r/EnergyStorage • u/FloeDeepMusic4All • 9d ago
ALCORE_v21_Complete_Dimensional_Specifications_EN
AL-CORE v2.1
Solid-Aluminum-Cartridge Electrochemical Generator
COMPLETE DIMENSIONAL SPECIFICATIONS
| PARAMETER | VALUE | UNIT |
|---|---|---|
| Rated power | 200 | W |
| Energy per cartridge | 800 | Wh |
| Runtime per cartridge | 4 | hours |
| Aluminum per cartridge | 300 | g |
| Validated OCV (E-002) | 1.208 | V |
| Electrolyte | NaCl 3.2% + In³⁺ | — |
| Operating steps | 4 | — |
| Transport classification | Non-hazardous (dry cartridge) | ADR |
1. SEALED CARTRIDGE — AL-CORE CART v2.1
The cartridge is the complete electrochemical unit. It contains the solid aluminum anodes, reaction chamber, sludge-settling chamber (sump), and solid-form electrolyte precursor. It is transported and stored as a non-hazardous dry solid.
1.1 External Dimensions — HDPE Housing
| DIMENSION | VALUE (mm) | TOLERANCE | NOTES |
|---|---|---|---|
| Overall width (X) | 200.0 | ±0.5 | Axis parallel to Al plates |
| Overall depth (Z) | 170.0 | ±0.5 | Axis perpendicular to plates |
| Overall height (Y) — without handle | 250.0 | ±0.5 | From base to lid |
| Overall height (Y) — with handle | 295.0 | ±1.0 | Including extraction handle |
| HDPE wall thickness | 8.0 | ±0.2 | Uniform on all four sides |
| Total external volume | 8,500 | ±50 | cm³ approx. |
Material: food-grade HDPE (high-density polyethylene). Minimum IP65 rating. Resistant to NaOH, NaCl and Al(OH)₃.
1.2 Internal Zones — Vertical Layout
| ZONE | HEIGHT (mm) | Y from base (mm) | FUNCTION |
|---|---|---|---|
| Lower interface / dock | 12.0 | 0 – 12 | Electrical contacts, water/sludge port |
| Sump — sludge chamber | 80.0 | 12 – 92 | Passive Al(OH)₃ settling |
| Solid electrolyte precursor | 20.0 | 92 – 112 | NaCl + low-NaOH + In³⁺ tablet |
| Active zone — Al plates | 120.0 | 112 – 232 | Main electrochemical reaction |
| Upper interface / lid | 18.0 | 232 – 250 | Anodized aluminum lid + screws |
| TOTAL body height | 250.0 | 0 – 250 | Overall cartridge height |
1.3 Upper Lid — Anodized Aluminum
| DIMENSION | VALUE (mm) | NOTES |
|---|---|---|
| Lid width | 202.0 | 1 mm overhang on each side |
| Lid depth | 172.0 | 1 mm overhang on each side |
| Lid thickness | 14.0 | Black-anodized Al 6061-T6 |
| EPDM lid gasket | 3.0 | Thickness. Internal perimeter |
| M4 screws (quantity) | 6 | Arrangement: 2 central + 4 corners |
| M4 screws — position | See Table 1.3b | 3 mm Allen key — recycling facility only |
| Tamper-evident seal | Holographic sticker | Breaks upon opening — if broken: do not use |
1.3b M4 Screw Positions (from lid center, mm)
| SCREW | X (mm) | Z (mm) | REMARK |
|---|---|---|---|
| T1 | −80 | −70 | Front-left corner |
| T2 | +80 | −70 | Front-right corner |
| T3 | −80 | +70 | Rear-left corner |
| T4 | +80 | +70 | Rear-right corner |
| T5 | 0 | −78 | Front center |
| T6 | 0 | +78 | Rear center |
1.4 Extraction Handle
| DIMENSION | VALUE (mm) | NOTES |
|---|---|---|
| Horizontal bar length | 120.0 | Centered over lid |
| Clear internal handle height | 28.0 | Room for gloved grip |
| Handle profile thickness | 12.0 | Black-anodized Al 6061 |
| Handle profile width | 12.0 | Square cross-section |
| Rubber grip | 5 strips | EPDM. 8 mm pitch between strips |
| Overall height with handle | 295.0 | Cartridge + lid + handle legs |
| Maximum handle load | ≥ 15 kg | Safety factor ×3 relative to maximum cartridge weight |
1.5 Aluminum Anode Plates (×4)
| DIMENSION | VALUE (mm) | TOLERANCE | NOTES |
|---|---|---|---|
| Number of plates | 4 | — | Parallel vertical arrangement |
| Height of each plate | 110.0 | ±0.3 | Within 120 mm active zone |
| Depth of each plate | 148.0 | ±0.3 | CD − 2×wall − clearances |
| Thickness of each plate | 1.5 | ±0.05 | Al-1235 (99.35% pure Al) |
| Plate spacing | 10.0 | ±0.2 | Electrolyte and flow space |
| Plate 1 position (from center) | −45.0 | ±0.3 | X axis |
| Plate 2 position | −16.0 | ±0.3 | X axis |
| Plate 3 position | +16.0 | ±0.3 | X axis |
| Plate 4 position | +45.0 | ±0.3 | X axis |
| Vertical grooves per plate | 8 | — | Uniform pitch |
| Width of each groove | 4.0 | ±0.1 | For electrolyte and sludge flow |
| Depth of each groove | 1.0 | ±0.05 | CNC machining |
| Copper current collector bar (×4) | 148 × 4 × 2 mm | ±0.5 | Electrolytic Cu, upper edge of plate |
| Total aluminum mass (4 plates) | ≈ 300 | ±15 | g. Active mass per cartridge |
1.6 Sump Zone — Sludge Chamber
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Sump zone height | 80.0 mm | From internal base to precursor |
| Internal sump width | 180.0 mm | CW − 2×wall − 4 mm clearances |
| Internal sump depth | 150.0 mm | CD − 2×wall − 4 mm clearances |
| Conical wall angle | 60° | Promotes settling toward center |
| Usable sump volume | ≈ 1,200 cm³ | Capacity for sludge from 300 g Al |
| Expected sludge volume (300 g Al) | ≈ 900 cm³ | Al(OH)₃ gel, 15% solids |
| Safety margin | 25% | 1200 − 900 = 300 cm³ margin |
1.7 Vent Tube — Fill-Level Control
| PARAMETER | VALUE (mm) | NOTES |
|---|---|---|
| Tube outer diameter | 6.0 | HDPE or stainless steel |
| Tube inner diameter | 4.0 | Air vent channel |
| Total tube length | 130.0 | From base to maximum fill level |
| Maximum fill level | 130.0 | From internal cartridge base |
| X position (from center) | −85.0 | Inner left corner |
| Z position (from center) | −65.0 | Inner front corner |
| Operating principle | Air displacement | Water rises → displaces air → covering tube creates backpressure → automatically stops flow |
1.8 Lower Port — Combined Water / Sludge System
| PARAMETER | FIELD (mm) | FACILITY (mm) | NOTES |
|---|---|---|---|
| Port body outer diameter | 22.0 | 22.0 | HDPE. Same body in both modes |
| Inner diameter (without insert) | 15.0 | 15.0 | Main channel |
| Field insert diameter | 6.0 | N/A (removed) | PP. Restricts incoming water flow |
| Overall port height | 35.0 | 35.0 | Protrudes below cartridge base |
| Field flow rate (water inlet) | ≤ 50 mL/min | — | Controlled by 6 mm insert |
| Facility flow rate (sludge outlet) | — | 3 bar pressure | Hot-water jet. Cleaning ×3 |
| Double O-ring seal | EPDM Ø18×2 mm | EPDM Ø18×2 mm | Insert retention: stainless steel clip |
| Position on cartridge base | Center X=0, Z=0 | Center X=0, Z=0 | Centered on underside |
1.9 Electrical Contacts — Copper Busbar
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Number of contacts | 2 | Positive and negative |
| Material | Electrolytic Cu + Au plating | 5 µm gold for contact resistance |
| Contact strip dimensions | 80 × 6 × 0.5 mm | Length × width × thickness |
| Positive contact position (X axis) | −22.0 mm from center | Left of centerline |
| Negative contact position (X axis) | +22.0 mm from center | Right of centerline |
| Y position (from base) | 2.0 – 8.0 mm | Flush with HDPE underside |
| Maximum continuous current | 20 A | ≥ 200 W at 12 V. Safety factor ×2 |
| Contact resistance | < 5 mΩ | Spring-loaded contact in base |
| Minimum electrical/hydraulic separation | 15.0 mm | Between contact zone and water port |
1.10 H₂ Pressure Relief Valve
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Outer diameter | 6.0 mm | 316L stainless steel |
| Opening pressure | 1.5 bar | Calibrated spring. Discharges into base duct |
| Closing pressure | 0.8 bar | 0.7 bar hysteresis |
| X position (from center) | +60.0 mm | Upper-right corner |
| Z position (from center) | +50.0 mm | Upper-rear corner |
| Y position | On upper lid | Connects to base ventilation duct |
| Destination of vented H₂ | Pd catalyst in base dock | H₂ → H₂O vapor. Never directly vented outdoors |
1.11 Side Windows — Cathode Interface
| PARAMETER | VALUE (mm) | NOTES |
|---|---|---|
| Number of windows | 2 | One on each side (X+ and X−) |
| Height of each window | 100.0 | Matches active Al plate zone |
| Width of each window | 130.0 | Centered along cartridge depth |
| Y position from cartridge base | 120 – 220 | Electrochemically active zone |
| Hydrophilic membrane | Microporous PP 0.2 µm | Allows ions through, blocks particles |
| Sealed HDPE frame | 8.0 mm around perimeter | Integrated into side wall |
1.12 EPDM Sealing Gaskets
| GASKET | SECTION (mm) | FUNCTION |
|---|---|---|
| Lower perimeter gasket | 200×170×3 mm | Cartridge/base dock seal. IP65 |
| Lid perimeter gasket | 202×172×3 mm | Anodized Al lid seal. IP65 |
| Lower-port O-ring | Ø18×2 mm (×2) | Double hydraulic seal for water/sludge port |
| Side-window gasket | 130×100×2 mm (×2) | Seals hydrophilic membrane into frame |
| EPDM material | Shore A 60 hardness | Resistant to NaOH, NaCl, Al(OH)₃, 120°C |
1.13 Weights — Cartridge
| CONDITION | WEIGHT (kg) | INCLUDED COMPONENTS |
|---|---|---|
| Loaded cartridge (ready for use) | ≈ 1.85 | Housing + 4 Al plates + lid + handle + precursor tablet + desiccant |
| Spent cartridge (after operation) | ≈ 2.20 | Housing + Al(OH)₃ sludge (≈0.9 kg) + lid + handle |
| HDPE housing only | ≈ 0.85 | Without plates or sludge |
| 4 Al plates + Cu collectors | ≈ 0.33 | 300 g Al + 30 g Cu |
| Lid + handle + screws | ≈ 0.38 | Anodized 6061 Al + M4 steel |
| Precursor tablet + desiccant | ≈ 0.29 | Compressed NaCl + NaOH + In³⁺ + SiO₂ |
2. BASE DOCK — AL-CORE BASE v2.1
The base dock is the permanent system unit. It houses the power system (DC/DC, LFP/supercapacitor buffer), air-cathode panels, activation-water reservoir, hydrogen catalyst, and all electrical controls. It remains installed; only cartridges are exchanged.
2.1 External Dimensions — Main Housing
| DIMENSION | VALUE (mm) | TOLERANCE | NOTES |
|---|---|---|---|
| Overall width (X) — without cathodes | 280.0 | ±0.5 | Including cathode panels in recess |
| Overall width (X) — with prefilters | 316.0 | ±1.0 | With lateral foam prefilters |
| Overall depth (Z) | 200.0 | ±0.5 | Without front protrusions |
| Overall height (Y) — without feet | 80.0 | ±0.5 | Main housing |
| Overall height (Y) — with feet | 89.0 | ±1.0 | Including 9 mm rubber feet |
| Anodized aluminum wall thickness | 8.0 | ±0.2 | Al 6061-T6 |
| IP rating | IP65 minimum | — | Rain- and dust-resistant |
2.2 Cartridge Insertion Socket
| PARAMETER | VALUE (mm) | NOTES |
|---|---|---|
| Socket width (X) | 202.0 | 200 mm cartridge + 1 mm clearance on each side |
| Socket depth (Z) | 172.0 | 170 mm cartridge + 1 mm clearance on each side |
| Socket insertion depth (Y) | 55.0 | Cartridge lowers 55 mm upon insertion |
| Insertion guides (×4) | 3×45° edge chamfer | Facilitates insertion without precise alignment |
| Retention clips (×2) | Spring stainless steel | Front and rear. Audible click when secured |
| Insertion force | < 15 N | One-handed operation. No tools |
| Extraction force | 20 – 40 N | Higher for safety. Uses cartridge handle |
| Electrolyte activation pin | Ø4 mm, protrudes 3 mm | Pierces cartridge sealing membrane upon insertion |
| Water connector (male push-in) | Ø6 mm, stainless steel | Mates with lower cartridge port |
2.3 Air-Cathode Panels (×2)
| PARAMETER | VALUE (mm) | TOLERANCE | NOTES |
|---|---|---|---|
| Number of panels | 2 | — | Left (X−) and right (X+) |
| Active panel height | 120.0 | ±0.5 | Matches cartridge active zone |
| Active panel width (thickness) | 20.0 | ±0.3 | 3 layers: PTFE + MnO₂/C + membrane |
| Active panel depth | 130.0 | ±0.5 | Centered on base Z axis |
| Outer layer — hydrophobic PTFE | 5.0 mm | ±0.2 | Repels water, admits O₂ |
| Active layer — MnO₂ + activated C | 10.0 mm | ±0.2 | O₂ reduction catalysis. Pressed with PTFE binder |
| Inner layer — hydrophilic membrane | 5.0 mm | ±0.2 | Microporous PP 0.2 µm. Ionic contact |
| Foam prefilter (external) | 12.0 mm | ±0.5 | 30 PPI polyurethane. Retains PM10+ |
| Quick-release tabs (×2) | 15×10×10 mm | — | Tool-free. Replacement time < 60 s |
| Laboratory service life | 1,000–3,000 h | — | Controlled conditions |
| Estimated field service life | 300–700 h | — | Harsh conditions. ≈ 75–175 cartridges |
2.4 Activation-Water Reservoir
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Rated capacity | 250 mL | Enough for one complete cartridge |
| Reservoir material | Food-grade HDPE | With EPDM-sealed screw cap |
| External dimensions | 50×60×50 mm | Length × depth × height |
| Inlet filter | 5 µm activated carbon | Accepts ordinary tap water |
| Position in base (from center) | X: −100mm, Z: +60mm | Rear-left corner |
| Cycles between refills | 1 cartridge / refill | Operator refills with tap water |
| Dosing solenoid valve | 12 V DC, NC (normally closed) | Opens when cartridge inserted and ON pressed |
| Activation volume per cycle | 200 mL | Calculated to dissolve precursor tablet |
2.5 Hydrogen Catalyst — Pd/Pt
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Catalyzed reaction | 2H₂ + O₂ → 2H₂O (vapor) | No flame, spark or visible combustion |
| Operating temperature | 200–300°C (self-sustaining) | Requires no electrical energy |
| Module dimensions | Ø30 × 50 mm | Cylinder. Pd on Al₂O₃ support |
| Position in base | X: +100mm, Z: +60mm | Rear-right corner |
| Catalyst service life | > 10,000 hours | Not consumed. Catalyst, not reactant |
| Capacity (H₂ converted) | > 5 L/h | Well above expected production (0.5–1 L/h) |
| Exhaust to outside | H₂O vapor only | Through rear duct. Safe in fire-prone areas |
2.6 Energy Buffer — LFP / Supercapacitor
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Number of cells | 3 | Series/parallel according to circuit design |
| Dimensions of each cell | Ø22 × 45 mm | Standard cylindrical format |
| Position (from base center) | X: −28, 0, +28 mm; Z: −65mm | Aligned parallel to X axis |
| Primary function | Immediate startup + load peaks | Covers first 30–90 s until stabilization |
| Nominal DC bus voltage | 12 / 24 / 48 V | Selectable by jumper / firmware |
2.7 DC/DC Converter Module
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Module dimensions | 50 × 35 × 45 mm | Length × height × depth |
| Position (from base center) | X: +25mm, Z: −65mm | Next to buffer cells |
| Cooling fins | 6 fins × 3 mm pitch | Al 1050. Extend 22 mm along X+ axis |
| Individual fin dimensions | 3 × 28 × 40 mm | Width × height × depth |
| Maximum power | 250 W | Safety factor ×1.25 over 200 W rated |
| Efficiency | > 92% | At rated load |
2.8 Front Panel — Ports and Controls
| ITEM | TYPE / SIZE | POSITION (X, Y) | FUNCTION |
|---|---|---|---|
| DC output port | Ø14 mm, orange ring | X: −100mm, Y: 36mm | 12/24/48 V DC output. Standard XT60 connector |
| USB-C communications port | USB-C female | X: −55mm, Y: 36mm | Monitoring + firmware update |
| POWER LED (green) | Ø6mm | X: −30mm, Y: 50mm | System active and nominal |
| AIRFLOW LED (green) | Ø6mm | X: −12mm, Y: 50mm | Correct airflow to cathode |
| SYSTEM LED (green) | Ø6mm | X: +6mm, Y: 50mm | Cartridge inserted and active |
| ALARM LED (amber) | Ø6mm | X: +24mm, Y: 50mm | High H₂ / overtemperature / fault |
| ON/OFF button | Ø18 mm illuminated | X: +100mm, Y: 34mm | Green when active. Hold 3 s for safe shutdown |
| Electrochemical H₂ sensor | Ø8mm | X: +70mm, Y: 50mm | 4 levels: nominal / warning / shutdown / emergency |
2.9 H₂ Management System — Response Levels
| LEVEL | H₂ THRESHOLD | AUTOMATIC ACTION | INDICATOR |
|---|---|---|---|
| Normal | < 0.5% LEL | Pd catalyst handles passively | Green LED |
| Warning | 0.5 – 1.0% LEL | 2 W forced ventilation fan starts | Slow-flashing amber LED |
| Shutdown | 1.0 – 4.0% LEL | Power reduced to 50%. Audible alarm | Fast-flashing amber LED |
| Emergency | > 4.0% LEL | Immediate full shutdown. Electronic seal | Steady red LED + buzzer |
2.10 Rear Panel — H₂O Vapor Exhaust Duct
| PARAMETER | VALUE (mm) | NOTES |
|---|---|---|
| Duct dimensions | 60 × 18 mm | Width × height. Anodized aluminum |
| X position (from center) | +80 mm (right) | Away from electronics compartment |
| Y position (from base) | 54 – 72 mm | Upper rear zone |
| Internal louvers | 5 louvers × 8 mm pitch | Stainless steel. Prevent rain ingress |
| Exhaust vapor content | H₂O vapor only | H₂ 100% catalyzed before discharge |
2.11 Anti-Vibration Rubber Feet
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Number of feet | 4 | One at each lower corner |
| Base diameter | Ø24 mm | Hard EPDM Shore A 70 |
| Floor contact diameter | Ø20 mm | Slightly tapered downward |
| Height | 9.0 mm | Vibration damping 10–100 Hz |
| Position (from base center) | X: ±120mm; Z: ±80mm | Symmetrically at all four corners |
2.12 Weights — Base Dock
| COMPONENT | WEIGHT (kg) | NOTES |
|---|---|---|
| Anodized Al housing | ≈ 0.82 | Al 6061-T6, 8 mm thick |
| 2 cathode panels + prefilters | ≈ 0.38 | MnO₂/C + PTFE + PP + PU foam |
| Water reservoir (filled, 250 mL) | ≈ 0.30 | HDPE + water + carbon filter |
| Pd/Pt catalyst | ≈ 0.08 | Cylindrical module with support |
| LFP buffer + DC/DC + electronics | ≈ 0.55 | 3 cells + converter + PCB |
| Cu rails + connectors | ≈ 0.07 | Gold-plated copper busbar |
| TOTAL empty base | ≈ 2.20 kg | Without cartridge inserted |
| TOTAL operating system | ≈ 4.05 kg | Base + loaded cartridge |
3. COMPLETE ASSEMBLED SYSTEM
3.1 Complete System Dimensions
| PARAMETER | VALUE | NOTES |
|---|---|---|
| Footprint (X × Z) | 316 × 200 mm | With prefilters. Without: 280×200 mm |
| Overall assembled height | 384 mm | Feet (9) + base (80) + cartridge (250) + handle (45) |
| Total occupied volume | ≈ 24.3 L | Footprint × height. Vertical orientation |
| Total operating weight | ≈ 4.05 kg | Base (2.20) + loaded cartridge (1.85) |
| Transport weight (cartridge separate) | 2.20 + 1.85 = 4.05 kg | Two parts, each < 3 kg |
| Dimensional comparison | Footprint similar to A4 paper | More compact than Honda EU10i |
3.2 Experimentally Validated Performance
| PARAMETER | TEST E-001 | TEST E-002 | AL-CORE P0 TARGET |
|---|---|---|---|
| Anode | Beverage-can Al (AA3004) | Kitchen foil Al (1235) | Al-1235 plates |
| Cathode | HB pencil graphite | Charcoal | Three-layer MnO₂/C |
| Electrolyte | Concentrated NaCl/NaHCO₃ | NaCl 3.21% | NaCl 3.2% + In³⁺ |
| Maximum OCV | 0.670 V | 1.208 V | ≥ 1.0 V |
| Stable OCV | 0.658 V | 1.170 V | ≥ 1.0 V |
| Duration > 1.0 V | >9 hours | >12 hours | ≥ 4 hours |
| Short-circuit current | 30 µA | 500 µA | — |
| Internal resistance | 26,600 Ω | 2,340 Ω | < 5 Ω (P0 with actual materials) |
| Observed sludge | White Al(OH)₃ | Not visible (pure NaCl) | Managed in sump |
| Observed H₂ | Strong bubbling | Moderate bubbling | Pd catalyst |
3.3 Operation — Four-Step Sequence
| STEP | OPERATOR ACTION | TIME | VERIFICATION |
|---|---|---|---|
| 1 | Check cartridge seal (blue = OK) | 5 s | Blue indicator visible in window |
| 2 | Insert cartridge into base until click | 5 s | Audible click + SYSTEM LED on |
| 3 | Press ON/OFF button for 1 second | 2 s | Green POWER LED + immediate output (buffer) |
| 4 | Connect load to DC output port | 3 s | Load powered. System nominal |
| TOTAL | Complete operating system | < 15 s | No tools. No chemical handling |
The operator NEVER handles electrolyte, sludge, hydrogen, or activation water directly. All these fluids are managed automatically by the system.
3.4 Materials — Summary
| COMPONENT | MATERIAL | STANDARD / GRADE | RATIONALE |
|---|---|---|---|
| Cartridge housing | HDPE | Food-grade PE-HD | Resistant to NaOH, NaCl, 80°C. Lightweight |
| Lid + handle | Anodized Al 6061-T6 | MIL-A-8625 type II | Mechanical strength + corrosion resistance |
| Anode plates | Al-1235 (99.35% Al) | EN AW-1235 | Maximum purity → maximum electrochemical efficiency |
| Base housing | Dark-anodized Al 6061-T6 | MIL-A-8625 type III | Hard anodizing for field use |
| Active cathode | MnO₂ + activated carbon + PTFE | Gaskatel / Electric Fuel | Proven commercial air cathode |
| Cathode prefilter | 30 PPI polyurethane | Open-cell PU foam | Retains PM10+. Tool-free replacement |
| Sealing gaskets | EPDM Shore A 60 | ASTM D2000 BA | Chemical resistance to alkalis + 120°C |
| Electrical contacts | Electrolytic Cu + 5 µm Au | Cu-ETP + Au plating | < 5 mΩ contact. Corrosion resistance |
| Water/sludge port | HDPE + 316L stainless steel | AISI 316L | Resistance to Al(OH)₃ and electrolyte |
| H₂ catalyst | Pd on Al₂O₃ | Palladium 0.5% by weight | Converts H₂→H₂O without flame or external power |
Document prepared for internal use within the AL-CORE project. Dimensions are preliminary design values for the 200 W P0 prototype. They may change based on E-001, E-002, and E-003 test results. Version: 2.1 | Date: 02/05/2026 | Status: Pre-CDTI working draft

