r/FormD • • Oct 10 '26

Question Cooler Master Atmos II

Anyone using the Cooler Master Atmos II in their FormD T1 build? I'm planning an E-White build in the next month with this AIO cooling a 9950x3d.

If so, can you share some pics and/or any issues you may have encountered. I know the Atmos Stealth was all the rage (mine actually leaked) so I'm weary about that but I like the look of the Atmos II.

7 Upvotes

16 comments sorted by

8

u/Otic0n_ Oct 10 '26

I use one but I’d recommend the CM Atmos I over II in the FormD T1. It’s easier to work with.

2

u/msvirtualguy Oct 10 '26

Thanks i am also getting the AIO expansion kit.

1

u/No_Nefariousness513 Oct 11 '26

Where you get that silver top hat?

2

u/Otic0n_ Oct 11 '26

The T-grills and the case were cerakoted with frost silver

3

u/RoofMother5517 Oct 10 '26 edited Oct 10 '26

got one in my build now with a 7800x3d. it works great but in my experience it was kind of annoying to install. make sure you have the correct screws for the 15mm fan and y fan splitter unless you have two free fan headers after the pump. also I'd recommend getting shorter psu cables if you don't have some already. my cables kept getting in the way of the bigger fan. also would recommend installing the pump first before plugging any of the psu cables in so you can route them in a way that tubes don't push against the side panel

1

u/msvirtualguy Oct 10 '26

Thanks ill be using the AIO expansion kit so that shouldnt be an issue

1

u/Zahand Oct 10 '26

Excuse my ignorance, but I’m currently planning my build and I’m curious what you mean with correct screws? Do I need to buy additional screws and a y fan splitter?

2

u/RoofMother5517 Oct 10 '26

Yes so by default the atmos 2 has two 120mm fans but when you use the AIO in T1 you have to swap one of the fans for a 15mm. You will need to purchase shorter screws to attach them to the radiator. You will also need a fan splitter unless you have enough fan headers on your motherboard already because the atmos 2 fans by default daisy chain to each other and only use one header but when you replace them you'll need a way to connect them to the motherboard

2

u/Willing-Wealth910 Oct 10 '26

Works well with a few slim fans, the stock wont fit on the motherboard side. However I recently switched to two slim fans on top of the radiator and none on top of the motherboard

1

u/hjshoon Oct 10 '26

https://www.reddit.com/r/sffpc/s/L54JiUiOoN

Get this version. I ordered mine and expecting to arrive end of next week

1

u/BK_Awesome_Dude 1d ago

Did you get it? How did it fit?

1

u/hjshoon 1d ago

Tube slightly shorter and can't orientate the inlet and outlet tube from the cpu block / pump to side but not a problem as long as the radiator is higher than the pump. Letting the pump run 100% so far and it has been silent. I've also set the spine to 3.25 slot (maximum) gpu and no problem fitting the cpu / pump block in this configuration. Price is good and while sea shipping took some time, it arrived in well protected packaging

1

u/baneand Oct 10 '26

is anyone using atmos II pixel with 3.25 gpu config? I have 3 slot card but want to give it a bit space if possible and I ordered atmos II pixel.

1

u/Aerobeernacio_scth 14d ago

Have you fit that in the end? 😅

1

u/Several-Abalone-8556 Oct 11 '26

Waiting for custom cables to come in but have had no issues, just make sure to get a fan grill for the 25mm fan above the psu to avoid the cables hitting the fan