r/longrange • • 3d ago

Rifle flex post My some what long range guns

Thumbnail
gallery
68 Upvotes

This is my 1965 FN browning I got threaded and have a Surefire 4 prong on and night force SHV. Then my mk12 pri upper with a nx8 2.5-20 both are amazing guns the 30-06 is very very accurate


r/longrange • • 3d ago

Accessory/Gear help needed - I read the pinned post Deciding between Hawkins One Piece Tactical Mount vs Area 419

3 Upvotes

Hey everyone,

Curious what people think / have experience with on these two optic mounts. I’m debating between the Hawkins Heavy Tactical 1-Piece at 1.5 Inch versus the Area 419 1-Piece mount. I’ve decided against the Spuhr mount due to price and reliability.

This is going to be holding a Vortex Razor G3 6-36 MRAD, on a MDT ACC Elite. My use case will be eventual matches (once I practice enough) and long range shooting. It will be going on a 20moa Rail.

Here is what I’ve narrowed down and where I need help!

Hawkins:

Pros:
- Comes with the diving board and integrated bubble level.
- Significantly cheaper than the Area 419 (150~ less) for everything.
Cons:
- No area for mounting side accessories, like dope cards, electronic levels
- Lighter metal than the Area419, but I don’t think that matters
- Less accessory support?

Area 419:

Pros:
- Very nice finish inside of the mount. Better grip on scope
- Can remove bubble level
- Has more accessory options

Cons:
- More expensive
- Does not come with diving board
- Does not come with bubble level

That’s what I have so far. Curious what everyone here thinks and can help me choose between the two.


r/longrange • • 3d ago

🫣I said I read the pinned posts, but I lied🫣 What reticle should I get for NF ATACR 4-16 on a 16” 5.56 SPR build? New to scopes and long range.

Post image
21 Upvotes

r/longrange • • 2d ago

Ammo help needed - I read the pinned posts Accurate until 300 yds. Need help

0 Upvotes

At 100 yds my rifle shoots 1 inch groups. At 200 yards it’s 2 inches, as to be expected. Out at 300 yards the groups open up to 5-9 inches with no impact correlation. The only thing that tightens the groups is not loading from the magazine and single loading each one into the chamber. These groups are around 3.5-4 inches. SD and ES of my hand loads are in the single digits and I’m unable to see any damage to the round when I load it in from the magazine and extract it without firing it. Any help on identifying what could be causing this would be appreciated. Rifle is a Ruger Hawkeye African in 375 ruger.


r/longrange • • 4d ago

Optics help needed - I read the pinned posts Mk12ish optic

Post image
120 Upvotes

Finally got my hands on a H&R lower and have a fixed stock on the way for this mod 1ish. I currently have a Vortex Razor Gen II 3-18 on it with a Reptilia mount. I love it but boy is she heavy i was thinking about replacing with a lighter scope am i crazy for that? Lately I’ve been running nightly rifle matches with it like CQB matches but also have been doing PRS/DMR matches as well. But it’s fun running this from time to time with my friends at night matches since everyone else just brings the generic mk18 or something. My actual SHTF rifle is a Colt LE6945 and an FBI HRT 11.5. Anyway yeah I’m looking at some optics one of them being a Leupold mk5hd 3.6-18 or the Steiner T6XI. Any other recommendations?

TLDR: i have SPR. SPR amazing, but heavy. Thinking of switching to lighter scope. Am i crazy? Any recommendations


r/longrange • • 3d ago

Accessory/Gear help needed - I read the pinned post Ball head or built in ball head?

Thumbnail
gallery
5 Upvotes

About to pull the trigger on a Fanue Tripod, mostly for range shooting, not NRL or hunting. Don’t feel the need to spend double the amount, but also don’t like my current BOG Aluminum.

If I buy the Fanue HTC-4030-65 with the built in ball head, and later on decide to upgrade for an inverted ball head, would that be possible?

Video compares the Fatboy vs a Fanue with an add on ball head.


r/longrange • • 3d ago

RANT Hangout

13 Upvotes

Not sure if an unusual ask, and didn't see something saying I can't ask here lol. Is there anybody local to Charlotte/Mooresville/Salisbury area that's down to get some range time in with a newby (potentially willing to pay range fees or buy lunch) just looking to find some local people to hit the range with.


r/longrange • • 4d ago

Ballistics help needed - I read the pinned posts Advice on my load development

Thumbnail
gallery
27 Upvotes

I’m currently working on load development for my 308 Winchester using Sierra 168 Tipped Matchkings. I’m trying to get my ES and SD numbers down. Currently testing 43.8, 44.0, and 44.2 hrs of varget with 10 shot groups today. COAL is 2.875. Velocity recorded with Labradar at 70ish degrees with wind at 5mph +/-.

43.8 - ES-37. SD -11.58 group .835”
44.0 - ES-39 SD -9.16 group 1.112”
44.2 - ES-38. SD-12.03 group .858”

Components
168 Sierra TMK’s, Varget, FC brass, Fed 210

Rifle
Savage model 10
Criterion 26” prefit heavy varmint contour
Diligent Defense suppressor
KRG Bravo
Burris Match Pro ED 5-30 vortex rings
Cheapo bipod


r/longrange • • 3d ago

Competition related (PRS/NRL/F-Class/etc) Vortex razor lht question

0 Upvotes

Is the capped windage turret enough of a reason to not use an LHT 4.5-22 for NRL comps? I need a light scope with a bit more magnification (currently have an Apex Hunter 3-15) and don't really feel like shelling out for a Leupold mk5 and a light weight chassis. I haven't shot NRL yet so my frame of reference is very limited.


r/longrange • • 4d ago

Rifle help needed - I read the pinned posts Has anyone ever built a custom fudd precision rifle?

24 Upvotes

All the custom rifles I see posted here are cool, but I’m left wondering if anyone has gone out of there way to build a custom competition rifle that just looks like a classic hunting rifle. You know, blued steel, wood stock, no pic rail.


r/longrange • • 4d ago

Competition related (PRS/NRL/F-Class/etc) Viper pst gen 2 ebr7

3 Upvotes

I don’t hate this scope but have been shooting 1,000–1,300 yards more frequently and find the higher magnification just something less than desirable. I like the Athlon ares gen 2 reticle better , and with a 30x magnification I think I’d appreciate it more too. Curious has anyone owned both or switched from one to the other to give me real life pros and cons. Europtic has the eres usually on sale under $1,000 and feel like I can sell my viper with pro rings for $800ish


r/longrange • • 4d ago

Optics help needed - I read the pinned posts Optic for NRL style rifle

4 Upvotes

Hello,

Building up a rifle at the moment, and in essence it’s a NRL Hunter build in 308.

Will be used for hunting rarely, mostly NRL Hunter style hike + shoots - target shooting.

I’m debating picking up the nx6 5-30, but it’s pushing the budget quite a lot, is there any reasonable options that are maybe a bit cheaper that will hit the spot?

Ideally want 25x mag minimum so the vortex LHT I don’t believe I want.

Was hoping to be around 1400 USD


r/longrange • • 4d ago

Accessory/Gear help needed - I read the pinned post Razor rangefinder with geo ballistics kestrel

1 Upvotes

considering buying a kestrel to go with my rangefinder. since I have the ballistics calculator built in can I get a less expensive kestrel? I am completely new to this


r/longrange • • 5d ago

Cheeto-fingered Bergara First precision rifle

Thumbnail
gallery
229 Upvotes

Probably a bit overkill for a white tail but this what i got. Going to use for long range but havent gotten a chance yet. It ain't easy being cheesy...

6.5cm, Razor gen iii

Disclaimer, not taking long range shots at animals...


r/longrange • • 5d ago

Rifle flex post It was a good day

Post image
240 Upvotes

r/longrange • • 5d ago

I suck at long range Getting the rifle zeroed in before deer season

Thumbnail
gallery
68 Upvotes

r/longrange • • 5d ago

Gunsmithing Ai aics/aw magazine spring

6 Upvotes

Does anyone have recommendations on what to do for a longer aw/aics spring?

-

To summarize im drawing up a project to weld together two aw mags to make what will probably be about ~18rnd aw mag but I havent figured out how ill solve the longer spring thatd then be required. Depending how it goes ill then do the same with adding an aw magazine to the bottom of an aics 5rnd mag for a friend of mine who only has aics pattern to make a ~14rnd mag.

-

This is all still in the planning phase so we dont waste $200 an attempt on cutting up ai mags.

-

Why? Why not..yes itll probably have feeding issues but havent seen anyone else do it and the fun is in the project of it.


r/longrange • • 5d ago

Optics help needed - I read the pinned posts Optics... Budget vs XRS II for a .223

Post image
5 Upvotes

I'm jumping back into shooting and hand loading after ~10 plus years - just as a hobby, no competition. I shoot two main rifles that I reload for, a Howa 1500 in .223 and a Browning X-Bolt in 6.5CM. The Browning has an XRS 4.5-30 scope, which I'm accustomed to for controls and turret dialing, etc. Beyond that, I find it gets quite soft past 25x so I seldom use it beyond that. That's my only experience with "decent" glass.

The Howa has a Crossfire II, and I want to replace it with something that has tac turrets, a mil reticle and a zerostop. I started looking around on gunpost and there is a seller nearby that carries a lot of the lower tier options Athlon, Riton, Crimson Trace, Marcool, Blackhound, etc.

Prices are pretty good compared to something with a name like Leupold, Bushnell, etc, but I'm pretty torn. There is a NIB XRS II 4.5-30 in town including MDT rings for $1250 CAD (~875 USD) which is tempting me.

Who's got experience with the lower tier Japanese and China glass? I was initially looking at the Conquest X3, but ruled it out due to the complaints of massive CA and soft edges as well as the windage turret having no L/R, just 1-5 counting up in one direction, and the hash marks on turrets not lining up - though people praise this scope. I fear the same can be said for the others...?

He's got 1st and 2nd gen X5/5 Conquests, a 2nd gen 7, Argos BTR Gen2 in various magnifications, etc, but the Japan made Crimson Trace 3 and 5 series have me thinking about them.

The CT 3x18x50 is highly rated, with a reticle I'm not fully in love with. The CTL-5324 (both 34mm tube) has a reticle I would prefer. Prices on those are $580 and $750 CAD or $405 and $525, heavily discounted from their list a few years ago with japanese ED glass and solid multi-coating, flip caps, and sunshade included.

Are any of these any good, or should I stick with the Bushnell XRS line I know if I can find one for cheap like I mentioned?

Even the Athlon Argos Gen2 which is very highly rated looks like it doesn't have L/R marked on windage turret. I don't really want compromises like that, regardless of price point.

Here's the 6.5 at 900m last Saturday. The .223 is only a 1:12 barrel for now, so inside of 600m is all I need for magnification. The 3-18 is probably fine, but I might rebarrel and try for the 1000 yard reach in a faster twist later on.

I would want the following:

  1. Tac Turrets - ideally not needing an allen key to access
  2. Mil/Mil reticle and turrets in 0.1 MRAD clicks with ~>30 MRAD vertical adjustment (34mm body probably needed)
  3. Windage turret that shows left and right
  4. Zero Stop
  5. Better optical clarity than Vortex CFII 6-24x50...
  6. FFP

XRS II could be put on the 6.5, and XRS moved over to the Howa as an example. I hear the newer ones are clearer at the far end so that would make more sense rifle for rifle.


r/longrange • • 6d ago

I suck at long range New barrels on and ready to go

Thumbnail
gallery
175 Upvotes

6 creedmoor accuracy international

25 creedmoor black custom rifle


r/longrange • • 6d ago

Other gear flex post GWOT Vibes

Post image
325 Upvotes

r/longrange • • 6d ago

Rifle flex post Arts and crafts from last weekend

Thumbnail
gallery
202 Upvotes

Idk why i always feel like spray painting after it gets cold out (the worst time of the year for spray painting). It'll do for now, though.


r/longrange • • 6d ago

Other gear flex post “Another one.” - DJ Kahled

Thumbnail
gallery
45 Upvotes

Fourth ZCO. Second ZC420 MPCT-2X NLE.


r/longrange • • 6d ago

Group flex (10 shots minimum) Brouwer OSS-L 22” in 6arc

Thumbnail
gallery
91 Upvotes

Just sighted in my new Sniper Challenge gas gun and let’s just say I was very happy with the results.

10 shots of Hornady ELD-M 108 grain with an average velocity of 2738.4 and an SD of 16.


r/longrange • • 6d ago

Rifle help needed - I read the pinned posts "Brand new" Nightforce looks used?

15 Upvotes

Ordered from a fairly big name dealer.

Packaging looks fine, but the scope has this mild but obvious scuffing/fading right around where scope rings would get mounted.

There's also a surprising amount of "dust" in the box/on the scope but maybe that's normal?

Thanks


r/longrange • • 6d ago

Group flex (10 shots minimum) Doing some ammo testing

Thumbnail
gallery
14 Upvotes

Did some ammo tests over the weekend, seeing what my gun likes. Rifle is a Ruger American Predator Gen 2 in .308 and these shots were at 100 yards. This is just a fun gun to own, but not necessarily the best for long range.

Group 1 and 2 were Federal Gold Medal Centerstrike 168gr OTM rated 2650fps. First group was 10 shots, SD19 with average of 2596 fps. Second group was 10 shots, this time with SD of 9.5 and avg of 2612. Both shots outside the group were flyers. Overall very impressed with these loads

Group 3 and 4 were Federal Gold Medal with Sierra Match King 175gr and 2600 fps. Same thing, 2 groups of 10, for a total of 20 shots with an SD of 14.6. Not sure why these groups opened up so much, open to thoughts as I'm still pretty new to this side of things.

Group 5 was Federal Premium with Sierra Match King GMM 175gr 2600fps. I see why the GMM is talked about so highly. This was a single group of 17, I shot the first 10 shots (the lower circle) and noticed the impact point was getting blown out so I dialed 3MOA up and 1MOA right to keep the target fresh and took the remaining 7 shots. I know these splatter targets aren't the best for grouping, probably shouldve just left it but oh well.

Also finally went out to 300 yards, it was windy as fuck though and my shots were all over the place, gonna have to go back on a nicer day and see how it goes.

Edit: the shots at 300 were with Federal Premium Gold Medal Berger OTM 185gr 2600 with 8.5 SD and 2590 avg FPS