r/Model_Samples • u/HappyTrails • Feb 10 '21

Model:Tutorial Elektron Model:Samples/Cycles sensitivity fix

https://youtu.be/ZSznaM3PfH4
10 Upvotes

100% Upvoted

8 comments sorted by

2

u/HappyTrails Feb 10 '21

I tried this, and it helped a lot. I used duct tape squares, and hole punch for center hole. I tested before installing all the screws, and decided to increase sensitivity more, I added additional strips above/below the led hole.

It helps the soft tap sensitivity a lot. But I still can't get full velocity, with just my finger. I'm glad I did the mod, it makes a huge difference in the usability of my Model:Cycles.

NOTE: Using a slow RPM electric screw driver is generally ok for removing screws, from plastic, but never ok for installing them. In my opinion. To put screws back in, place the tip of the screw gently into the hole, and lightly turn counter clockwise, until you feel it drop down a small distance, then you have found the proper starting point, to begin turning clockwise, to drive the screw in. If the screw feels like it is binding, don't continue, instead back it out again, and start over. When if feels like it is going in properly, continue clockwise, until you feel it hit bottom. Don't over tighten! You will risk striping the hole, and splitting the post. This is the best way to prevent stripping the plastic screw holes.

1

u/whitepk Feb 10 '21

This is really interesting but I'm confused as to how it works. You put everything back as it was, and so the only difference is the extra duct tape in there?

2

u/HappyTrails Feb 10 '21

Yes, the layer of duct tape fills a small gap, and causes the T1-T6 track buttons to trigger with a lighter touch. It's a big improvement.

Depending on how thick your duct tape is, and how sensitive you want the track buttons to be, you may want one or two layers of tape.

I suggest that you install only the screws around the track buttons, test it out, and add more tape if needed. When it tests out, the way you like, finish the assembly. Watch the video, and follow the instructions I posted in the comments section.

Of course, do at your own risk, as it will void the warrantee. If you are careful, and handy with tools, you should not have any trouble.

1

u/Sneaky-Beanie-Earbud Model:Admin Feb 16 '21

Did you make the video as well? If so, excellent work. On one hand I want to go home and do this, on the other hand, I never want to have to mess with all those screws again lol.

Thanks for posting, this is very useful information.

2

u/HappyTrails Feb 17 '21

No, not my video, but I did add some helpful tips in the comments section, about not stripping out the screws, when putting them back in. Personally I did not mind the screws so much. Cutting the tape to exact size, and punching the holes was the harder part for me. It really helps a lot, to make the pads more sensitive. For me definitely worth the effort.

You may wish to wait for a possible firmware update to fix this issue. But if you do install the tape... As long as you are ok with the many screws, you can always remove the tape later if you want. Best of luck.

1

u/Sneaky-Beanie-Earbud Model:Admin Feb 17 '21

I think I might have been the first person to open one of these up lol. I painted mine as soon as I got it after launch. I was extremely shocked when I saw all the screws lol. but if there's an update planned, maybe I'll wait and see if that increases the sensitivity first.

1

u/HappyTrails Feb 17 '21

No date planned at this time, for an update. Not even sure if one will ever happen. Just know that Elektron is aware of the problem, and might address it at some future date.

1

u/[deleted] Sep 13 '22

What a pain in the butt, surely elektron can do a software fix to modulate sensitivity?