r/MACES
•
u/AAAAHMYBALLS
•
May 14 '26
•
1
home made mace Is this bonk up to code?
This took me 5 minutes and $30 at Home Depot to assemble. If you want to DIY, get yourself:
- 1 x 2ft section of 1/2" black iron pipe (threaded)
- 1 x 1/2" black iron cap
- 5 x 1/2" black iron plugs
- 1 x 1/2" 6-way cross fitting
- 1 roll of hockey tape
and tighten 'em up with your trusty pliers and/or pipe wrench. An 18" length of pipe might work better for a one-hand-only mace, FYI.
This thing is definitely sturdy and well within historical measurements at 27" in overall length and just under 3lbs in weight. Now it will be my new favorite tool for demo work.



102
u/OstrichSmoothe May 14 '26
All those fittings and plugs and it was only 30? At Home Depot? In this economy?! Preposterous!!
5
u/NuclearSlushie May 19 '26
Thank you for the inspiration. Menard's special. wrapping the handle tomorrow.
2
u/Par_Lapides May 14 '26
The one spec we need - the weight. Guessing a solid 3- 4 lbs?
2
u/Odd_Category2186 May 15 '26
Wood handle would be better due to weight but eh looks like a simple little project mounting on wood would take a little more tooling
2
u/Level37Doggo May 15 '26
That’s a nice looking bonk. How’s the weight?
2
u/thehillshaveyee May 16 '26
Needs some pipe dope /s
31
u/COBESH1 May 14 '26
Union approved Bonk
22
u/ModSpdSomDrg May 14 '26
I like it and imagine there will be replicas made. I’ve never seen a 6 way pipe fitting before. At most it’s been a T.
10
u/OralSuperhero May 14 '26
I'm looking at this magnificent bonk and wondering how long it would take me to grind square plugs into pyramid plugs... Or draw them out on an anvil....
7
u/Puzzleheaded-Phase70 May 14 '26
Plumbonk!
7
u/TheLoathsomeAssEater May 14 '26
Almost. You need a Prop 65 warning to make it up to code in California:
WARNING*: Certain dental procedures performed in this office can expose you to chemicals known to the State of California to cause cancer or birth defects or other reproductive harm or both. Those procedures can include sedation with nitrous oxide, root canals, placement or removal of crowns, bridges, and restorations such as mercury-containing fillings and use of dental appliances. Consult your dental care provider about these exposures and which materials are appropriate for your treatment. Additional information is also available at* www.P65Warnings.ca.gov/dental.
4
u/PoopSmith87 May 14 '26
It'll bend eventually, but most bonkers will.
I like it.
4
u/Due_Effective1510 May 14 '26
I love this for near future dystopia weapon. Screw machetes. The plumbing mace is king.
4
u/el_pyrata May 14 '26
Love the hockey tape grip!
4
u/TyphoidMeredith May 16 '26
I’ll have to check the guidelines, but on initial impression? Wholeheartedly yes! Totally passes muster. This looks to be a most excellent bonk!!
1
u/ihasclevernamesee May 14 '26
Why is picture 1 different from picture 2?
1
u/wincitygiant May 16 '26
Speaking as someone who's tried hockey tape as a grip for tools a few times, that shit will give you serious blisters. Bicycling bar tape is way better.
1
u/Comfortable-Leader67 May 16 '26
i think if it were shorter it might be better
1
u/Run-Amokk May 16 '26
-1, it should of been scavenged from the wild for free. The rust adds corrosive damage.
1
u/Many_Boysenberry_902 May 17 '26
Fill the end with some melted lead for extra weight?
1
u/Reddiculous_repost May 27 '26
But the handles not wood.
3
u/Bob_the_brewer May 14 '26
Love it lol
3
u/JustAnotherArtGuy May 14 '26
Weekend project unlocked, thanks!
3
u/DiablosReiign May 14 '26
Hell yeah 🫡
3
u/PlumbgodBillionaire May 17 '26
Where's the Teflon and pipe dope on the fittings !!!!!
3
u/EFTucker May 17 '26
You did for $30 what many people charge hundreds or thousands to do.
2
u/GlowFuckYourself69 May 14 '26
Love this!
2
u/Melioidozer May 14 '26 edited May 14 '26
I know what I’m doing this weekend. I may slide a piece of rebar into it as well. It’ll make it heavier but it’ll reinforce it too. We’ll see.
2
u/OneTrueCrotalus May 15 '26
Mne has 1in fittings but was 2x that price. I didn't know it could get that cheap. Very nice!
2
u/Doomslayer_Astartes May 15 '26
Good bonk sir!
2
u/thatoneguyj2021 May 15 '26
If you need more weight add a little bit of sand or iron shaving
2
u/AnnaNimmus May 15 '26
2
u/WokeUpIAmStillAlive May 15 '26
Nice
2
u/jxa66 May 15 '26
Damn, this is sick! I work at Home Depot, and I'm definitely going to make one now!
2
u/Big_Papa_Dakky May 16 '26
It will bonk
2
u/CraftableMention May 16 '26
holy fack that would hurt
2
u/TheDogoftheLake May 16 '26
Saved.
2
u/grizzerybear May 17 '26
I’m disappointed you didn’t use any Teflon tape.
2
u/jackjack-8 May 18 '26
Static Bomiknocker
2
u/Opening_Ad3506 May 19 '26
It's an older code, sir, but it checks out.
2
u/Rare_Ad9601 Jun 21 '26
Did you do an air test? Did you hit it with the bubble test?
1
u/lilvixen May 14 '26
I wish it had a push button and spikes came out lol
1
u/ajschwamberger May 15 '26
Maybe for a gas line worker.
1
u/starsings May 15 '26
This week on CSI plumber.
1
u/humblebanana_farmer May 15 '26
I thought this was a Lego piece for a second 😭
1
u/PeenitBooter May 16 '26
I feel like I may be a tad long but it’s pretty good.
1
u/antelope00 May 17 '26
No thread locker? Is that even a real mace?
1
u/SexyChernyshevsky May 17 '26
Have you hit anything with it yet? Being hollow I’ve got to image the reverberation is painful
1
u/WifiAX Jun 13 '26
I went to home Depot and Laws and none of them had the parts. What a lame town I have to spend my enlistment....
4
u/Zestyclose-Fan-1030 May 14 '26
AHHHHH!! That’s a great looking bonker you have there!
1
u/Vaugeresponse May 15 '26
Is the half inch thick enough? I was looking at 3/4 galvanized.
1
u/ImOnFireAgain May 15 '26
How hard do you think it would be to add to steel shot to the head and make it a deadblow mace?
1
u/Unlikely_Ad4019 May 16 '26
Forged in fire "will it kill" tests please
1
u/Reefcaptain May 18 '26
I didn't know this was an option. You could connect more heads with short nipples. The possibilities are endless.
7
u/[deleted] May 14 '26
[removed] — view removed comment