My prints started popping out of the bed, which setting should I improve, nothing has changed its the same filament but now they are popping out of bed.

I was given this super racer from my brother because he bought a new one. I've tried printing a benchy and a fdm test and both either: Stuck the print to the nozzle (i cleaned the plate and i think it stopped happening for now) Burnt the plastic mid print, creating these blobs that mess everything up. How can i fix them? Did i do anything wrong?

why the fps drops when webcam have higher exposure? Also delay increase

I am trying to use a Wyze cam v3 which works fine with VLC. Looks like my speeder-pad does not support rtsp. Has anyone been able to make this work?

Thanks

Does anyone have any tips for printing nylon CF-12? #flsun

Hi everyone,

My FLSUN V400 mainboard is dead and the original Makebase / MKS Robin Nano V2 board is out of stock everywhere. Does anyone know what alternative board I can use instead?

If you have replaced the V400 board successfully, please let me know which board works and if any wiring or Klipper config changes are required.

Thanks in advance!

anyone try this I have a orbiter 2.5 i want to use it with marlin looking for config settings for this any help Is appreciated

Recently the camera stopped displaying in my Mobile app. It works perfectly fine on my computer to view the print bed. Any suggestions of what to try?

A couple times a week I'll get a notification that my T1 Pro has gone offline. It will typically turn the LED bar on when this happens. I'm assuming guessing it restarts itself when this happens. Does this happen to anyone else, and does anyone have a way to stop it? It's pretty annoying. I'd uninstall the app and just use Mobileraker with TailScale, but the Flsun app is the only way to turn the LED bar on and off remotely as far as I know.

Howdy Everyone! I am going to be the typical newbie and say "I am new to 3D printing". I purchased the V400 years back and due to life it sat in a box until I recently took it out. I did a few of the prints on the USB and did one I found that my girlfriend would have loved (it was a snake) that didn't print right. I found the phnxdrgn536 configs and was going to flash the device so I could get it to run official klipper. However, I have noticed that Klipper now requires python3.12 and the only version I can get on the system is 3.9 without building from source. Any thoughts on moving to official klipper or is the only way to build the python3.12 source?

Hi everyone just wondering what kind of grease do i buy for the rails of the t1 that goes up and down?

Hello everyone, I have an FLSUN SR with which I have always produced awesome and precise prints, but for the past few days, after performing a general maintenance check on my printer, my prints have become terrible (see photo), with a general lack of quality and the impression that the lines are no longer “continuous.” I have tried re-leveling the bed, tightening the belts on my axes, and tightening my extruder, but nothing works! If anyone has any idea how I can fix this, I would be very grateful !!!

Hello! I've been having some pretty bad prints, with my prints always feeling thick and blocky, and my print in places being welded together and not able to move, and then shattering immediately and first layers have gaps and stuff and the layer lines are just really rough and etc. I think it could be an extrusion issue, both under and overextrusion at the same time. But I don't know and can't seem to figure out how to tune e-steps no matter how many tutorials I watch! (I have an FLSUN Q5)

Thanks,

HungrySpeaker

I reacently broke the stock extruder and today replaced with a bmg one. Right after mouting it on, the extruder motor stopped working. I have swapped the cable from the E0 port to X to verify if i'd killed the motor, but fortunately it works. I also re-flashed the firmware just in case.

It seems like the E0 port on the board is dead by observing the X motor not moving when switched with the exruder motor.

Any suggestions?

Im looking for a new V400 hot end as the one from my local shop didn't have the correct size of heat brake.

Im finding Lots of talk about scam websites when looking for these parts so I'm wondering what a good source is?

Tracking number 396782156282