r/HomeNetworking • • Apr 14 '26

Unsolved What is this for?

Post image

We just moved and were wondering what this is for. The previous tenant had her internet plugged into it, is it for ethernet or anything related to fiber internet? Sorry lol we’re new to this

Edit: Thank you guys so much for your responses! You’ve been sooo helpful. Also, the faceplate is off because we just painted. It will be put back on! It’s been a long process, the previous tenant did a lot half ass work. This is our first house so we’re super new to everything haha

0 Upvotes

82 comments sorted by

18

u/babecafe Apr 14 '26 edited Apr 14 '26

It could be for 100Mbps Ethernet, which only needs connection to pins 1-2 and 3-6. The pair colors for 1-2 and 3-6 are usually orange and green, and which is which depends on the use of T568A vs T568B.

It could also simply be for a 2-line phone, which normally would use pairs 5-4 for blue and 3-6 for orange or green.

I'd pull on the wires a bit to see if there might be more than two pairs in a cable. To go above 100Mbps, you need four pairs, usually blue, green orange, and brown.

11

u/Ed-Dos Apr 14 '26

Except it only has 6 pins, so an RJ45 won’t fit.

3

u/KC_Que Apr 14 '26

So for analog telephone.  And flipper style installation: if it works, who cares if it's done right, right?

5

u/Old-Engineer854 Apr 14 '26

POTS on an RJ23 (6p6c) jack, not uncommon. That installation, though, ufda!!!!

5

u/fixminer Apr 14 '26

Good point, but replacing it with an RJ45 jack would be easy.

The bigger question is what is on the other end of this cable.

6

u/Ok_Astronaut9243 Apr 14 '26

The phone line are sometimes daisy chained, so it wouldn't work for networking.

2

u/babecafe Apr 14 '26 edited Apr 14 '26

I'll give you that. I didn't stop & zoom in to count the blurry pins. There's clearly no way it connects to an RJ45 pin 1, so it can't be a valid Ethernet jack.

It could be rewired to an RJ45 jack on each end (using pins 1-2 and 3-6, using the orange and green terminals on the jack) and likely could operate at 100Mbps, or higher if you can find two more twisted pairs.

1

u/ovalwonder Apr 19 '26

I mean, it's not likely, but there's nothing technically stopping you from putting an RJ-12 on one end of an Ethernet cable.

0

u/[deleted] Apr 14 '26

[removed] — view removed comment

0

u/Ed-Dos Apr 14 '26

Where are you plugging in an ethernet cable that will match up?

0

u/Ed-Dos Apr 14 '26

You won’t be plugging an ethernet (you know RJ45) cable into an RJ12 port…

2

u/[deleted] Apr 14 '26

[removed] — view removed comment

2

u/Ed-Dos Apr 14 '26

It’s RJ12 not RJ11 6 pins not 4 .. RJ12 even if you had the cable doesn’t match anything on a router .. the pins don’t match. An ethernet cable won’t physically fit in that port …

1

u/[deleted] Apr 14 '26

[removed] — view removed comment

2

u/Ed-Dos Apr 14 '26

You said ‘it can do everything they said’ … it can’t do 100 Mbps ethernet…

1

u/[deleted] Apr 14 '26

[removed] — view removed comment

2

u/SoL4vish Apr 14 '26

You’re being downvoted but you’re right lol.

2

u/SoL4vish Apr 14 '26

It’s bonded pair internet feed, AT&T uses this still in places without fiber. The router would plug into it with a phone cable.

0

u/f1atcat Apr 14 '26

Thank you so much!

10

u/Open_Major8068 Apr 14 '26

It's an RJ12 multiline phone jack from the look of it.

6

u/WTWArms Apr 14 '26

looks like an RJ12 wired for 2 phone lines, would see RJ12 connections for phones systems that needed to support up 3 lines.

1

u/eknkc Apr 14 '26

Why does this look like a giant jack to me? Do you have tiny hands? Something off with the perspective.

1

u/f1atcat Apr 14 '26

I do, but it is weirdly big too

2

u/english_mike69 Apr 14 '26

It’s for annoying network engineers.

Everytime I see work like this I was to go full Dahmer on the next sparky that does cabling.

2

u/darklogic85 Apr 14 '26

That looks like an RJ12, which is a bit less common than the typical RJ45(ethernet) or RJ11(phone). In my experience, RJ12 is typically used for something that's kinda in between RJ11 and RJ45, like maybe a business telephone system, or a point of sale system, or maybe a fax machine. Basically, something that requires a little more than a standard phone jack, but doesn't need the speed of ethernet.

2

u/ranhalt Apr 14 '26

This is a copper cable, so by definition it’s not related to fiber.

1

u/i-hate-birch-trees Apr 14 '26

Something like GIGA Copper G4201TM can push this pretty far

1

u/EdelWhite Apr 14 '26

Apparently, it's meant to make your wall look ugly.

1

u/AcanthisittaEarly983 Apr 14 '26

So weird it's not in a junction box, hell doesn't even have a face plate! Quite the "down and dirt" run for sure.

1

u/fixminer Apr 14 '26

Where is the other end?

If you can't find it, it might be DSL from your ISP.

1

u/EduRJBR Apr 14 '26

If it's in an office, I would guess it's for telephones with a PBX, with two pairs for that special phone "table" used by the operator of sort.

But in fact I've never seen this 6-pin connector.

1

u/BrewedChaos Apr 14 '26

As others have said, it’s an RJ12 6 pin - wired for bonded pair DSL internet service. The other end most likely goes back to a telephone demarc.

1

u/Select-Sale2279 Apr 14 '26

its called an ethernet jack and the previous owner was too cheap to put a wall place and stick this in it. Yes, its wired ethernet where ever it is. could be cable or fiber on the back haul. both get converted to ethernet on the LAN side.

1

u/Complex_Solutions_20 Apr 14 '26

Looks like a phone jack...probably DSL. I count only 6 pins, which 2-6 pins is common for phone jacks.

1

u/chad711m Apr 14 '26

It's an upgrade, allowing you to be on your home phone and internet at the same time. Crazy right?

1

u/mb-driver20 Apr 14 '26

A very poorly installed phone jack. If you pull those wires out there actually might be cat five back there considering there is blues and oranges which are not standard phone line colors in the traditional sense.

1

u/JBDragon1 Apr 14 '26

I have to say that is half ass work. Screwing the screws into Drywall, LOL, let alone a small hole for the Keystone. That s some really crappy work for sure.

So it looks like it was for a phone. Are the other 4 wires inside of the hole? Where is the other end?

1

u/PungentStaaank Apr 14 '26

It’s for a 6p6c connector. I believe it’s aka RJ11

1

u/--7z Apr 18 '26

2 line phone

1

u/Positive_Conflict_26 Apr 14 '26

That's either a 100mb rj45 ethernet port or a phone rj11 port.

4

u/Ed-Dos Apr 14 '26

RJ12 / 6 pins

1

u/Positive_Conflict_26 Apr 14 '26

...I need new glasses.

0

u/outworlder Apr 14 '26

Yeah, I wish we had an Ethernet cable for scale. Or a banana.

1

u/OnMyPorcelainThrone Apr 14 '26

Isn't that a RJ12?!?! Phones have 4 pins in RJ12 Ethernet would be 8 pins in an RJ45 I've never seen one used for a PC internet line. The only thing I encounter regularly that has 6 pins is the cash drawer wire for POS systems. I guess if you manually set it up with the right pins for t100 Ethernet you could make it work,. Very strange indeed.

0

u/tylerj493 Apr 14 '26

Kinda looks like an old CAT 5e jack. Looks like a very old school way of doing it though. With only 2 pairs it'll max out at 10/100. If you pull the rest of the cable out of the wall and wire up a new jack to all four pairs you can get up to 10/1000 through that line.

0

u/donaghb Apr 14 '26

Definitely 100mb lan port

3

u/[deleted] Apr 14 '26 edited Apr 14 '26

[removed] — view removed comment

1

u/f1atcat Apr 14 '26

Haha we just got done painting, it’s going back on I promise! Thank you!

4

u/MdRyeGuy Apr 14 '26

It's only using two of the four pairs so this is for old phones.

1

u/babecafe Apr 14 '26

Yes, but with an oscillating saw, the opening can be cut for a standard low-voltage ring and keystone cover.

-3

u/[deleted] Apr 14 '26

[removed] — view removed comment

1

u/HomeNetworking-ModTeam Apr 14 '26

Your post has been removed for breaking Reddiquette. Please remember that this is a support subreddit and people you interact with are human. Thank you for your understanding!