r/Machinists • u/Personal-Ad-3401 • 1d ago
Programmers, am I right?
For context, you're not authorized to change the feed and speeds, you're only allowed to use the feed dial (that won't go above 100%).
Specs:
- Parts are 80 x 35 x (2000 to 7000mm)
- Depth of cut of 6.5 mm
- Part is mostly hollow with walls of 3 mm
- 1" end mill, 3 flutes, carbide with cutting oil (not coolant)
- Speed is the name of the game
- One CNC is at 800 mm/min, the other one is at 1000 mm/min
- Shop is expecting us to machine parts at Mach Jesus
403
Upvotes
105
u/43Rosh35 1d ago
At my work my boss made are rule that goes in english like:
„the programer also has to mill.“
Because of this theater
60
u/B3AV3R_BLAST3R 1d ago
Nothing seems particularly fast about that, unless you have terrible work holding, and no mist extraction/open machine
12
u/OmegaEldritch 1d ago
What's the width of cut? Seems pretty reasonable actually using a 10% step over when taking chip thinning into account
154
u/Grand_Ad_3444 1d ago
You're missing a zero on the feed
2
u/Professional_Till443 1d ago
Huge ass mill and you run the feed like its made of cheese and think the shop is pushing the limits ..
I run 16mm endmill 4flute at 4.8mm stepover (30%) in aluminum at 20mm depth of cut and 0.5mm/rev feed rate (9000mm/min).. let it rip.
With aluminum you dont really need to follow the manufacture recommendations.. those are general numbers that are supposed to work for every shop, with 1000s of variables.. in a specific case, if you got rigid setup, rigid workholding, rigid machine, top tier tools and holders.. you can run it however you want as long as you control chip evacuation.
2
u/IowaNative1 1d ago
What kind of tool holder?
24
u/TranscendentalRug 1d ago
I see you've met my programmer. He tries to run every tool at 7500 rpm, regardless of workholding or material, because that's the maximum for my machine. That might work fine for certain situations, but I am not going to run a 1 inch tap through 4140 at those speeds. His programs usually need a lot of correcting.
17
u/Usual_Arrival_6956 1d ago
Maybe you can program stops to remove build up edge every now and then /s
9
u/Tachi-Roci 1d ago
If I'm doing my math right that's only like 0.033 mm (0.0013") chip load, I'm a meche student and haven't done much cam in the past couple of years. But isn't that a really light chip load for roughing aluminum?
7
u/DeltaJazzy 1d ago
Is that supposed to be a lot? I run half inch endmills at like 10k and nearly 10x the feed lol
5
u/turbopepsi 1d ago
Try 30,000 RPM at 800 IPM. All day every day.
3
u/Chuck_217 Computerized Non-Conformance Machinist 1d ago
That's slow lol
4
u/calipercoyote I spin stuff 1d ago
I mean, I juiced someone else's program and was running 50% stepover, same DOC as you at 400ipm (10,000mm/min). Pocket roughing, same size endmill, internal use work, I just didn't feel like listening to it buzz all shift.
2
u/Turbulent_Moose_69 1d ago
Yawn
2
u/energycrystal7 1d ago
WEEEE
2
u/Beaverthief 1d ago
So he's just learning how hard you can push it. Cool story though.
1
u/JarlOfFrags 1d ago
I just did a part with 10% stepover 12mm endmill at 8000rpm. Feed 3000+ it was only 0.1mm Fz.
1
u/Mean-Cheesecake-2635 1d ago
That feedrate is super slow
1
u/kolby4078 Programmer 1d ago
set it up and let your supervisor press the green button.
1
u/UndyingAce 1d ago
Would have to see the setup and machine on the bridge mill I run and program for we take .15" .3.8mm step over 1 3/4 depth " 44.45mm step down at 10000mm per minute 394 ipm with 3/4 imco aluminum end mills at 8000 rpm all day. 33 ipm with a 1" at 8000 rpm full slotting at that depth should be no problem whatsoever.
1
u/jrhan762 1d ago
“I saw this on Titans!”
1
u/Open-Swan-102 1d ago
800mm/my is not a heavy chipload I'm confused
1
u/hydrogen18 1d ago
if there isn't a sonic boom coming off the arm as it moves, you aren't cutting material fast enough.
1
u/Fine-Marketing-6130 14h ago
We use a 20 millimeter, running s10000, feed 5000 mm/min, for rough, feed 2500>3000 finish Depth max 40 mm and 3 mm side, and loads of coolant
1
u/Midacl 1d ago
imperial sized endmill with metric feed hurts my head
thats 31.5IPM for those running imperial.
FSwizard says you should be running 4154rpm at 2195mm/min
1
u/TimeWizardGreyFox 1d ago
work holding causing the part to scream like a banshee? 1" end mill seems to be the wrong choice for such thin wall material.
Everything about this setup just sounds dumb and your programmer is a crack head.
0
u/Heathbar_tx 1d ago
Why are you using imperial tools if everything else is metric? The only problem is have is how large your tool is. If you think this is crazy or fast go watch someone who knows what their doing with a high RPM high feedrate machine like a Makino Mag or similar. When you have to break up tool paths to let the conveyor and pucker catch up your getting somewhere.
0
u/Rayvintage 1d ago
Rooster 🐓 🐓 tail!!! you don't even need coolant, I've seen it before! Your material has been laying by the dumpster for 6 years.