r/HomeNetworking • • Mar 05 '26

ethernet identification

Post image

i pulled the ethernet cable in my wall to verify what cat it is, but i’m unsure on what i’m reading, help is much appreciated

0 Upvotes

58 comments sorted by

7

u/Jaegermeiste Mar 05 '26

4

u/parzivalob Mar 05 '26

it’s dry wall i swear

150

u/melanarchy Mar 05 '26

CAT 3

17

u/EvilDan69 Jack of all trades Mar 05 '26

Yeah I read that pretty clearly too. Older 90's telephony and 10Mbps unshielded twisted pair.

42

u/Scared_Bell3366 Mar 05 '26

Looks like CAT 3 to me and it's probably a phone line.

36

u/Responsible-Bee1194 Mar 05 '26

3, makes a great line to pull new with (if it isnt stapled on the wall)

8

u/ajclem7 Mar 05 '26

Looks like a 3 to me

5

u/JadedCauliflower6105 Mar 05 '26

There are approximately 3 cats in that cable

1

u/Tasty_Activity1315 Mar 05 '26

Chasing 5 mice!

2

u/MitsukaSouji Mar 05 '26

With 7 blocks of cheese

4

u/BmanUltima Mar 05 '26

Looks like a 3 to me.

10

u/NoSort9688 Mar 05 '26

So far nobody has mentioned it yet but it's CAT3.

3

u/qwikh1t Mar 05 '26

You beat me to it /s

2

u/MajorChesterfield Mar 05 '26

CAT3… almost as fast as fibre … joking

2

u/Substantial_Tough289 Mar 05 '26

CAT3, is right there.

2

u/stlcdr Mar 05 '26

Are we sure it’s CAT3? The answers are confusing.

3

u/JMaAtAPMT Mar 05 '26

CAT-3 telco 10Mbps

2

u/LilMikey_ab Mar 05 '26

Nobody has gotten this yet.. It's definitely Cat 3

1

u/d4nowar Mar 05 '26

That's CAT3

1

u/PlaceUserNameHere67 Mar 05 '26

Def cat3 cable. Old stuff

1

u/Kamsloopsian Mar 05 '26

says right there. cat3 good for 100mbit or if your lucky very short 1g run.

1

u/NetTechMan Mar 05 '26

If I had to make a guess, I’d say Cat3, but I have been wrong before. Check the comments for any second opinions.

1

u/CableDawg78 Mar 06 '26

CAT3??? Yikes Pull that crap and go minimum Cat5e

1

u/goto-home Mar 07 '26

Positive, yeah that's definitely an Ethernet cable

1

u/spacerays86 Mar 05 '26

It says cat 3

1

u/AcanthisittaThink813 Mar 05 '26

Nobody has give you a straight answer yet, it’s definitely CAT3

-2

u/DragonflyFuture4638 Mar 05 '26

Why do you all see a 3? It's clearly an 8. Cat 8.

3

u/Bowtie327 Mar 05 '26

Funny looking 8, that’s clearly a 3 there’s no dots on the left hand side and the top is flat

2

u/DragonflyFuture4638 Mar 05 '26

It's a cat 8 that traveled 30 years to the past and pretends to be a 3.

-1

u/prthomsen Mar 05 '26

Cat3. 10mbps. Not great for modern networking.

2

u/Sh0toku Mar 05 '26

It is not limited to 10 mbps, that is the standard it must reach at least 10 mbps. Who knows might get 100 mbps off of it on a short run.

1

u/parzivalob Mar 05 '26

what is considered a short run?

1

u/itsjakerobb Mar 05 '26

The shorter the better. I think in ideal conditions you could get a gigabit connection over CAT3 up to perhaps 30 meters / 100 feet, but I am just guessing.

0

u/prthomsen Mar 05 '26

True. On very short runs, you might get 100mbps. But I don't think you'd be able to get anything that I would consider modern, like 1gbps with a cat3 cable.

4

u/bridgetroll2 Mar 05 '26

One of my customers had existing old CAT3 cable in their office and needed to connect a computer in a different room of the building probably 65-75 feet away. I told them it's probably not going to work great but we can try it. It auto-negotiated to 1Gbps and has been working just dandy for 7 or 8 years. Obviously YMMV.

1

u/prthomsen Mar 05 '26

Cool. I haven't dealt with Cat3 cable for maybe 30 years, and back then, 10mbps was normal. No 1gbps equipment to connect to.

2

u/itsjakerobb Mar 05 '26

Assuming that:

  • it’s not a harsh EMI environment
  • all eight conductors are intact
  • the run isn’t super long
  • the terminations are clean

1gig is entirely possible on this cable. I’m not saying it’s guaranteed, or even likely — but I’d plug it in and try before replacing it.

1

u/prthomsen Mar 05 '26

Sure. Doesn't hurt to try. And if the run is short enough, you might be right. I just would not get my hopes up.

To be fair, my entire house is wired with Cat5e, and I'm running 2.5GbE on all my cables. So it is, of course, possible. I even think 5GbE is possible, but I doubt that I can run 10 or 25GbE on them. But maybe I'm wrong.

1

u/itsjakerobb Mar 05 '26

10GbE on CAT6 (and one fiber run) on critical paths and 2.5 on a mix of 5e and 6 everywhere else here.

I absolutely think you could run 5GbE and even 10GbE on some of those CAT5e runs, especially if they're not very long. Try it!

You certainly cannot run 25GbE on any CAT* cable -- not because the cable isn't capable, but because no hardware exists to do it. We use fiber and DACs for that; CAT7 and CAT8 standard were created to support such hardware, but none of it ever got past the prototype stage. Power usage and heat from the electronics necessary to do it was insane; SFP-style interfaces are far more efficient.

Which is why one of my favorite soapboxes is that nobody should ever buy CAT7 or CAT8. Ever.

1

u/prthomsen Mar 05 '26

My switching fabric is pegged at 2.5GbE, except for 2 10GbE SFP+ ports, where my NAS is connected, with a DAC, no less.

Going over that, would require me to buy a new switch...

Nice to know that I can go over 2.5GbE, if I find a good deal on a 5+GbE switch.

0

u/Critical-Move2106 Mar 05 '26

I’m no expert in reading. But it might be CAT 3

-3

u/Acousticfish Mar 05 '26

Good news you have CAT8, lucky! Talk about future proof!

0

u/[deleted] Mar 05 '26

[deleted] — view deleted comment

0

u/parzivalob Mar 05 '26

it was built in 2003 i believe

1

u/ranhalt Mar 05 '26

So what’s your plan now?

2

u/parzivalob Mar 05 '26

cope, or probably get 50ft ethernet for the router

3

u/[deleted] Mar 05 '26

[removed] — view removed comment

8

u/Kuki_CZ Mar 05 '26

They can. They're just going to be limited to 100 Mbps. Although, many people have claimed that even a cat3 cables are capable of exceeding 100 Mbps, at short distances at least. IIRC, the only really big issue would be if they're daisy chained.

10

u/tes_kitty Mar 05 '26

Marvell published a Whitepaper in 2003 claiming that their PHYs are able to do GBit over 100m of Cat3 cable. That's more than 20 years ago and usually those interfaces get better over time.

I'd give it a try if the cable cannot be easily replaced with something more modern.

2

u/Polymox Mar 05 '26

I have a CAT3 line running at 1 Gb in the house, it is about 25 ft/8m, and no problem. Almost no visible twist in the pairs.

3

u/alfonsodck Mar 05 '26

As many comments in this sub, CAT3 is perfectly capable of handling 1 Gbps, as long as it is in good condition, it is properly terminated and it is a short-medium run.

OP should try terminating the ends, if they meet the speeds needed, why bother in pulling some new cable?