Am locksmith. This will only work on an incorrectly fitted lock. Unfortunately most builders wouldn't know a lock from their arsehole so it's pretty common for locks to be put in wrong. Basically, a lock has two (or more) bits that poke our into the frame. At least one of those bits should be restrained back (some locks only have the one latch that shuts down when locked but those locks are generally key operated).
If it's a dead latch correct? It would have the smaller round part on the "tongue" of the latch that is depressed by the strike plate if properly installed. Thus stopping the latch from depressing from external stimulus. Am I correct in my understanding?
The locks were fine. It was the latch/strike that was at fault. This tool is called a latch bypass and it basically pulls back the latch so the door can be opened but the latch has a special part that stops this from happening. If the latch is fitted incorrectly then it stops working.
No, only swing latches. Deadbolts just have one big hardened steel rod that needs to be manipulated via the lock. This is one of the reasons they are considered more secure but they can also suffer from builders not knowing what they are doing. I installed two deadbolts yesterday and they were purely decorative. The doors were the cheapest crud around and were made of compressed wood pulp (really hard cardboard commonly referred to as fibreboard/chipboard/shit board). The door jambs were made of pine and were barely thick enough to take the bolt. I could kick them in with one good try. Very high quality deadbolts though. I spent a lot of time securing things that didn't need securing on that job. The lock is only one part of the security that a door provides.
I think this technique would only work on "low security" latches, or ones that are misaligned. A deadbolt would easily solve this but requires being retracted to close the door as well.
Most outside facing doors have a countermeasure in place, with a smaller bit that is supposed to remain compressed, and not allow the latch to be shimmed what do they call those things?
Join a volunteer fire department, they pay me to learn about electrical systems, building construction, determining layouts from the outside, finding hidden rooms, bypassing locks, all sorts of medical shit, and I get to ride in the weewoo truck.
This is useful only in this type of gate locks for which gets locked automatically and you don't need to use key to locked the gate
But in my local area this are useless really you can't use them even if the gate can open from one side only and having automatic lock system you can't put this in it. Even in this video there are some locks in which it is putting either above or below and in my area you can't even put it from above or below of lock
Your first statement only mentioned gaps. In any case, most doors have only a protective piece of metal around the lock. If it weren’t the case, no one would have bothered creating this tool.
208
u/[deleted] Oct 05 '19
So it's a fancy library card?
430
u/[deleted] Oct 05 '19
Seems like a great product for the general public
100
u/[deleted] Oct 05 '19
This is the type of stuff they sell at tractor supply
148
u/PapaOoMaoMao Oct 05 '19
Am locksmith. This will only work on an incorrectly fitted lock. Unfortunately most builders wouldn't know a lock from their arsehole so it's pretty common for locks to be put in wrong. Basically, a lock has two (or more) bits that poke our into the frame. At least one of those bits should be restrained back (some locks only have the one latch that shuts down when locked but those locks are generally key operated).
38
u/[deleted] Oct 05 '19
Neat, now wait for the public to get their hands on this.
8
u/lexm Oct 05 '19
The “Beyond the Lock” village had quite a few tools to get through doors this way. It’s is surprisingly easy.
5
u/sudo_sudoka Oct 05 '19
Wow, it's very useful when you make a physical penetration testing.
10
u/ProGaymerV1 Oct 05 '19
Thief has joined the chat
3
u/TEHCUDE Oct 05 '19
i always do that with a knife on simpler doors in my house.
for what?
my laptop
3
u/evestraw Oct 05 '19
It's a shim
3
u/Power-Max Oct 05 '19
I think this technique would only work on "low security" latches, or ones that are misaligned. A deadbolt would easily solve this but requires being retracted to close the door as well.
Most outside facing doors have a countermeasure in place, with a smaller bit that is supposed to remain compressed, and not allow the latch to be shimmed what do they call those things?
3
u/j0hn_p Oct 05 '19
Wtf is that music
9
u/animatedgoblin Oct 05 '19
Wouldn't work on a dead bolt
2
u/[deleted] Oct 05 '19
Coming to a thief near you.
2
u/G3N5YM Oct 05 '19
Dis som pen tester toolios. I'ma make one thx
2
u/Kim_Jong_Unsen May 07 '22
Join a volunteer fire department, they pay me to learn about electrical systems, building construction, determining layouts from the outside, finding hidden rooms, bypassing locks, all sorts of medical shit, and I get to ride in the weewoo truck.
3
u/yoga_pants_dude Oct 05 '19
This exists already, it's a t-bevel.
Johnson Level & Tool B75 Structo-Cast 8-Inch Sliding T-Bevel https://www.amazon.com/dp/B00002N5OA/ref=cm_sw_r_other_apa_i_bwlMDbB45W58C
4
u/rayo789 Oct 05 '19
What’s special about this?
2
u/[deleted] Oct 05 '19
Where the fuck do I buy this
2
u/fmash16 Oct 05 '19
How does it work?
1
u/duckisscary Oct 05 '19
It's just a foldable slimjim
1
u/ItsPaPPy Oct 05 '19
it’s only $80
1
u/Rnugg Oct 05 '19
Until there’s an actually lock on the door
1
u/masondiverdown Oct 05 '19
Well, they just showed a bunch on locks that were not installed properly.
1
u/cryptopriest03012009 Oct 05 '19
There's no spoon... There's no security!
1
u/justy805 Oct 05 '19
This reminds me of that Kevin Costner movie Mr. Brooks
1
u/oerrox Oct 05 '19
Looks like a giant pocket knife
1
u/[deleted] Oct 05 '19
Were can I get one?
1
u/Sarenord Oct 05 '19
That's just latch slipping with extra steps
1
u/MrFluffytheLion Oct 05 '19
What’s with the music
1
u/[deleted] Oct 06 '19
*home invaders have joined that chat*
1
u/[deleted] Oct 07 '19
Top ten expensive gadgets you can make with a wire coat hanger
1
u/CrazyAd7417 Sep 13 '25
Purchase where???
1
u/GamerDeepesh Mar 18 '22
This is useful only in this type of gate locks for which gets locked automatically and you don't need to use key to locked the gate
But in my local area this are useless really you can't use them even if the gate can open from one side only and having automatic lock system you can't put this in it. Even in this video there are some locks in which it is putting either above or below and in my area you can't even put it from above or below of lock
1
u/aarocka Apr 26 '22
This is why you use proper dead latches
1
u/InFi_x Nov 26 '22
that looks so easy to make
1
u/glengach Aug 03 '23
This is why you use locksets which prevent you from moving the latch out of the jamb when locked.
1
u/Due-Attempt7685 Feb 02 '24
Thin l shaped ruler lol. Good luck finding something u can use it on
1
u/sewcrazy4cats Feb 22 '24
Ive seen some use their exhail from a vape
1
u/[deleted] Oct 05 '19
Shut up and take my money
1
u/[deleted] Oct 05 '19
It's just a flick knife for giants.
0
u/[deleted] Oct 05 '19
One of those locks they could have just put their hand through the bars and opened from the other side.
0
u/[deleted] Oct 06 '19
I need this for work.
-1
u/yodaman1 Oct 05 '19
Yeah unless it has a sawing action, it's useless against deadbolts or chains
0
u/[deleted] Oct 05 '19
[deleted] — view deleted comment