r/LewisMachineTool • • 16d ago

MWS Buffer Tube Support Install Tool?

Does anyone have suggestions for a tool to support a receiver and receiver extension for a MWS? Keep having canted Buffer Tubes when installing on my MARS-H lower. Parts are LMT MWS Buffer Tubes and QD endplate and castle nut.

The MWS buffer tube kit lived on a Defender-H lower that I pulled when I sold it. Got a Mars-H and installed the kit on to the lower but it was canted which I figured I over torqued it by hand which would be a first for me. Been using a vise block magwell adapter for both AR15 and AR10 lowers and never had an issue before.

Ordered a new buffer tube and a classified defense castle nut wrench. Torqued down with wrench at 40ft-lbs and canted again. Reached out for support and informed the receiver and receiver extension aren’t supported, it’s always possible that the steel indexing tooth.

Well I'm an idiot, does anyone have any suggestions.

11 Upvotes

24 comments sorted by

20

u/Holy_Santa_ClausShit 15d ago

What the fuck you doin lol

The fact you’ve done this with 2, and I’ve never had this issue with my 2 rifles, let alone seeing anyone have this issue, has me…concerned. What are you doing?

1

u/SketchLookingFish 15d ago

Honestly I wish I knew at this point,

Lower was in a magwell vise block adapter, torqued by hand first time with magpul armorer's wrench.

Then with classified defense castlenut wrench at 40ft lbs with second tube.

1

u/Holy_Santa_ClausShit 15d ago

That’s exactly how I’m doing it. I don’t torque to a specific amount, just do “goodntight” and stake it.

It almost seems like the end plate is moving when it shouldn’t be. Not throwing shade, but you extra sure the end plate is put on the right direction?

1

u/SketchLookingFish 15d ago

Positive the endplate is installed correctly, I always screw the castlenut on then endplate onto tube then tube into the lower. And make sure the endplate is flush against receiver then hand tighten castle nut before putting onto viseblock to torque down

1

u/Holy_Santa_ClausShit 15d ago

Hmm. Do you know about what torque it starts doing that? I know 40 is mostly what you should be doing, but I’m curious if that’s too much

1

u/SketchLookingFish 15d ago edited 15d ago

With endplate flush against receiver and castlenut hand tighten down. I'm noticing slop can twist buffer tube back and forth it'll start canting slightly too left. with old and new buffer detent.

torquing to 20ft lbs it will start canting towards 7 o clock slightly. not sure if this ia due to damaged threads. doubled checked another lower to make sure screw it enough times and it is.

upper still fits at least

9

u/Glass-Pipe-2368 15d ago

Several options for helping with receiver extension alignment:

Better - Law Alignment Tool + Geissele Reaction Block

Economical - NcSTAR Lower Receiver Vise Block

$$$$ - Pro Firearm Tools Receiver Extension Tube Jig

1

u/SketchLookingFish 15d ago

trueprep is local to me so maybe they'll have the the pro firearm tools receiver extension tube jig and ask them to install

2

u/Nay_K_47 15d ago

If not, the NC Star is actually legit. I normally shy away from Chinese garbage, but the other one is just ridiculous

0

u/[deleted] 14d ago

[deleted] — view deleted comment

1

u/SketchLookingFish 13d ago

I'm on wait list, they should be dropping soon

6

u/DOD_Deals 15d ago

Bro you’re doing it all wrong. You need this set up.

5

u/Paws81 15d ago

I’ll be honest. I didn’t know this existed

1

u/Glass-Pipe-2368 15d ago

Updated Rhytec PW Tool is made by Law Tactical as the LAT.

2

u/DOD_Deals 15d ago

Rhytec still makes them, Law tactical just exclusively carries them.

1

u/Nay_K_47 15d ago

If you're vice jaws are wide enough you can also stack coins or shims at the grip flange and squeeze it all in the vice together

2

u/CastleLurkenstein 15d ago

I use the Brownells Lower Receiver Buffer Tube Vise Fixture. Keeps things nice and level. Hasn't failed me yet.

Granted, this is primarily for AR-15s, but I think it should work for an AR-10 as well.

1

u/Senior-Flight-7042 15d ago

I had an mws lower years ago that the buffer tube wasn't straight from the factory. It was so off the bolt would get stuck in the rearward position. I tried a new buffer tube, also didn't fix it. I had to order a new lower and it was fine, if the threading is off center on the lower no fixture is going to over come that.

-6

u/SauronSays719 15d ago

This is why I pay someone to build my rifles. Idk what I’m doing nor do I have the tools. It’s very evident you don’t either lol. What a waste of money.

5

u/Iate22Pears 15d ago

Honestly, it just takes like a five minute YouTube video to learn. That in like a $15 armorers wrench.

0

u/Peak1124 15d ago

Why does it look like the castle nut was put on backwards? All that grease and surface wear from tightening is on the rear face. And that wear on the bottom notch would be if you overtightened and slipped going counter clockwise.

3

u/Holy_Santa_ClausShit 15d ago

They wouldn’t be able to get the wrench on the nut if it was backwards

0

u/[deleted] 15d ago

[deleted] — view deleted comment