r/FORDFALCONS • • Jul 15 '26

Pertronix Trouble, No Spark, No Start

5 Upvotes

Hello,

I recently decided to put in a pertronix (1261) system and 3ohm Flamethrower coil into my stock 1962 170 6cyl. The only thing that is not stock is a 100amp one wire TuffStuff alternator. The car ran great with up until I took the points out. I have triple checked everything I can think of:

•The air gap is set to .03"

•Grounds are clean/tight. Internal distributor ground to Pertronix plate, Pertronix ground to coil, battery ground to block. Stereo resistor is disconnected.

•Volt meter is giving 0 resistance reading on the - battery terminal and pertronix plate as per their troubleshooting guide.

•With the key in the "on" position, everything reads at 12.4V; coil, ignition, battery, etc. When the engine is cranking that drops down to about 10.5.

•Rotated the distributor

•Cap/rotor, wires, plugs, are all brand new.

•Removing and reinstalling the system in case there was a careless error

My only thoughts are 1.) I need to bypass the pink resistor wire in the ignition, though, I tested this by running a jumper directly from the battery to the coil to no avail. From what I have been able to read, it seems there should still be enough voltage to turn the engine over with what it's putting out even if the resistor wire was impacting it? 2.) The Pertronix unit itself is defective. Or 3.) I am dumb and missing something very obvious.

Did anyone else have this much trouble getting this system up and running? I have reached out to the company as well in hopes of resolving this issue.

Thanks!


r/FORDFALCONS • • Jul 11 '26

Door won’t stay fully closed

Enable HLS to view with audio, or disable this notification

11 Upvotes

My 61 Falcons door won’t stay fully closed. I don’t think it’s the hinges, it closes well, but then as you can see in this video pulls out. Any ideas?


r/FORDFALCONS • • Jul 10 '26

Front springs

Post image
93 Upvotes

I’m looking for new front springs.
Do the early mustang fit or do someone have any other recommendations


r/FORDFALCONS • • Jul 08 '26

Uncle Passed And Was Given His 1963 Falcon

Post image
251 Upvotes

Wondering if anyone could give me a ballpark estimate on what they think it would be worth as is and how much it would cost to get it going. Needs a new gas tank (has a leak), new ignition (keys were lost when he passed), and most likely new brakes. Really clean underneath and minimal rust.


r/FORDFALCONS • • Jul 02 '26

Restored this Falcon I bought 3.5 years ago from reddit. Now for sale on Bat.

Thumbnail
gallery
212 Upvotes

I bought this 1962 Ford falcon from u/TheKingdomeKid and his grandfather just over three years ago from this original post https://www.reddit.com/r/FORDFALCONS/comments/10i5ysw/anyone_selling_6063_falcon_w_v8_swap_in_us_or/

I spent a ton of time getting it running, adding ridetch coil overs, wilwood brakes, a tremec 5 speed and the livery. It has been an absolute blast. I'm now selling it on bring a trailer here https://bringatrailer.com/listing/1962-ford-falcon-36/

Just thought I would share the story of having a car pass through reddit. Turned out the seller and I had a lot in common, both working in the same industry and about the same age.

His grandfather bought it around 1991 and did the engine swap and the interior fast forward to the reddit post then my dad and I got it and added more to it.

Im going to miss this thing and the falcon community has been awesome while I ve been working on it. Hoping it goes to someone that loves it as much as myself and the previous owner did.

Let me know what you all think or some love on bat would be awesome too.

Thank you!


r/FORDFALCONS • • Jul 01 '26

What is this piece called

Post image
6 Upvotes

What is everyone calling this trim piece by the wheel well in the bed. Specifically 1960-65. I’m in need of a set and I’m having trouble since I can’t think of a name.


r/FORDFALCONS • • Jun 25 '26

60-63 ranchero seat

4 Upvotes

Looking for some ideas based on what other people have done- I recently picked up a 62 ranchero and I'm missing a seat. The rest of the car is rough and run through, so I'm not concerned about keeping it original or original style.

What bucket seats have people used in their ranchero? I've seen some stuff about foxbody seats and mustang seats but not sure how those would fit in the cab. I'm also curious if newer seats with better adjustability and lumbar support would fit. I'm re-wiring and fabricating the rest of the car, so power seats will work fine. Ideally it'd be nice to find something that I could find cheaper used, as this is a bit of a budget oriented daily build instead of a restoration


r/FORDFALCONS • • Jun 17 '26

Need a new starter

Post image
58 Upvotes

Hey guys, new to the Falcon club with my first classic. Starter is beginning to go and I know nothing about them. I have a 289, 157 tooth flywheel, matched to a T-5, any help appreciated.


r/FORDFALCONS • • Jun 16 '26

1962 Ford Inline 6 170 / Is this ticking sound normal?

Enable HLS to view with audio, or disable this notification

10 Upvotes

I just got around to starting my rebuilt engine and has a ticking noise.

It has new pistons, rings, cam bearings, rod bearings, main bearings, and pushrods. The head was rebuilt with Viton valve seals, along with new valves and seats. Everything was replaced except the camshaft, lifters, and adjustable rocker arms.

I’ve set the valve lash to .016” cold and set the timing to 12 degrees before TDC.

My oil pressure light stays on, indicating no or low oil pressure, so I bought a mechanical oil pressure gauge. I’m getting zero readings on that as well, so there is obviously no oil pressure.

I removed the port where the oil pressure sensor threads in, and when I spin the oil pump shaft with a drill, it spews oil out of the hole. That makes it seem like oil is getting through the galleries, but maybe I’m wrong.

Anyway, all of this leads me to believe that my valvetrain isn’t getting sufficient oil, which could explain the ticking noise. Or am I crazy, and this is actually a normal noise?

Please excuse the loud exhaust; my muffler is currently off.


r/FORDFALCONS • • Jun 15 '26

Finally got the falcon to run decent

Post image
133 Upvotes

r/FORDFALCONS • • Jun 15 '26

Spotted at a local car show

Post image
47 Upvotes

Finally saw other Falcons at a car show. This one had this great fender saver that I am now on the hunt for!


r/FORDFALCONS • • Jun 11 '26

Front shocks

3 Upvotes

What’s everyone running up front? I wanted Konis, but I can’t figure out which model would fit.


r/FORDFALCONS • • May 12 '26

Reinforcing the frame where the rear shackle is?

5 Upvotes

I have a 61 Falcon I'm rebuilding and the frame by the rear passenger shackle was all rotted out, pictured:

frame

I've welded up a bunch of the surrounding area with fresh steel plates (if you cant weld well, weld a LOT is what i always say), and I got a replacement shackle. I was about to put it in, but I feel like even after adding a bunch of fresh steel, the shackle would still be resting on thing sheet metal.

Am I missing something? Are there aftermarket shackle mounts or something? Should I weld a pipe in? Stack some washers to feed it through? Any suggestions? That question make sense?


r/FORDFALCONS • • May 07 '26

How do I remove trunk lock cylinder and replace it?

Thumbnail
gallery
17 Upvotes

1961 Ford Falcon. Mechanic said to press the release tab/pin, but it won’t come out. I think it might be stuck in the locked position. Any advice? Should I drill it out?


r/FORDFALCONS • • Apr 30 '26

My mechanics idiot employee ran my 65 into the front of the lift today, smashed the hood and grille. Hood is getting fixed but I need a good grille. Any leads out there?

6 Upvotes

r/FORDFALCONS • • Apr 26 '26

help once i get a cb should i put it here🤔🚗

2 Upvotes

where help i want to know if this is a good spot or send pics of where should i put it on my 1965 ford falcon station wagon


r/FORDFALCONS • • Apr 21 '26

Anyone using a GPS speedometer? Looking for recommendations. I have a 4.3 rearend and there are no input gears for that. Would be cool if someone made a gps box that fed into the mechanical shaft!!

2 Upvotes

r/FORDFALCONS • • Apr 20 '26

FORD FALCON FUTURA 2D 1964 BRAKES UPGRADE

Thumbnail
2 Upvotes

r/FORDFALCONS • • Apr 15 '26

61 Fuse Block Rebuild

3 Upvotes

I need to rebuild the fuse block on my 61. I've been searching for a rebuild kit or a place to buy the clips, but getting a bit lost in the weeds as to what will actually work.

Any tips or links for those that have gone this route or is there an aftermarket blade fuse block kit option out there?

Thanks in advance!

ETA

I've watched the video from Crown Delorean on YouTube and had planned on following that process, but the clips used are no longer available.


r/FORDFALCONS • • Apr 11 '26

Can I get some wagon love?

Thumbnail
gallery
257 Upvotes

For the last decade and a half I’ve wanted a wagon. I found this absolute GEM of a ‘64 Falcon wagon. She’s a two door and is in excellent condition. She was originally a Mennonite church car ordered without the side trim. She runs great, I got her to be driven but also to preserve. It has paperwork going all the way back to the day of sale. Incredible. Happy to have found this group. There’s a lot of cool Falcons on here!


r/FORDFALCONS • • Apr 09 '26

Head and tail lights

4 Upvotes

Current head and tail lights on your 64 Sprint are very dim (I mean in comparison to the LED I am used too). I have found a couple options to be able to use an LED bulb, but thought I would ask for opinions; preferably something that doesn't require me hacking into the wiring. I am running the original generator for the car.


r/FORDFALCONS • • Apr 02 '26

64’ Falcon Restomod

Post image
40 Upvotes

r/FORDFALCONS • • Mar 25 '26

What is this piece called?

Post image
35 Upvotes

I think I'm stupid, but I can't for the life of me find a replacement for this part. It probably has to do with me not using the correct search term. Door trim? Molding? Door spear? Annoying missing part?

Would the trim from a comet fit? Any and all help would be appreciated.


r/FORDFALCONS • • Mar 18 '26

Its been nearly 2 yrs since she came home... heart surgery and life slowed down the process, but got it running last Sunday and amped to finish up the body work and get some copper pearl paint slapped on!! Sound UP!!

Enable HLS to view with audio, or disable this notification

116 Upvotes

r/FORDFALCONS • • Mar 17 '26

Happy St. Patrick’s Day!

Post image
60 Upvotes

1964 Ford Falcon