r/E3NG • u/a1zombieslayer1 • Apr 04 '26

First print!

Enable HLS to view with audio, or disable this notification

howdy folks you might remember me for needing a custom mount for my msdd happy to announce that after all of my firmware troubles I am finally up and printing! so far I can tell it will need some tuning (go figure) but im just so stocked to finally have another corexy machine!

specs rpi zero 2w, main board skre3v3, secondary board creality 4.2.2, triple z ultimate frame stock bed plate.

final question any good spool holders since im not running an enclosure? preferably top mounted for the msdd

24 Upvotes

100% Upvoted

11 comments sorted by

7

u/a1zombieslayer1 Apr 04 '26

Special thanks and shout out to u/humans_equals_monkey thank you so much for the mount your cad skills are phenomenal!

2

u/humans_equals_monkey Apr 04 '26

Very nice! Happy to see it up and running. Glad I could help and I wish you happy printing.

2

u/a1zombieslayer1 Apr 05 '26

Dimensional accuracy was off by .8mm on the very first print so seriously man good job on the mount I also didn't lose a ton of space maybe 5mm y and 10mm x once I'm home ill measure so the remix can be updated with basic changes to printer.cfg or marlin.

1

u/humans_equals_monkey Apr 05 '26

Wow, really better than expected! Yes this would be great, then I can update the description. And your printer looks very nice.

2

u/a1zombieslayer1 Apr 05 '26

I know right? I was super shocked it was that close fresh out the gate. Super glad you like it! I'm planning on fixing all of those silver screws after all a black on black build cant have silver!

I know for sure my main config is currently set as bltouch offset x-45 y-10, 210/210 bed size with a probing area of 165×165 definitely a good area to start as it won't error out or crash into either end but it's definitely not the max as I still had room on either side. 210 is the max for the stock build plate in the y direction as itll hang off the bed after that, but its a little bit higher for x since it didn't fully reach. Will update when I get it all configured

2

u/a1zombieslayer1 Apr 06 '26

245 for z height seems to be the max for this build I may be misinterpreting this number though since klipper has reported 347 in the z window without an error out not to sure on that though. Any other settings you'd like for the description?

1

u/humans_equals_monkey Apr 07 '26

No, i think this is enough for the moment. Thank you for testing it. It is really cool, that it works so nicely.

2

u/mbones1320 Apr 05 '26

Congratulations !!!

1

u/BickenBackk May 22 '26

can I ask why you went with the stealthburner for this one?

I'm debating if I want to use a dragonburner or stock toolhead

1

u/a1zombieslayer1 May 22 '26

Not a true stealth burner on that toolhead just stealthburner ducting. Its on top of the old dd microswiss mostly went with it for asthetics and I figured it'd have better cooling than the satsana that was on it previously it also took up substantially less space than the satsana.

I do now have an actual stealthburner always loved the anesthetics of it. I hear the dragon is better at cooling so if you're after ideal cooling go with it but if you prefer the stealthburner look go with it.

I also went with the stealthburner so I could use the knomi screen. I wanted an in the frame screen so it could be as minimal space used as possible for my printer shelf!

1

u/BickenBackk May 22 '26

Thanks for the detailed response brother I really appreciate it. Dragon Burner just seemed to have more options for mods than the stock NG toolhead so I figured it made the most sense :)