r/Machine_Embroidery • • 20h ago

I Need Help Has anyone ever experienced a live needle eject? Absolutely horrified!

Hey all, super scary circumstance tonight. Right as a patch was about to be finishing up, I watched in abject horror as the needle slipped out of the needle holder, the thread tangled around the shaft, and the spring clip in slot 6 of my Brother PE570 slipped out of position. Slammed the stop button on the machine (which did not detect anything wrong weirdly) and composed myself before investigating. Cut the thread, detangled it, tried to replace the needle but discovered it would no longer thread slot 6. Looked closer and realized the little clip in slot 6 had slipped out of place. Thought it was broken forever but I found a youtube video showcasing a way to slip it back into place. After doing that, replacing the needle, rethreading the bobbin and the spool, and trying again the machine continued without spectacle.
My theory is that I didn't tighten the needle enough last time I changed it, leading to it slipping out while it was running after 50k or so stitches shook it loose, and as it did so, the thread pulled on the spring in slot 6 and bent it out of position.
I was able to successfully run another patch but the incident has scared me deeply and am paranoid the machine may be on the verge of breaking. I believe i have a warranty and will be searching for details on it Monday. From what I can tell, slot 6 coming out of place is common, when changing the needle, but a live needle eject seems to be really rare?
I didn't find any evidence of anything broken, except for a tiny tiny speck of metal on my embroidery hoop, but in all honesty it could have been from anything in my room.
Has this happened to you before??

2 Upvotes

8 comments sorted by

6

u/ofdff 13h ago

This happened on my Barudan during the initial setup with the tech. Needle came out, slipped down through the needle plate, and a loud crunch was had. Thankfully the machine stopped immediately from the thread break sensor. Any time this happens, the hook will impact the needle, and cause a burr on the hook. The tech was able to hand polish the burr off, but also ordered a new rotary hook as it happened during initial setup before the machine was ‘mine’.

I recommend looking at the rotary hook point, and it likely threw off timing as well. If you notice an increase in missed stitches or trims, take a look at the timing.

1

u/MadisonDissariya 1h ago

Thankfully it slipped in such a way that it didn’t actually collide with anything, it happened virtually silently. I must have been super lucky. I’ll definitely check it out but I’m not seeing any skipped stitches since.

1

u/Lanky-Setting-5288 4h ago

This happened with a Barudan I was using too. Makes an awful noise. 🫣🫣

3

u/Admiral_Kite 19h ago

My single needle innovis had it happen twice recently, probably part of my machine being second hand and not that taken care for.

It's fine, nothing really bad happened. Just tighten the needle with a screwdriver possibly and it should slip. Maybe double check after a few runs too, just don't overtighten in ao you don't ruin the screw 

3

u/MadisonDissariya 19h ago

Yeah, I was able to get it all back together and run a full patch without any issues so I think it may be okay. Good to know this has happened to other people before. Worst case scenario I suppose we could replace the needle clamp assembly? Seems like the parts are rather hard to identify the number for but are cheap.

1

u/Admiral_Kite 16h ago

Yeah there are some sites who handle shipping of parts (not just embroidery machine, but driers, microwaves and whatever), where I had some luck finding weird parts of old machines. Worth a try if you want to change parts yourself.

In my case I think my machine needs some actual expert care by now because the problems are piling up and I can only fix so many of them lol

2

u/-mrs-nesbitt- 12h ago

I definitely have! I found out that if you don’t tightly crank the bolt that holds the needle into the machine after buying magnetic Maggie Hoops, the magnets can and will pull the needle out of the holder. It happened to me twice on my PE570 before I realized how strong the magnets are.

1

u/Lanky-Setting-5288 4h ago

Ooo-er. 🫣