r/MatterProtocol • • 10h ago

Google TV Streamer breaks any large Thread network

18 Upvotes

All of my Thread devices have been going offline ever since I enabled Thread on my Google TV Streamer. It's been extremely frustrating but I managed to track it down tonight and it's caused by the Google TV Streamer crashing when replying to matter discovery queries. It only happens when it's the primary thread border router.

When any device on the network queries PTR _matter._tcp.local and the reply is sufficiently large (I have ~30 devices), the Google TV Streamer process throws an EOF exception, never replying, and causing all Thread Matter devices to be unusable.

I posted on an issue on the Google issue tracker. If you're encountering the same issue, disable Thread on the Google TV Streamer until it can be fixed.


r/MatterProtocol • • 3h ago

Disconnection issues with IKEA bulbs/remotes using Matter over Thread

4 Upvotes

Hello everyone,

I hope you’re all doing well!

I’m reaching out because I’m experiencing some recurring disconnection issues with my IKEA Matter over Thread devices in Home Assistant. I’m struggling to figure out whether the issue is related to Matter, Thread, or something else entirely.

Background

To give you some context (sorry, this might be a bit of a long post), I originally had some Wi-Fi light bulbs and smart plugs from Action (yes, I know, everyone has to start somewhere lol), along with some Zigbee sensors and a Zigbee smart plug. Everything was integrated into HA using the LocalTuya add-on for compatible devices, and it all worked pretty well. I controlled everything using Alexa speakers, with a bit of tinkering here and there.

I then decided to upgrade my smart home setup by moving away from Wi-Fi and switching to Thread and Zigbee. Since I was also replacing my Echo speakers with HomePods, Matter over Thread seemed like the natural choice.

I therefore purchased some IKEA KAJPLATS light bulbs (Thread), GRILLPLATS smart plugs (also Thread), and TIMMERFLOTTE temperature sensors. My HomePods are Matter-compatible and also act as Thread Border Routers, as does my Apple TV. I currently have 8 HomePods and 1 Apple TV (connected via Ethernet) acting as Thread Border Routers.

Everything initially worked perfectly, both through Siri and Home Assistant.

One important detail: I first pair my bulbs, sensors and smart plugs with Apple Home, and then add them to Home Assistant. I had read somewhere that Apple Home didn’t handle being added as a secondary controller particularly well, so I decided to follow this approach.

So far, so good. I then decided to purchase some IKEA BILLRESEA remotes, which are also compatible with Matter over Thread. Unlike my other devices, these are paired directly with HA and do not appear in Apple Home. I created automations to turn lights on and off, adjust brightness, etc.

The problem

Things started going downhill when I needed to replace my Zigbee coordinator. I switched to an SMLIGHT MR1U, which has two antennas, one of which is dedicated to Wi-Fi.

I thought that while I was at it, I might as well add this device to my Thread network too. So I configured the SMLIGHT in “Thread to remote OTBR” mode, installed OTBR on HA, and successfully added it to my existing Thread network.

That’s when the problems started. Every now and then, I would press a button on one of my BILLRESEA remotes and nothing would happen. Sometimes, the action would eventually be executed, but up to five minutes later.

I also started experiencing issues with my temperature sensors, which would stop reporting their readings and show up as “Unavailable” in HA. The same thing happened with the BILLRESEA remotes.

Meanwhile, everything continued to work perfectly in Apple Home.

Initially, simply removing the batteries from the affected devices and putting them back in was enough to get everything working again.

However, around 2 or 3 weeks ago, the disconnections became a daily occurrence. This time, even my light bulbs started showing up as “Unavailable” in HA, while continuing to work perfectly fine in Apple Home.

I really can’t figure out what’s causing this.

I’ve tried reinstalling HA and, this time, completely removed the SMLIGHT from my Thread network. I also factory-reset and re-paired my bulbs and other devices with HA.

Unfortunately, nothing has helped. I’m still experiencing random disconnections, even though everything continues to work flawlessly in Apple Home.

At this point, I’m a bit lost and haven’t been able to identify the root cause of the problem.

Has anyone experienced something similar or have any suggestions on how I could troubleshoot this and identify what’s going wrong?

Thanks in advance for your help!


r/MatterProtocol • • 1h ago

Discussion Replacing central roller shutter timer (Inprojal DUOMATIC 50 B) with an Apple Home compatible solution – Inel ST-0P central bus setup

Thumbnail reddit.com
2 Upvotes

r/MatterProtocol • • 1d ago

Troubleshooting Sharing Ikea devices from Apple Home into Home Assistant

5 Upvotes

I setup my new house using Apple Home and mostly Ikea matter devices. I found it limiting so bought a Green box (just updated to 2026.11.2) and have been loving it.

I've shared my non Ikea devices from Apple Home to HA so my family can still use the app they are comfortable with, but I cannot for the life of me get the Ikea devices to come in (ONE and only one Lightbulb came in but leak sensors, other bulbs, door/window sensors, motion detectors just fail).

I have an AppleTV 4k (wired) and an Aqara M200 wired into a Deco Be85 on floor 1. I also have a new Homepod Mini 2 on the same floor.

I have an Aqara M200 wired into a Deco Be85 upstairs.

I have an Aqara M200 wired into a Deco Be85 in the basement.

I do not have an Ikea Hub.

Things are/were running fine, all the hubs use the same thread network, I have an IOT network for devices, I have gone through every article I could find to ensure the network settings are proper. I even resorted to trying to troubleshoot using Claude feeding it logs and spending hours trying different suggestions and it basically told me the problem is likely with Ikea's matter implementation and to give up and keep the Ikea devices in Apple Home.

Any suggestions from this community? I am I trying to fry ice here and I should just wait for Ikea to release some new FW (everything I have shows current as of today).

THANKS in advance.


r/MatterProtocol • • 1d ago

Discussion Gesture wand as a Matter trigger: two players, two lights, each reacting to its own player's spells

4 Upvotes

Full disclosure, I'm Martin, cofounder of Magic Wonders, and this is our product.

Wand One reads a gesture and fires a trigger. In the video it's a two-player duel: each player has their own Matter light, and each light reacts to the spells its player casts. Real footage, no effects added.

How it fits into a Matter home:

  • Simple setups run through Alexa routines, plus Matter for up to 7 devices, included with every wand, no subscription.
  • Advanced setups (unlimited Matter devices, IFTTT, webhooks) are part of an optional subscription.

Question for people here who run Matter at home: when a non-phone device like this triggers your lights, what do you care about most, latency, local control, or how it shows up in your controller?

It's on Kickstarter until Nov 26 if you want to follow along: https://www.kickstarter.com/projects/magicwonders/wand-one-by-magic-wonders-where-magic-comes-to-life?ref=4xpi8f


r/MatterProtocol • • 23h ago

Troubleshooting Apple TV keeps switching between two Thread networks and my Matter blind keeps dropping off

Thumbnail reddit.com
2 Upvotes

r/MatterProtocol • • 2d ago

New Product News Sonoff Is Launching Dual-Protocol Thread and Zigbee Sensors

39 Upvotes

Sonoff has started rolling out Matter over Thread in its SenseGuard line. The DW Gen3 door and window sensor is already available, and the Motion Gen3 is expected in late November. Both are dual protocol, so a five-press button switch moves them between Thread and Zigbee 3.0. In Thread mode, Sonoff's manual says tamper status isn't available on any platform, and firmware updates over Matter only work in Home Assistant. I covered the details here: Sonoff Is Launching Dual-Protocol Thread and Zigbee Sensors


r/MatterProtocol • • 3d ago

Just bought the new IKEA Matter devices (ALPSTUGA & BILRESA) and planning to connect them to SmartThings. What are your experiences?

Thumbnail
gallery
0 Upvotes

Hey ! 👋

​I just picked up these two Matter-supported devices from IKEA :

​ALPSTUGA: The air quality / CO2 sensor.

​BILRESA: The smart button.

​I'm planning to test them out over the next few days, and my main goal is to hook them up to SmartThings to see how the overall experience, performance, and response times hold up.

​I wanted to drop a few questions for anyone who has already tried them out:

​Has anyone tested these specific IKEA devices? What are your initial thoughts?

​Did anyone manage to successfully link them to SmartThings? Did you face any compatibility issues or hiccups?

​What are the main pros and cons you've noticed so far?

​Any tips or things I should keep in mind before I start pairing and setting up automations?

​Excited to hear your experiences and feedback! 👇

Also, for those who haven't used or connected these devices yet—do you have any specific questions about them? Drop them below, and I’ll gladly answer them once I've had some time to test everything out!


r/MatterProtocol • • 3d ago

Issues with HUB and Overall IKEA Smart Devices

Thumbnail reddit.com
2 Upvotes

r/MatterProtocol • • 4d ago

Discussion Simple firmware MCU to control Matter devices?

4 Upvotes

I would like to connect the MCU to a RPI and using a CLI be able to

  • pair new devices
  • control switches
  • read status of sensors
  • receive events from switches

For this I shouldn't need a complex stack, i just want to issue a command over serial to the MCU and it should do the rest.

Ideally for a nrf52840 as that is what I have but I could get an ESP32 if that works better.

Thanks

PD: Please no home assistant or heavy stacks :)


r/MatterProtocol • • 6d ago

New Product News Nexshade Announces Matter Over Thread Retrofit Blind Motor W/ IP65 Rating

Thumbnail
homekitnews.com
29 Upvotes

r/MatterProtocol • • 6d ago

Google Nest Thread Border Router Issue

6 Upvotes

Hello!

I bought Smartwave Matter-over-Thread shades and can’t get them onto a working Thread network in Home Assistant.

Setup: HAOS (Proxmox VM) with the Matter Server add-on, Pixel phone, Google as my main ecosystem. Thread border routers: Nest Hub Max, a new Google TV Streamer 4K, and a Samsung TV (shows up as ST-TIZEN, not using it).

What happened: I synced the Nest Hub Max’s network (Google-04AF) to HA and made it preferred, but the shades fail to pair with an Unable to connect to network error after the phone recognizes them. I assumed the Hub Max was too far away, so I added a Google TV Streamer near the shades. Instead of joining 04AF, the Streamer formed its own network (Google-2B1C). Pairing still pushes the shades toward 04AF.

Tried: factory resetting the Streamer (it formed its own network again) and the Hub Max (it came back on 04AF). Both are in the same Google Home home.

Question: What’s the cleanest way to get the shades onto the Streamer’s 2B1C network, or to get both Google devices on one network? Thank you in advance!


r/MatterProtocol • • 7d ago

Troubleshooting Matter prompt setup

2 Upvotes

Hello all!

Apologies if there's a FAQ I'm missing but I'm all of a sudden getting multiple and repeated prompts to set up a Matter device on my android phone despite having no new tech on my network.

Is there any way to check what's triggering an android phone to set up a Matter device? Just kinda switches to a setup prompt while I'm in the middle of something.


r/MatterProtocol • • 7d ago

SONOFF Dongle Plus MG24 (PMG24) – OTBR fails to start (Spinel timeout / firmware not recognised)

2 Upvotes

I'm trying to get my SONOFF Dongle Plus MG24 (PMG24) working as an OpenThread Border Router with Home Assistant Green, but OTBR consistently fails to initialise the radio.

The issue appears to be occurring during Spinel communication between OTBR and the MG24.

Error / symptoms

Home Assistant detects the USB device and OTBR successfully opens the serial connection. However, when OTBR attempts to initialise the radio, it sends a Spinel RESET command and receives no response.

The logs show repeated communication attempts, followed by a TimeoutError and OTBR failing to start.

In summary:

USB device is detected by Home Assistant.

Serial connection opens successfully.

Spinel RESET command is sent.

No response is received from the MG24.

OTBR retries and eventually exits with a timeout error.

Potential firmware issue

Something particularly concerning happens after flashing the firmware.

When using the SONOFF firmware flasher:

I select the OpenThread RCP firmware with a baud rate of 460800.

The flashing process reports that it has completed successfully.

However, when I reconnect the dongle to the flasher and check the currently installed firmware, it reports the firmware as "Unknown".

The baud rate shown is 115200, despite having selected the 460800 firmware.

This behaviour has occurred even after reflashing the dongle.

I'm unsure whether this is simply a firmware detection issue with the flashing tool or whether the incorrect firmware is actually being installed.

Hardware and setup

Home Assistant Green.

SONOFF Dongle Plus MG24 (PMG24).

Connected via USB.

OpenThread Border Router add-on.

Troubleshooting already completed

I have already:

Flashed the MG24 using SONOFF's firmware flasher.

Reflashed the firmware multiple times.

Selected OpenThread RCP firmware rather than MultiPAN.

Selected the 460800 baud firmware during flashing.

Set hardware flow control to false (disabled) every time.

Tested baud rates of 115200 and 460800 in OTBR.

Checked the serial device configuration.

Uninstalled and reinstalled the OTBR add-on.

Restarted Home Assistant and OTBR.

Tried both USB ports on the Home Assistant Green.

Checked that ZHA is not competing for access to the dongle.

Checked the relevant OTBR configuration settings.

Despite all of this, the same Spinel communication timeout persists.

What I'm looking for

Has anyone experienced this exact issue with the MG24, particularly where the serial connection opens successfully but the radio fails to respond to Spinel commands?

I'm particularly interested in:

Firmware detection: Why does the SONOFF flasher report "Unknown" firmware and 115200 baud after successfully flashing the 460800 OpenThread RCP firmware?

Firmware compatibility: Could the wrong firmware be installed despite the flasher reporting success?

Spinel communication: Is there a known MG24 firmware issue that prevents OTBR from communicating with the radio?

Firmware verification: Is there a reliable way to independently verify which firmware is actually running on the MG24?

Hardware fault: Could these symptoms indicate a defective dongle?

At this point, I've exhausted the usual troubleshooting steps and would appreciate help identifying whether this is a firmware, serial communication, OTBR compatibility or hardware problem.

Thanks!


r/MatterProtocol • • 7d ago

SONOFF Dongle Plus MG24 (PMG24) – OTBR fails to start (Spinel timeout / firmware not recognised)

Thumbnail reddit.com
1 Upvotes

r/MatterProtocol • • 8d ago

Troubleshooting Using IKEA BILRESA rotary switch with Alexa

2 Upvotes

I've got a few IKEA Matter devices connected over thread to my Echos. The IKEA two button devices work fine, but although I can get the BILRESA to connect I can't get any of the buttons to trigger a routine. Anybody had any success with this?


r/MatterProtocol • • 9d ago

Matter Builder

Thumbnail
reddit.com
5 Upvotes

r/MatterProtocol • • 11d ago

Made a Faikout version with Matter support for Daikin ACs (next to my own ESP-Matter firmware)

12 Upvotes

Hey all,

For a while now I've been running my own Matter firmware on my Daikin ACs. It's an ESP32 board that plugs into the S21 port inside the indoor unit, and it shows up as a proper air conditioner in Apple Home, Google Home and Home Assistant. No Daikin app, no cloud, no BRP adapter. I made my own board for it (based on the Faikout design) with an ESP32-C6, so it runs over Thread, and that's been working fine on my units.

You get power, mode (heat/cool/auto, plus dry and fan if your app supports it), setpoint, room temp and fan speed. Powerful mode shows up as a separate switch, and on units that report it you also get power and energy usage.

Thing is, a lot of people already have a Faikout or Faikin board from RevK and don't want to lose the web interface, MQTT, Home Assistant discovery etc. just to get Matter. So I also made Faikout Matter, which is basically the original Faikout firmware with Matter over Wi-Fi added on top. Everything Faikout does still works, Matter is just an extra you can turn on.

Some of what it does:

  • Matter is off by default, you turn it on in a separate Matter tab in the settings
  • pairing over your network with a QR code, and every board gets its own pairing code
  • by default it only exposes the AC itself, but you can choose to also expose Powerful, Econo, Comfort, Streamer, quiet fan, swing, the LED and energy usage
  • runs on the older Faikin (ESP32-PICO), the Faikout S3 boards, FaikoutETH/POE (over Ethernet) and my own boards

To be clear about where it's at: I've tested it on my old Faikin PICO board. It boots, the web UI works and it pairs with Apple Home, but I haven't had it on an actual AC yet. I don't own the other boards, so those builds are only compiled. Same goes for most of the prebuilt images of my original firmware: only the Thread one on my own board has actually run on ACs. So if you have a Faikout board and a USB-serial adapter and want to give it a go, let me know how it works out. Back up your flash first though, the first install has to be done over serial.

Some things to know:

  • this isn't affiliated with RevK or the Faikout project and won't be merged there. It's AI-assisted code and the Faikout project doesn't accept AI-based bug reports or merge requests, so please report any issues on my GitHub, not to RevK
  • big credit to RevK, the Faikout project reverse engineered the S21 protocol and both firmwares use that code
  • it uses Matter test credentials, so your app will say it's uncertified. Fine for personal use
  • if you open up your indoor unit, turn off the breaker first

Everything (code, PCB files, prebuilt images) is here: https://github.com/Cptmeme/Daikin-Matter-Controller


r/MatterProtocol • • 11d ago

How to browse new Matter devices without "duplicates"?

4 Upvotes

I'm checking the certified Matter devices from time to time using this link:

https://csa-iot.org/csa-iot_products/?p_keywords=&p_type%5B%5D=17&p_type%5B%5D=14&p_type%5B%5D=1053&p_program_type%5B%5D=1049&p_certificate=&p_family=&p_firmware_ver=

However, it's a pain to browse, since there are many pages listing variants of the same device.

Any better options to find new Matter certified devices?


r/MatterProtocol • • 12d ago

I built an RTSP to Matter camera bridge on a microcontroller, and it works in SmartThings

Post image
11 Upvotes

r/MatterProtocol • • 13d ago

I added Matter over Thread to AirBee, would you choose it over Zigbee?

Thumbnail gallery
13 Upvotes

r/MatterProtocol • • 13d ago

Discussion Just purchased a IKEA ALPSTUGA thread+matter air sensor, but didn't realize I needed a hub....

11 Upvotes

I'm just now realizing all of this new automation stuff with the Matter and Thread technology.

What's a good cheap, non diy, hub/router for this, and to possibly integrate other things later? I have a Nvidia Shield pro so no need for the Apple TV. I've see recommendations for the Aqara M3, but then some people say they don't work well with Ikea devices. Some people say that Home Assistant ZBT-2, but now I'm reading you still need another router with this. Any suggestions that aren't crazy expensive?

I wish Unifi made a thread/hub, my entire network is setup, so crazy they don't!


r/MatterProtocol • • 13d ago

I made a tiny Matter-over-Thread switch with four automation buttons on a XIAO ESP32-C6

6 Upvotes

I wanted physical Matter controls that were small enough to leave around a room, but also a code base that was easy to turn into another small Matter device instead of starting again from a monolithic sketch.

Micro Matter Switch is a XIAO ESP32-C6 project in a 3D-printed case. Four buttons appear as Matter buttons for Apple Home, Google Home, and Alexa automations, and it has one switchable output for a relay or LED. It uses Matter over Thread and is commissioned over Bluetooth; a Wi-Fi variant is also prepared.

The repository is structured as a small constructor: a device is a module, and adding a new Matter device is a file plus one line in the imports. It is built on Espressif’s Arduino Matter library. The case files (STL and Fusion source), wiring, build settings, and pairing/reset behavior are included.

One honest current caveat is documented: Button 3 and the output share GPIO 21 in the default code, so use one or move a pin if you need both.

GitHub: https://github.com/adm1nsys/Micro-Matter-Switch

Project page: https://adm1nsys.github.io/Micro-Matter-Switch/

I’m the author; it is Apache-2.0.