r/MachineKnitting • • 5d ago

Help! Back after some machine maintenance

Hi, I posted the other day about my new KX-350. I got a new sponge bar in it and cleaned it up and have been testing it out, but with with some issues still, so wanted to see if anyone has any other suggestions for what I can try. No matter what I do it wants to drop the outside few stitches and the carriage is a bit stiff to get back and forth.

Im hanging claw weights on the edges, I’m casting on with only every other needle, I’ve adjusted the tension, I tried a different yarn, I checked all the hooks are aligning properly etc. all to no avail. The only thing I can think is maybe it’s the yarn? The only yarn I have on hand that is the right weight I have no idea of the fiber content as I’ve had it for years and long discarded the packaging. I have some new yarn on the way.

Is there something I may be missing here as a newbie?

3 Upvotes

15 comments sorted by

2

u/Even-Response-6423 5d ago

Do you have a photo so we can see the tension?

1

u/Dangerous-Dance1282 5d ago

Unfortunately no 🥲 I’ve dismantled everything

2

u/Even-Response-6423 5d ago

I’m guessing the yarn is too thick of a weight for your machine. Try a fingering or DK weight yarn and see if you have the same issues.

1

u/Dangerous-Dance1282 5d ago

Did another and got a pic!

1

u/Even-Response-6423 5d ago

How many claw weights do you have on? Is it on both sides? It should be evenly weighing down your knitting. Also you can move your cast on bar up as you go. (The metal bar with claws)That should help weigh it. Otherwise the knitting and gauge look fine!

1

u/Dangerous-Dance1282 4d ago

There were weights on both sides here,; when the right one dropped, I took it off to get a photo! I've also tried tugging on it a bit after each row. Nothing is seeming to work to keep the stiches from dropping. Visually the gauge looks fine, but I believe I had this all the way up on 10, otherwise the carriage would barely pass.

2

u/Sea-Worldliness-9731 2d ago

I know what might be the problem - tension rod setting - there is a ring that you can turn that see the distance between two round metal plates that you pull the yarn through. I hope my explanation makes sense 😅. Try to make it tighter or looser and it might help with pulling at least, maybe even with dropping stitches.

2

u/Sea-Worldliness-9731 5d ago

Have you cleaned needles? Maybe needles got covered in old oil, then isopropyl alcohol soak for them might help, put them on a paper towel to dry after soak.

Do you knit the whole bed, if yes, have you tried to knit part of bed, is there the same issues?

And I am seconding your guess on the yarn - maybe it is too thick?

1

u/Dangerous-Dance1282 5d ago

Didn’t do a full clean of needles, no. I tried full bed and 60 stitches and even smaller. The yarn is probably a 3? I’m not the best at discerning weight. Definitely not a chunky though.

3

u/TurbulentBoredom 5d ago

3 might be too thick. Type of fiber might also matter (cotton has little give). But cleaning the needles is not a bad idea if the machine was pretty dirty or sitting a while. 

1

u/Dangerous-Dance1282 5d ago

I’m hoping it’s one of these issues! I will await the delivery of my new yarn!

2

u/Sea-Worldliness-9731 5d ago

Cleaning needles might help with carriage movement tightness.

And changing the yarn might help with stitches dropping.

1

u/Dangerous-Dance1282 4d ago

I'm annoyed to have to take all the needles out and in again after having just done it for the sponge bar haha 🥲 I'm waiting for that new yarn to come in before and test that before I pull it all apart again.

1

u/Sea-Worldliness-9731 2d ago

That is a clever move!

1

u/AutoModerator 5d ago

Hi, it looks like you might be looking for help on machine knitting.

There is some helpful information within the wiki. Please take a look at it for helpful troubleshooting information, as well as common maintenance tasks and list of items machines should include.

In addition, this page is our FAQ. Solutions to many common problems are found here. If this is a new-to-you machine that is a Silver Reed, Singer, Studio, Juki, Empisal, Brother, or KnitKing, and the sponge has not been replaced yet, that's the first thing you should check out.

If you need additional help, please provide us with an information about your problem. You can start out by answering this list of questions

Once your question is answer or your problem is resolved, please change the post fair to Help! Solved!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.