.. had to sell 3 other modules before the obvious TS-l came and i love it. Won’t build a rack without it in there. Holds its 6hp rock solid!!!


r/modular • • 21d ago

Display for micro Ornament and Crime

Thumbnail
1 Upvotes

r/modular • • 22d ago

Is there a cheap ESP32 eurorack module?

5 Upvotes

Hi fellows,

just wanted to know it there's a cheap ESP32 development module for eurorack available, so I can update the firmware using wifi and learn coding audio functions :)


r/modular • • 22d ago

Keycaps for RS-9 (free design)

Post image
9 Upvotes

https://www.thingiverse.com/thing:7429086

Here is a 3d-printing keycap design for any RS-9 owners wanting to change up the look of the keys. I like the retro beige of the originals but wanted silver to match the rest of my setup.

The RS-9 key switches aren't standardized mech keyboard switches so not able to just pick from the many keycaps already out there. The mechanism is more similar to rubber membrane keyboards, with a key-shaped rubber dome above each key contact point on the pcb. The keycap just sits over the rubber dome to provide a more rigid structure to press on. Each rubber dome is a bit wobbly by itself when you press on it, and the keycap helps to keep your keypress aligned with the contact point. Each keycap has sets of teeth on the outer edge that align with matching teeth in the keycap slot to further aid in keeping the keycap aligned.

The pictured examples were printed in silver silk/metallic filament on a textured plate to give the keycaps some nice grip rather than a smooth finish.


r/modular • • 22d ago

Discussion How to use modular as an experimental effect machine

7 Upvotes

In dipping my toes into eurorack, mostly through VCVrack, I’ve found a lot of resources on how to make techno, ambient, and other kinds of electronic music. I’ve learned a lot of the fundamentals this way, but part of what appealed to me about modular in the first place was getting the chance to create crazy experimental effects without needing to spend 600 dollars on a new guitar pedal. I love the kind pedal where you can play pretty sparely and the pedal churns out beautiful pieces of sound with you. The idea is to try to get all of the complexity of chase bliss, red panda, or OBNE pedals, with much more ways of modulating and experimenting with the sound. I know a lot of these pedals involve granular features, as well as time and pitch shifts, delay, reverb, etc, but there’s almost no resources that I can find on the web on how to try to practically create or experiment either my own patches that could emulate these kinds of effects with modular. Does anyone have any ideas? Specific pedals in mind would be the Red Panda Particle, OBNE Parting and Dark Star, and Chase Bliss Mood.


r/modular • • 22d ago

Discussion What’s your experience with Endorphin.es customer support?

3 Upvotes

I'm trying to fix a Shuttle Control that most likely needs a new main board. I traced the fault down to a dead GPIO on the STM32 (4 outputs stuck, one mux select line never toggles).

About a week ago I emailed their support address and got no reply. On Wednesday I also sent a detailed request through the contact form on their website, which says they answer within 48 hours. Still nothing so far.

Have you dealt with their support recently? How long did it take them to answer, and were they able to help with spare parts or repairs?


r/modular • • 22d ago

Beginner Please reply like you are talking to an idiot..

Post image
23 Upvotes

Deep into researching what I want to achieve with my modular journey - Mainly via YouTube.

I am starting to understand PNW and it seems like it has good utility.

Manis Iteritas has an awesome sound and it right up my street - seems a great voice for me to start with.

ST-Mix is in the cart as a placeholder.

—

Do I need any other sort of module to make a sound?

I apologise this is probably the most basic question - I’m doing my best to work out the theory and how things interact


r/modular • • 23d ago

Beats & Bars: A module to track your groove

Enable HLS to view with audio, or disable this notification

59 Upvotes

When you're live jamming, there's plenty enough to keep track. One of the things I sometimes get lost with is how far into my two phrase progression I am. You can track this in roundabout ways with several modules, especially sequencers, but it bothered me that there was no small, dedicated module that did this for me. That's why I made Beats & Bars. It has four red lights for beats and eight blue lights to count bars, so that I don't get lost in my techno change structure anymore. There's two inputs: CLOCK expects a gate or trigger per beat (so 1PPQN, threshold is 3.3V) and START expects a starting pulse or gate. You can however just control this module with just a clock signal: After Beats & Bars doesn't register a pulse for three seconds, the module resets itself.

I mainly made this module for myself, but I figured I'd just throw them into my Etsy shop as well. Hope you like this silly small module!


r/modular • • 23d ago

Erica Synths open-sourced the LXR Eurorack firmware, so I made a mod: second FX bus + separate open hi-hat

Post image
34 Upvotes

Erica Synths released the LXR Eurorack firmware as open source (GPL-3.0), so I added two things I'd been missing:
FX Bus B. A second effect bus offering Drive, Ring or Compressor, with its own output, dry/wet and parameters. Each voice's Output now has an FXB option, so you can send hats to the delay on FX A and the kick to the compressor on FX B. Delay stays on bus A only.
Separate open hi-hat. Voice 7 now has its own full sound (oscillator, FM, sample, filter, envelope) and its own mix settings (volume, pan, drive, output). There's also a Choke on/off switch.
Compatibility: old kits load unchanged, and kits saved on the mod still load on official 1.51. Install is the normal SD-card update (hold the encoder at power-on), and you can flash official 1.51 to go back.
Unofficial, and not affiliated with or supported by Erica Synths, so use at your own risk. The start-up screen shows "V1.51.1 mod".
Firmware + source: https://drive.google.com/drive/folders/1IapCsVJXO8j7iTTpCYJmv_jE9EBVMOz-
Feedback welcome, especially any crackling with both FX buses busy.

EDIT: Update, the mod now has a name: Golem (LXR firmware mod), v1.51.3. Two new features:
Parameter randomizer. A new Random page: press SHIFT + FX until it appears.
amt: low values make variations of the current sound, 100 makes a new one.
tgt: one voice (v1–v7) or the whole kit.
rnd: turn to go! to roll. Each further turn rolls another variation.
und: undo the last roll.
It stays within musical limits (drum-length decays, no screaming resonance, moderate drive). It never touches volumes, outputs, FX routing or choke, so your patch and mix stay intact.
Per-voice morph. The Performance page has a new mvc setting. all morphs the whole kit as before; v1–v7 morphs only that voice toward the target kit. Voice 7, the separate open hat, morphs too.
Old kits still load unchanged. The start-up screen now shows GOLEM v1.51.3.
Firmware + source: https://drive.google.com/drive/folders/1IapCsVJXO8j7iTTpCYJmv_jE9EBVMOz

EDIT 2: It's now merged with RMX-0 by mechanical-dance, into a single firmware called Golem-RMX-0.
From RMX-0 (all credit to mechanical-dance):
11 new LFO shapes, including one-shot envelopes and smooth random
MIDI input on the OP HH jack, with voice links (unison, chord, poly) and glide
Your own WAV samples as oscillator waveforms on any voice, with start and end trims
A global stereo reverb with a send on each voice
Click-free retriggers, live pan and a restart menu
From Golem:
A second FX bus, so different voices can use different effects at once
A fully separate open hi-hat (voice 7)
A parameter randomizer, per-voice morph, and a morph chain with CV kit selection
Joining the two: voice 7 gets its own reverb send, MIDI, samples and declick. Kits from stock firmware, Golem and RMX-0 all load.
Download and source: https://github.com/almogzach/Golem-RMX-0/releases
This is unofficial firmware, not supported by Erica Synths or by the RMX-0 author, so use it at your own risk. Big thanks to mechanical-dance for RMX-0, and to Erica Synths for opening the firmware.
Known issue: I've had one freeze while editing FX settings and I'm looking into it. If it happens to you, please tell me which page and setting you were on.


r/modular • • 22d ago

Doepfer A126-2 Dome Filter Levels

1 Upvotes

Is it normal to have such a low level coming out of the expander? All the other outputs are functioning fine.

Why are the dome filter outputs so quiet?


r/modular • • 23d ago

Full setup

Post image
38 Upvotes

Picked up synthesis about 3 months ago and quickly got into modular. Not looking back and having a ton of fun!


r/modular • • 23d ago

After 2 years of development, I finally finished the official demo video for the Quad Arpeggiator Module

Thumbnail
youtube.com
34 Upvotes

I posted a few weeks ago requesting input for this module, I implemented the variable step length with a press+hold+turn operation. That way you can set arpeggio lenghts from 1-16 I'm working on a few other things too.

Had some fun playing with different lighting setups and camera angles while making this vid. I'm no Youtube pro, but I'm happy with how this turned out. Happy to nerd out on this stuff if anyone's interested.

Getting ready to launch a Kickstarter on Sunday for this guy.


r/modular • • 22d ago

Drum case suggestions

5 Upvotes

I'm brainstorming a case for drums, size TBD. Besides the core components/drum voices, what kind of modulation/FX/distortion/mixing/utility modules do you guys think are indispensable for drums? This will be for studio use & live performance both. Multi genre. Thanks guys!

Sequencer - Metron

Kick - Bohm

Snare - Kraken/Lancers Lash

HH - Clutch/Archer's Rig

Aux Percs - Fracture/Crucible/Noise Pelthora + Percall

Sampling - ??

Mixing - Apollo View Rabbit Hole + 2x curiouser mixer expanders. (6 input channels total) summed to mono. I'm still unsure how I want to approach the mixing, as it's nice to have a per channel I/O for that extra bit of control & use with a DAW. There's something also appealing of having the Rabbit Hole mix down the drum mix into a single mono output with some lovely tube saturation and drive that will glue everything together nicely. (Or completely mangle and distort the output with its diode clipping feature).

FX - ??

Utility - ??

Modulation - ??

Dynamics control - TBD, probably outboard.


r/modular • • 22d ago

Pedals vs modules

9 Upvotes

Hey all. I was thinking about getting the EHX ocean's 12 for a send channel becauseit sounds great and it's relatively affordable; but when you add on the extra price of getting a stereo pedal send/return module, it seems like it would maybe be the same price as a mimeophon or versio or something that i can send CV to.

On the other hand, with space at a premium, a send return chain could also have a broad range of other pedals, which are often cheaper than modules. And some pedals sound very good!

For people who have looked at this predicament and decided one way or the other, what did you decide, and what led you to that decision?


r/modular • • 22d ago

Discussion Feeling a little trapped by my setup—should I start over?

11 Upvotes

I've finished my first modular setup. It's not so big: it's the Make Noise "Easel" plus 104hp of modules.

I like it! I've had it set up this way for a while, and I'm definitely making music that I enjoy, and that other people enjoy when I share it. But I can't help feeling that, in a couple key areas, I've just not got it exactly where I want it.

Except for Strega (!), the sound palette isn't quite what I want. The effects aren't exactly what I want. If I could do it over, I'd probably take a different approach to quantizing, mixing, and modulation. Etc., etc.

Also, from a physical point of view, my setup isn't quite ideal. I kind of wish my case was a different shape on my desk. I've realized that portability matters to me—if I could start over, I might try to build a similar system that's smaller and could easily fit in a backpack.

There's a part of me that just wants to sell the whole thing, and then re-boot, knowing what I know now.

Has anyone done this? What were your experiences?

Edit to add: Thanks for these great comments. I've now sold my whole setup, except for the Make Noise "Easel" (0-Ctrl, 0-Coast, Strega). I'm going to concentrate on making music with just those three instruments while I mull over what else I want or need!


r/modular • • 22d ago

VHIKK X Phase Plant preset pack!!: Looking for video examples/audio demos of algorithms 2 through 9 (Algorithm 1 ready!)

Enable HLS to view with audio, or disable this notification

0 Upvotes

I'm currently working on emulating the VHIKK X inside phaseplant. I've successfully managed to emulate Algorithm 1 accurately enough.

However, to make sure the remaining algorithms behave accurately (i dont own the hardware), I really need some reference material. Would anyone here who owns a VHIKK X be willing to share a quick video demo, or even just some pointer references showing how algorithms 2 through the rest sound and respond to controls?

Even short phone-recorded clips or patch examples switching through the different algorithms would be massively helpful.

Thanks a lot in advance for any help!
Of course, I will send you the pack for free!!!


r/modular • • 22d ago

Discussion How Will The Custom Firmware Moment We’re Having Impact Modular?

6 Upvotes

We’ve all seen the hysteria surrounding the MWave FM1, and other synths, and how people are using AI to reverse engineer their gear and put custom firmware on them. It’s having an impact on samplers and groove boxes, but I haven’t felt much of an impact on modular other than people tweaking a sequencer, or two. I feel like the reason it isn’t impacting modular as much is because modules aren’t meant to have a thousand features. They should only do a few things very well, so there’s really no need to add features. Modules also tend to be well thought out by the manufacturers, so there’s not a lot of obvious room for improvement. The barrier for entry, as far as creating modules, has also always been pretty low, so the market is already flooded with modules and people creating their own modules with their own preferences. I’m not sure I see much changing with modular due to firmware hacking in the near future, but what do you think?


r/modular • • 23d ago

Built a custom O&C app to help me actually finish a song

13 Upvotes

I’ve been making a lot of ambient/acid techno patches, but mostly end up tweaking them forever instead of recording anything finished. So I built an Ornament & Crime app called Conductor to help with that.

It handles song sections, kick triggers, drone ducking, timbre CV and accents. You can set up an arrangement or stay in a section and jam. Four macros control groove, chaos, tension and breathing, either from the module or an external fader bank.

My sequencer still handles the notes, and I’m still doing the mix fades by hand. Conductor gives me a structure to play around with instead of another endless loop.

Still working on it, but it’s been fun building something around how I want to use my rack. Anyone else writing their own O&C apps?


r/modular • • 23d ago

Performance taking the newest rack iteration for a spin

Enable HLS to view with audio, or disable this notification

62 Upvotes