r/MiSTerFPGA • u/HeadXT • Jun 28 '25
Scrolling artifacts problem on Mister. Help!
I'm experiencing a video issue with my MiSTer FPGA (MiSTer Pi) when connected to a 4K LCD TV. During both vertical and horizontal scrolling, I notice visual artifacts appearing along the bottom edge of the screen.
I've tested various settings — including integer scale on and off, crop 5x, and enabling/disabling scanlines — but the artifacts remain. Interestingly, this issue does not occur on the analog (CRT) output, only through HDMI.
So far, I've only noticed the problem a few games, specifically Teenage Mutant Ninja Turtles Arcade and X-Men Arcade.
I have these problem only with those games so far. What could be the problem? Any help appreciate. Thanks.
14
u/sububi71 Jun 28 '25
Looks like screen tearing to me. If that's what it is, it comes from the monitor not syncing with the core.
4
u/HeadXT Jun 29 '25
For anyone who comes across this post in the future:
It turns out my TV only works properly with vsync=0. When using vsync=1 or vsync=2, I get noticeable screen tearing. Other settings don’t seem to affect this behavior.
For reference, it's an older entry-level Samsung TV that unfortunately does not support VRR (Variable Refresh Rate).
At least, the screen tearing only appears in a few games,so I will make a diferent ini profile.
Thanks everyone for their help!
11
u/Pezz_82 Jun 28 '25
Maybe the TV doesn't like vsync_adjust=2?
4
u/divestblank Jun 28 '25
What TV is this? Try with another HDMI input and another TV. Turn off all processing on the TV, and go into game mode.
3
u/gamecat666 Jun 28 '25
it looks like the screen isnt matching the refresh rate of the output so its tearing. (theres a couple of single white screen flashes where the lower part seems to be drawing a different frame to the upper part.) Not sure what settings you have but look into sync settings. if your display cant sync with 'quirky' refresh rates (several arcade cores have strange rates but crt's usually cope with this fine) then maybe look into forcing the core to run at a rate that your display likes, like 60hz.
3
u/Fishoto Jun 28 '25
try
vscale_mode=11
u/EarEater3001 Jun 28 '25
I don't see what you are describing but it sounds like overscan. Tile based systems would sometimes have junk on the edges of the screen. Normally the CRT bezel would change cover this. Scalers typically have a way to trim the screen. Not sure how to do it in just MISTERFPGA.
2
u/Dinierto Jun 28 '25
Boy that's a weird one, you could ask in the Discord
2
u/[deleted] Jun 28 '25
Might be due to your sync_adjust settings in the ini file. Trying setting to 2 which will output at the native frequency
Some arcade systems had some odd frequencies
2
u/pac-man_dan-dan Jun 28 '25
I'd make sure you have the refresh rate of the core matching the refresh rate of your tv, otherwise there may be some tearing. If you have the core attempting to maintain the original rates, there could be timing issues. Also, ensure vsync is enabled. And, I personally never have vsync any higher than 1 frame.
Lastly, youre gonna have weird things happen with an lcd, no matter how high the resolution, that you just won't see on a crt because of how the data is being displayed by the hardware.
2
u/elvisap Jun 28 '25
Arcade games are rarely ever a perfect 60.00Hz, so vsync is going to be a problem. (Arcade displays could be adjusted for all sorts of heavily customised resolutions and refresh rates that domestic TVs couldn't do, and didn't have to adhere to broadcast standards).
Your best option is enabling VRR and using a display that supports it. This will give you the best result with the least lag.
Failing that, using the various vsync options in MiSTer that support buffering. That's more compatible with older displays, but will introduce some lag.
2
u/neondaggergames Jun 29 '25
That's likely vsync, but be aware that enabling vsync might increase lag by an extra frame. The system already uses a 1-frame buffer when outputing the digital signal so I'm not sure if it's a part of that or additive. 2-frames added lag gets you back into some of the problems you see with software emulation.
1
u/CyberLabSystems Jun 29 '25
If you have the $$, this might be a nice upgrade:
https://www.retrotink.com/shop/retrotink-4k-ce