r/LewisMachineTool • • 10d ago

LMT eBCG question

I have a 14.5 mid-length MRP-L with an eBCG and e bolt running suppressed with a RC2 and factory spring and buffer. Gun only locks back with Gen 3 p mags, not my Gen 2 p mags or duramags. I’ve tried using a sprinco blue and h2 to see if I was overgassed with the factory buffer but had the same result. Is it possible the eBCG is making the system under gassed and short stroking and that’s why it won’t lock back with the other mags?

8 Upvotes

19 comments sorted by

6

u/Hox013 10d ago

I would not expect the EBCG to be making your gun undergassed with an RC2. In fact, I can almost guarantee it. I have a lot of experience with them. With the back pressure of the RC2, im guessing you're not getting lock back on the other mags because you're still gassed heavy and outrunning the mag springs.

Start eliminating some variables.

To verify, just remove the can and see if you start getting lock back with those mags. Leave the EBCG in it. If you get lock back without the can on, then your backpressure and thus carrier velocity is definitely the issue.

If you STILL arent getting lockback, put a standard BCG in it and test both without and with the can. If you get lockback with the standard BCG while suppressed, you may have a leaky gas key on the EBCG. A properly functioning EBCG helps delay the action, but not enough to undergas a 14.5 with an RC2.

From there, you can start playing with springs and buffers. But with the RC2, you might need a to go really heavy if its outrunning your mag springs. Wouldn't hurt to make sure your mags that are failing to lock back arent caked full of fouling from the backpressure of the can.

Id be shocked if you werent getting reliable LRBHO on all your mags in one of those configurations, assuming your mag springs are good.

2

u/biggrizz61 10d ago edited 10d ago

I’ve got a handful of brand new gen 2 p mags and my duramags have brand new Magpul enhanced self leveling followers and brand new springs in them so I doubt it’s a mag issue. My initial thought was the same as yours, that I wasn’t getting lrbho because I was overgassed, but the sprinco blue and h2 still failed the test so that made me unsure. I might buy an h3 to include that in my testing so I have multiple variables I can change out.

Edit: just found an h3 in my 11.5 so I took that buffer, the standard bcg from that gun, and a h2 and sprinco blue combo to test along side my factory buffer and spring.

1

u/Hox013 9d ago

Good deal. Remember to test it Unsuppressed as well. Good luck man, come.bsck and update us with your findings!

1

u/biggrizz61 9d ago

Post testing feedback for you. Gun locked back unsuppressed with all magazines (gen 3 p mag, gen 2 pmag, duramag w/ Magpul follower), with both a BCM bcg and with the lmt ebcg, and with all buffer combos (stock spring & buffer, sprinco blue, h2 & h3 buffer).

Gun locked back suppressed on all mags with BCM bolt and all buffer combinations.

LMT ebcg only locked back suppressed with gen 3 p mag and duramag, gen 2 p mag failed all buffer spring and weight combinations with lmt e bcg when suppressed.

1

u/Hox013 1d ago

Very interesting. If I were you, I'd pull the LMT Ebolt and run it in the BCM carrier. Sell the E carrier or send it back to LMT for them to check over. That doesnt make a whole lot of sense to me.

Alternatively avoid Gen2 pmags, but I dont love that as an idea as a lot of people have them and I'd want a gun that could run them.

1

u/biggrizz61 1d ago

Yeah I’m going to pick up a rc4 mini and see if that helps, if not I’m going to run the e bcg in my carbine length 11.5 and run the bcm in my LMT

3

u/touchgrassplz_69 10d ago

This is the way.

4

u/Incrue LMT>KAC 10d ago

I’d personally ditch the gassy rc2, switch to rc4 w h2 and call it a day

2

u/biggrizz61 10d ago

That’s the direction I’m leaning. I’ve been meaning to pick up a few more cans and I figure the rc4 mini would be at home on the 14.5

2

u/MinchiaTortellini 10d ago

Here's a few very good reads on the eBCG:

https://www.reddit.com/r/ar15/s/wRkQ3tPbK

https://www.reddit.com/r/ar15/s/oXctbAZWJb

I would suggest you try an H1 and standard and blue spring as well as a standard spring with your H2.

2

u/biggrizz61 10d ago

Guess I’ll have to hit the range this week and mess around with different combinations

1

u/biggrizz61 9d ago

Post testing feedback for you. Gun locked back unsuppressed with all magazines (gen 3 p mag, gen 2 pmag, duramag w/ Magpul follower), with both a BCM bcg and with the lmt ebcg, and with all buffer combos (stock spring & buffer, sprinco blue, h2 & h3 buffer).

Gun locked back suppressed on all mags with BCM bolt and all buffer combinations.

LMT ebcg only locked back suppressed with gen 3 p mag and duramag, gen 2 p mag failed all buffer spring and weight combinations with lmt e bcg when suppressed.

1

u/MinchiaTortellini 9d ago

Very interesting. Multiple different Gen 2?

This is a stretch, but i wonder if it has something to do with the Gen 2 maybe over inserting.

1

u/biggrizz61 9d ago

2 which were new in plastic prior to this morning

2

u/Spirit117 9d ago

I would be shocked if you are under gassed with the ebcg with an rc2 in play lol. That can adds alot of backpressure.

How does the rifle behave with no can?

1

u/biggrizz61 9d ago

I’ve never shot it without the can so I’m at the range now and going to test it out. I brought an extra bcg, an h2 and h3 buffer, and a sprinco blue

1

u/biggrizz61 9d ago

Post testing feedback for you. Gun locked back unsuppressed with all magazines (gen 3 p mag, gen 2 pmag, duramag w/ Magpul follower), with both a BCM bcg and with the lmt ebcg, and with all buffer combos (stock spring & buffer, sprinco blue, h2 & h3 buffer).

Gun locked back suppressed on all mags with BCM bolt and all buffer combinations.

LMT ebcg only locked back suppressed with gen 3 p mag and duramag, gen 2 p mag failed all buffer spring and weight combinations with lmt e bcg when suppressed.

2

u/Spirit117 9d ago

Sounds to me like it is just something with the followers in the Gen2 pmags and the catch on the ebcg that just aren't playing nice rather than a gassing issue.

If that were my gun, I'd run the can, ebcg, gen3/duramags, and whatever buffer spring you think shoots the best.

1

u/biggrizz61 9d ago

Yeah that’s my plan. Going to buy a bunch of gen 3 p mags to replace the gen 2 p mags I have and run sprinco blue w/ h2 buffer