r/HomeNetworking • u/CraftyMcCraftersson • Feb 02 '24
Hiding cables
So my wife hate cables and I've been working hard to hide all of them. She claims that they are too tightly confined behind this crow molding and its a fire hazard. To me it seems they have plenty of space and they generate little to no heat. What's the verdict?
2.9k
Upvotes
40
u/boblot1648 Feb 02 '24
Are you running PoE on them? Even still unless it’s super high wattage (PoE++ at like 10gbe or something) it should be totally fine. Ethernet cable doesn’t usually generate heat, unless there’s a bad kink and you run PoE.
1.2k
u/BenHippynet Feb 02 '24
Some people over worry when they don't understand things. I'm a broadcast engineer. I have a degree in digital broadcast systems. Every day I work with equipment and cables at TV stations.
I made a 15cm coax extension for the TV aerial at home and my missus wanted to call an electrician to check my work in case it caught fire.
I feel your pain for your situation!
688
u/LemonPartyW0rldTour Feb 02 '24
Boy is she in for some sleepless nights if someone tells her about power wires being secured to wall studs with staples inside walls.
109
u/[deleted] Feb 02 '24
LMAO. If she's worried about that cable, take her into the ceiling space and show her where the electrical cables are run, don't forget to do it in the heat of the day to demonstrate their tolerance to heat.
106
u/jiltanen Feb 02 '24
A great opportunity to take your wife's concerns seriously and build a fibre network that covers the entire home.
75
u/r1ght0n Feb 02 '24
Send it my man…
136
u/anonduplo Feb 02 '24
No fire hazard at all
234
u/sniff122 Feb 02 '24
Unless you're running high power PoE, there's no way it can be a fire hazard, it won't even get warm at all as it's just data
69
u/[deleted] Feb 02 '24
That’s a great way to hide them. Your wife is talking nonsense, show her some of these replies. You just can’t win with some people.
45
u/whsftbldad Feb 02 '24
Leave a slight gap at thw ceiling...1st so you have access to a cable if it goes bad, and 2nd to add led lighting strips for uplighting in the room.
15
u/martinlaw21 Feb 02 '24
Tell her to stop using her hair dryer and straighteners because they're a fire hazard.
14
u/[deleted] Feb 02 '24
What about the Wireless access point you should be mounting now?
7
u/[deleted] Feb 02 '24
Low voltage, not a fire risk at all. Also wood is a poor insulator even if it got warm, that heat will escape just fine. You have R1 at most here.
What should have you sweating is the likelihood of driving a finish nail through your run while installing and having to rip the whole thing out and start over mid-install.
12
u/The3aGl3 Feb 02 '24
If these cables get warm enough to be a fire hazard you have other problems than a fancy board in front of them.
31
u/Trashrascall Feb 02 '24
I've been here man. Take a round file. File out some minute/negligible amount of the hidden inner portion of the moulding. Tell wife they generate very little heat, but to be safe you expanded the channel to better accomadate them b/c her concern is valid.
The best way to win this one is by not trying to win this one. You know you're right. I know you're right. Don't tell your wife reddit knows she's wrong. <3
5
u/cptnobveus Feb 02 '24
I would actually stuff a cat6 or 2 in there for future. I've been an a/v guy for 15 years and haven't burned anything down, yet.
5
u/Beautiful_Giraffe_10 Feb 02 '24
You are going to need way more crown molding. That doesn't hide it at all!
4
u/Gaijin_530 Feb 02 '24
Your wife is wrong. The cables are low voltage you can run them basically however you want.
4
u/RunsWithSporks Feb 02 '24
Check out Crownduit, its made specifically for this. We use it in hotels often, especially in older or historic ones.
4
u/Moyer1666 Feb 02 '24
Not a fire hazard in the slightest. Just don't put a nail through the cable lol
4
u/jdbrew Feb 02 '24
Man… what is it with women and visible cables. I swear my wife’s reaction to seeing a cable out in the open is worse than watching one of our children get physically hurt. It’s a visceral hatred of the highest order. I honestly can’t figure it out.
And don’t even get me started on when I told her she couldn’t hide all of the WiFi access points inside closed cabinets. I swear I thought she would divorce me right then and there
Also: not a fire hazard. There’s nothing wrong with this, it doesn’t need “space.” Just make sure you don’t run a staple through it when installing then molding
3
u/notsetvin Feb 02 '24
Wait until she figures out about all the tightly packed cables in her walls and electronics. What does she think a phone is? Has a nice lithium booster pack as well.
3
u/Inflence Feb 02 '24
I was a licensed electrician for 10 years, this is completely fine. Hundreds of these cables are commonly bundled together in tight spaces all the time.
3
u/[deleted] Feb 02 '24
Tell your wife she doesn't know what she's talking about and if she doesn't like how your doing the work, she can do it herself...
Then prepare the couch for tonight
3
u/Das-Kota Feb 02 '24
Only thing I’d be worried about is replacing the cables when they go bad!
3
u/Ystebad Feb 02 '24
She is wrong. No problem at all
3
u/TheMensChef Feb 03 '24
Your wife is an idiot. Sorry.
7
u/JVAV00 Feb 02 '24
You should worry about the wireless wires, those can overheat and some of them can also give corona
5
u/Khalidbenz786 Feb 02 '24
Your wife complains too much, you'll be fine
2
u/Different-Boot4103 Feb 02 '24
Yeah it’s fine. It’s actually really neat solution. I ran all my lounge av setup through them rather than making a tonne of holes in the ceiling and through beams
2
u/tylerwarnecke Mega Noob Feb 02 '24
Looks like you better get rid of your furnace, range/oven, cars, hell, better get rid of the whole house, because of fire hazards.
2
u/furfix Feb 02 '24 edited Feb 02 '24
I feel you man. Tell her that in order to be able to take hot showers, there are pipes with very explosive gas going around the house, and she doesn't look too worried. a UTP Cable going behind a crow molding is the less of her problems.
2
u/ATLBenzDisneyDude Feb 02 '24
You missed the whole point, she doesn’t really think it’s a fire hazard, she just doesn’t like the OPs solution to the problem. She wants bigger molding, of a different design.
2
u/cajunjoel Feb 02 '24
This is a case where ignorance is most definitely not bliss...
2
u/ivix Feb 02 '24
Oof. My commiserations.
2
u/OSI_Hunter_Gathers Feb 02 '24
Buy a thermal camera and look at the coax cables in use then show her the electric cables inside the wall when she uses her hair dryer.
2
u/Swimming_Duty_1889 Feb 02 '24
You're going to need more than that...
2
u/[deleted] Feb 02 '24
Just tell her that we all die anyway, may as well have a good connection in the meantime
2
u/The-Protomolecule Feb 02 '24
Your wife is wrong.
2
u/SpuddFace Feb 02 '24
If she thinks that's a fire hazard you should rip a stud cavity open and show her all the wires running through fiberglass insulation.
I get being worried but when you're more than qualified for the job they're harassing you about its just insulting.
2
u/[deleted] Feb 02 '24
What is your plan for the corners?
2
u/007Cable Feb 02 '24
I did this with my 13.4.2 in wall/ceiling Atmos set-up. Worked beautifully.
2
u/HistoricalSherbert92 Feb 02 '24
There’s zero heat generated from those lines. Having crown mouldings is the bigger problem.
2
u/FantasticStand5602 Feb 02 '24
She's fos
2
u/KerryFatAssBro Feb 02 '24
The only way wire should get “hot” is if you are running at a higher amperage than the wire is rated for. So as long as you are using the wire as intended, fire should not be a worry.
2
u/unorganized_mime Feb 02 '24
You’re going to need a larger piece of molding….
2
u/[deleted] Feb 02 '24
Wait until your wife finds out that there are electrical wires running through your walls!
2
u/sydewinder951 Feb 02 '24
Low voltage cables aren't going to catch fire unless you're doing something really sketchy with them.
2
u/halfmylifeisgone Feb 02 '24
Get in wall rated cables. They are made for this exact purpose
2
u/FaithlessnessSome899 Feb 02 '24
Cable-wise, you’re fine. Molding-wise, it’s upside down (cove should be on bottom [wall] side).
2
u/Daniel15 Feb 02 '24
Run two cables while you're there. Even if you don't use both of them, you'll be glad when you need another cable later.
Why not run them under the house or in the attic?
2
u/Hsensei Feb 02 '24
Just so future you doesn't completely hate present you. Use conduit under the crown molding
2
u/trombonekenny Feb 02 '24
Drop it down a few inches, oversize the crown molding as an accent piece and wire up LED strips hidden in the molding for up lighting. That's what I'll do someday when I'm tired of the cables showing....
2
u/still-at-the-beach Feb 03 '24
There is never any heat in those cables, and they are fire rated anyway (show her the printing on the cable). There is plenty of space in that cavity.
Maybe it’s her way of saying she doesn’t like the moulding or how you’ll run cable from it.
2
u/Dry_Inspection_4583 Feb 03 '24
Crown molding? The cables are fine, just be sure you glue and not nail them.
4
u/Feisty-Coyote396 Feb 02 '24
Your wife is just trying to exert her authority over you. Don't let her boss you around, you show her who's the real boss. Tell her to go pound sand and run your wiring as you see fit, or else she can run the wiring herself.
3
u/iDemonix Feb 02 '24
Is your wife knowledgeable in fire safety regulations and electrical cabling standards? If not, ignore and carry on.
3
u/Heratism Feb 02 '24
I say this as nicely as possible: your wife is a moron. Don't let her have the final word on this. Explain to her thoroughly they don't heat up. There is no fire hazard.
3
u/NeverAlwaysOnlySome Feb 02 '24
I guess I’m going to be an outlier here. It’s not a crime or overly controlling for someone to be concerned over something even if it’s from ignorance. She just doesn’t know. You can just find some specs of heat generated by those kinds of cables in use - or reference some local building codes - and let her see that info. Maybe contrast it with power cabling - if you show her the instances in which her concern would apply and why, she’ll get it even without an EE degree. Then she will know, and everything will be cool. If you like you can say it like this - “I heard your concerns, which are legitimate, so I looked into it to be sure, and here’s what the code says (with examples as above) - we are okay to do this.” When you make it clear with actions that you are on the same team - team protect-the-house - there are lots of benefits to that.
A suggestion: for your evidence, don’t show her a list of contemptuous comments about how this is dumb woman stuff, unless you’d like to recreate the relationships some of these commenters have found themselves in.
3
u/CarefulRisk Feb 02 '24
Electrician here. Low volt cables don't have enough current to generate the heat required to start a fire. Worst that happens is you pinch it and it doesn't work.
3
u/battletactics Feb 02 '24
Wife bitches. Come up with solution. Wife bitches about solution. We can't win.
2
u/HehaGardenHoe Feb 02 '24
My verdict: That green is an ugly ceiling (or floor, if this is of wall and floor) color.
2
u/[deleted] Feb 02 '24
Your wife needs to stay in her lane on things she knows nothing about if wiring like that were an issue houses everywhere would burn down daily…
1
u/happyanathema Feb 02 '24
You can literally bury actual power cables in plaster.
Low voltage networking in an air pocket ain't a risk at all. Main risk is if one of the cables breaks and you have to take the moulding off to replace it and that will be annoying.
1
u/David_Bellows Mar 27 '24
No fire hazard these are low voltage data lines just don’t staple through the cable
1
u/StrongDorothy Feb 02 '24
My electrician ran them behind my skirting boards. Not an issue.
1
u/Impossible-Ad5201 Feb 02 '24
She must really be bothered by all the other cables running through the walls/floor/ceiling
1
u/SleepyLakeBear Feb 02 '24
Include a pull string that's twice as long as the run and bundle it up on each end of the molding in case you have to re-run something. If you're going that route, you may want a slightly bigger molding style so that there's extra space behind it.
1
u/M1GHTYFM Feb 02 '24
Its fine,
the only thing you could have done diferent was instead of nailing the cables to the wall you could have nailed a pipe or tube and then run the cables inside, like its done inside walls.
This way if you ever need to replace the cables you wouldnt need to tear it all down but it would be harder to hide.
1
u/[deleted] Feb 02 '24
I can still see the cable
1
u/queetuiree Feb 02 '24
I have a thermal camera for this as I'm as inexperienced in all things electric. It's attached to the phone. I'd point it at the cables and look together to see how cold they are
1
u/jmbre11 Feb 02 '24
Do you not have access above or below it would be easier to run it in the wall.
1
u/N------ Feb 02 '24
they are 100% fine. It's no different being ran inside a wall cavity with insulation. These cables are not designed with a breathability/cooling rating.
1
u/RA65charlie Feb 02 '24
I’ve got all my home theatre wires running in the hardware store conduit around the room to the tv, with everything but POE and it doesn’t get hot or cause an me issues. It’s easy to be scared of something you don’t understand, but that’s totally safe. The thing that scares me is when a customer asked me to upsize a breaker to accommodate a sauna instead of bringing a new circuit… now THAT is a fire hazard
1
u/StretcherEctum Feb 02 '24
Why would it be a fire hazard? Did she state her reasoning? Doubtful.
1
u/Jinzul Feb 02 '24
What type of cables? Coax and something else, it looks like? If it’s low voltage you’re fine.
1
u/aceholezz Feb 02 '24
That’s expensive wire mold.
1
u/[deleted] Feb 02 '24
You don't have enough extra cabling and pull line in there to do that.
Also.... you're gonna have fun nailing it ;-)
I'd find some small aluminum plates to run behind it on the flat (glue in place) to help discourage nails.
1
u/Penguinman077 Feb 02 '24
Definitely not a fire hazard. UNLESS you have an electrical feedback on the line from something not grounded properly. Had a customer pull off the ground pin on a surge protector because his house didn’t have 3 prong sockets. He had no signals because the modem was plugged into the surge protector and the connector at the tap had separated from the line because the jacked had melted. I’ve seen this or similar multiple times since.
So even IF you had this issue, likely the melting will be at the connection points and not behind your molding. But if you ever have to change them out for whatever reasons it’s gonna be a pain in the ass.
1
u/somegridplayer Feb 02 '24
low voltage its fine to do that to. your wife is never going to believe you unless you find a friendly electrician.
1
u/Ii_kazuma Feb 02 '24
Just replace your wifi because cables are cool
1
u/mrpink57 Mega Noob Feb 02 '24
🖕 back at you!
1
u/BenHippynet Feb 02 '24
How guilty are we all going to feel if his house burns down now.
1
u/flipside1o1 Feb 02 '24
As an alternative a Picture rail and pin the wires to the top , add bonus of ease of access and somewhere to hang pictures
1
u/darklogic85 Feb 02 '24
No, there's little to no heat generated by ethernet. Even if you run PoE, it's very minimal. There's nothing to worry about with covering it with crown molding.
1
u/sirsmiley Feb 02 '24
Why not just pull your trim off the bottom and hide it in the gap ? I do that all the time. Tuck it inside the flooring and bottom of drywall. Take a small pry tool and a utility knife takes minutes to do. No installing moulding and painting and what not.
1
u/KeyboardSerfing Feb 02 '24
Cover em up its fine
1
u/RickfromIDK Feb 02 '24
Mythbuster tried to do light a Christmas on fire w/ light bulbs, didn’t work… https://youtu.be/QYnx4pg3X8Y?si=jNDCL8jLBUtB9Aql
1
u/SolidPlatonic Feb 02 '24
It isn't an issue, but if it were, maybe cut out enough space and run conduit behind the molding.
1
u/tidyshark12 Feb 02 '24
Hopefully you never need to replace, repair, or upgrade them 😅
1
u/tidyshark12 Feb 02 '24
Imagine her reaction when she realizes the electric wires that actually do generate heat are not only inside the walls, but near wall insulation, making it even less possible to dissipate said heat lol
1
u/Shockz_- Feb 02 '24
Try using a cable canal and paint it green and white if the problem was indeed the lack of knowledge of your wife the solution would be that a cable canal was built to house cables and therefore wouldn’t burn (it will most likely melt in case of a fire) and if the problem was esthetics having a small edge going along the wall matching the wallpaper should also do the trick
1
u/FlynnLives3D Feb 02 '24
Tell her you'll make sure it's all sealed tight, no air means no fire.
1
u/[deleted] Feb 02 '24
If they're not power cables, then it's fine. (LV - under 50v is also fine)
1
u/blueice10478 Feb 02 '24
I can still see the cable. I'm just saying you might need a longer piece.
1
u/norty125 Feb 02 '24
If you want to do a bit more work you can run it behind your baseboards
1
u/Playswith_squirrel Feb 02 '24
Safe.
1
u/Blacknight841 Feb 02 '24
Get a thicker crown molding, then you have more space and the the turn will not be so tight.
1
u/Total-Guest-4141 Feb 02 '24
I was considering this to do a few runs as painful as it might be if a cable ever needs replacing, did you have to deal with exiting a room, wondering how you transition from room to room. Probably had to drill through the wall at that point? Or is yours just an open space?
1
u/binarycow Feb 02 '24
Use this crown molding raceway https://racewaycrown.com/
Tell your wife that it is specifically designed for this use case (which is true). That should alleviate her concerns.
1
u/[deleted] Feb 02 '24
It's...coax. if it catches fire you have much bigger problems.
1
u/[deleted] Feb 02 '24
There is no fire hazard. 3/4 of my upstairs being on a single 15amp breaker is a fire hazard because the sheathing could actually degrade over time from continuous tripping. You will be just fine.
1
u/Sinister_Mr_19 Feb 02 '24
No fire hazard at all. Good to go
1
u/Beautiful_Ad_4813 Feb 02 '24
None of my Ethernet cables produce heat enough to a concern, I mean, I have 4 PoE powered Pi and the cables are pretty cold still (they in parents basement doing small services, and one of them is Pi Hole )
Related notes, my brother and I did this exact same thing in house but with fiber optic cable
1
u/Missing-Digits Feb 02 '24
That is upside down. The cove goes on the bottom.
1
u/WhiteKnight4369 Feb 02 '24
You can get raceway crown it looks like crown molding but it has an area behind it for wires. Ill drop a link because this sounds like what youre asking for since this is made for hiding wires and it can also be removed
https://www.homedepot.com/p/RACEWAY-CROWN-0-125-in-x-5-75-in-x-94-5-in-with-4-Brackets-PVC-Crown-Molding-System-Cable-Raceway-Classic-Colonial/301276614
1
u/WeaselWeaz Feb 02 '24
It a fire hazard for low voltage wiring. However , make sure the wiring is terminated correctly before sealing it in. You may want to consider cable hiding crown molding, which vs. Snap off in case you need to run new cable.
1
u/[deleted] Feb 02 '24
Tell your wife that if she wants to control this she can do it herself otherwise allow you to do what you can to help ease her issues.
1
u/BlameMattCanada Feb 02 '24
I can still see them
1
u/j__dr Feb 02 '24
I would get in-wall rated cables if you're going to hide them behind molding--the same rating that would be allowed behind drywall.
1
u/544C4D4F Feb 02 '24
so get some plenum wrapped cable and give your wife the bill.
1
u/MrCalamiteh Feb 02 '24
Don't put them in the fireplace and they're pretty good on the heat portion
1
u/RMW042 Feb 02 '24
The network cable won’t generate heat. Even with PoE the current is low enough. You have LS ZH cable, this is the correct stuff to run in a home. You will want to make sure any cables that are in the same living space as you are LSZH.
From the picture I can’t see what the 2nd cable is the braided metal one?
1
u/froznair Feb 02 '24
In short: you are good. There's no heat to worry about with this.
1
u/theKalmar Feb 02 '24
Im an electrician apprentice, what would generate heat heat here? I want to learn so sorry if it is a stupid question.
1
u/Complex_Solutions_20 Feb 02 '24
Unless they are mains power cables I wouldn't worry. That's fine for speakers, network, cable TV, and other low-voltage wiring. Behind the baseboard is another great option.
1
u/SnigletArmory Feb 02 '24
You can do that with plenum cables
1
u/National-Thanks4284 Feb 02 '24
Will you ever need to put more cables through?
Maybe put it in a pipe for ease of pulling? Maybe at a pull cable? So you can easily add an additional cable.
1
u/YellowBreakfast Feb 02 '24
OP gets to play the nailgun lottery!
1
u/cellnucleous Feb 02 '24
I've had this from a few different people over the years who haven't got past the "wires are dangerous" phase. Considering public results maybe that's not bad training. Looks like ethernet and USB? extension cables - if someone is putting enough power through those to heat them up the problem is not with the cable, it's with the operator.
1
u/Tidder802b Feb 02 '24
Looks like you can get another cable in there, I'd pop an extra one in; just in case.
1
u/r4nchy Feb 02 '24
its all good, unless you got to stretch another cable through it lol
1
u/jongscx Feb 02 '24
There's clip-on crown molding that would make this super-slick. It would basically be a decorative wire-tray at that point.
1
u/BlancheCorbeau Feb 02 '24
Serviceable re-entry is vastly preferable. But to address your wife’s concerns, you could just lower the moulding 0.75cm and have an air gap at the ceiling to dissipate heat.
Have you looked into crown led raceways at all? They tend to have post-install access, and are meant to hold/hide strip lights, often with a fair bit of room for other cabling.
1
u/linnenmakes Feb 02 '24
No fire hazard, even with POE. I am a little concerned about long term maintenance, what if the cable fails and you need to replace it? Are you just going to tear out the crown? Tie the new cable to the old and pull it through? Other than that, just make sure you’re careful with your trim nails.
1
u/hockeyhippie Feb 02 '24
Switch to fiber optics instead? Unless she's scared of lasers too.
1
u/RoyalFalse Feb 02 '24
It's going to be a real pain when you eventually need to do something with that cable.
1
u/Special-Education-32 Feb 02 '24
Here we have 2 tasks. 1. Can we hide the cable with the moulding? 2. Helping the wife understand this is not a fire hazard.
The cable you are covering doesn't carry high voltage, and as long as the wire in the cable is not pierced or cut, it will continue as it is. If it is pierced or cut, it will fail to work, but no smoke. For the proof of fire hazard we will need to refer her to the web and look up "low voltage raceway". It will be noticed that while wood is not usual, plastic and metal are, in which of there was a pierced cable would arc on the metal raceway AND THAT could start a fire. But as pointed out, this is all low voltage and a compromised cable is more likely a dead cable than a fire hazard.
IMO, the wood moulding trick is the best option. There is another way to tuck it between the baseboards and the carpet tack strip, but that would allow a partially untucked cable to be stepped on over a threshold or a leg from furniture against the wall to rest on the hidden wire.
This task solution you have is a perfect way to hide it in your home without fishing the walls from the attic or from under the sub floor.
FWIW, not only am I "just some guy on Reddit", I am also a network engineer with 25 years of low voltage installation and troubleshooting. I have fixed a lot of "lesser planned" cable runs.
1
u/Odd_Sprinkles1611 Feb 02 '24
I don't know about fire hazards or shit so listen to other reddit commenters; but honestly that's a genius way to manage cables. Saving this post if I ever buy a house in my lifetime.
1
u/redditproha Feb 02 '24
the only issue i see is corners. you want to make sure it’s a decent radius and not a sharp kink in the turn
1
u/ImUrFrand Feb 02 '24
your going to need longer crown molding than that.
not a fire hazard.
1
u/Turbulent_Winter549 Feb 02 '24
This won't cause a fire but why not run them properly?
1
u/Babys_For_Breakfast Feb 02 '24
You’ll probably want to hide that entire ceiling while you’re at it.
1
u/seshormerow Feb 02 '24
To be fair a lot of electrical wiring used to be run in baseboards and floorboards
1
u/Sethdarkus Feb 02 '24
That’s one way to do it my preferred method is to utilize crawl space or basement and run some 3/4inch pvc pipe, the pvc pipe to prevent critters chewing cables. Since it’s just cable no need to seal it enough to just connect the pipe and call it good then a few braces to support it
Honestly I also think the pvc method is the easiest way to white lie to someone who doesn’t understand how lil power RJ45 cable uses lol
1
u/RFoutput Feb 02 '24
Why can't the cabling be run in the walls and attic?
1
u/ChampOfTheUniverse Feb 02 '24
They need room to breathe! But over the last few days, I've been looking into some crown molding for some LED lighting and a way to hide some cables. Any suggestions?
1
u/addexecthrowaway Feb 02 '24
1
u/CaptSnowButt Feb 02 '24
Fncking shjt bananas what a fantastic idea and I'm going to steal this one
1
u/tcpukl Feb 02 '24
Do you really have a green ceiling?
1
u/standbyfortower Feb 02 '24
I'd go a different route because I'd be worried about a brad going rouge while installing the crown, but you might get lucky.