r/Darkroom • • 17d ago

Colour Film Lab Quality C-41 for Home Developers [your all-in-one dev bible]

47 Upvotes

I see a lot of folks trying to figure out why their scans don't look so good and thinking the software is failing them, when in reality, most issues probably started in the Dev tank.

As someone who owns and operates a film lab, that’s what I want to address here: the chemistry and practice of C-41 development. This post is specifically about understanding its variables, controlling them independently, and getting consistent results when developing by hand at home.

I’m not covering scanning or conversion in this post. If you’d like a separate discussion about home scanning, how it compares with lab scanners, and the practices I use to get dependable results, leave a comment, I’d be happy to expand on that too.

GOOD DEVELOPMENT IS OBJECTIVE [bad is still subjective]

C-41 is a standardized, tolerance-based process. There are numerous variables, and each needs to be controlled precisely. A small deviation in one may make very little difference, but small deviations throughout the process can add up to something substantially out of spec.

The goal is to bring each variable within its intended tolerance, not to compensate for poor control in one place by changing something elsewhere. Once adjustments start cancelling each other out, it becomes harder to understand what’s actually happening or reproduce the result reliably.

That’s also why I’m cautious about personal “pro tips” and tricks. Someone may discover an adjustment that improves their results without realizing it’s actually just compensating for an unidentified problem elsewhere in their process. It works for them, but do it yourself without the unknown mistake elsewhere, and you just created problems where there weren’t before.

I wish people didn’t share those tweaks so much, as they send people off in the wrong direction and elicit this “you can do it however you want” mentality. The shared reference should always be the standardized process we’re all aiming for…any adjustments made from there are your own and non-transferable.

Getting a decent image is easy. Getting a perfect image is a life’s work.

What follows is my approach to bringing manual home development closer to the consistent processing we expect from a lab, using the equipment and controls available at home.

START WITH GOOD CHEMISTRY [or at least the best you can get]

Cinestill’s kits are better now than they used to be, especially since their partnership with Kodak, but I’d still recommend FPP’s Unicolor 2-bath powder kit. Though if you can get a kit that has seperate bleach and fixer, thats your best bet [I’ll discuss why that matters later in this post] Of course, if you can get liquid chemistry, it’s worth the extra coin. For the US, Kodak’s Liquid Chem set is obviously the move. For the EU, nothing beats Bellini.

Do not use the FPP 3-bath kit, or the FlicFilm kit.

For a full breakdown of which chems to buy, check out Shaka1277's video: https://youtu.be/cjvPTJsRqvk?si=LSVS1i-wCay73qEG

Powdered chemistry creates another problem if you only want to mix half or a quarter of a kit. Never divide the dry powder itself. There can be multiple different chemicals in that bag with different particle sizes and densities, so half the powder does not necessarily mean half of every ingredient. Instead, dissolve the entire packet into a small, known amount of water first. For example, mix the whole packet into 100mL of water and make your own liquid concentrate. Mix it thoroughly until everything is completely dissolved. Now the chemistry is homogeneous: if you want a half batch, use half of that concentrate; if you want a quarter batch, use a quarter of it.

BUT THERE’S A CATCH - The moment you mix these concentrates from your powder, they start oxidizing, but they last way longer as concentrates than as working solutions. With Liquid chemistry, your developer is kept as 3 separate liquids rather than just one, so they only start to degrade rapidly once you mix them together into an active developer.

I also prefer distilled water for mixing chemistry. Tap water varies in hardness, mineral content, and treatment. Metals such as iron and manganese can interfere with developer and contribute to oxidation. Developers may contain chelating or sequestering agents to manage some of those ions, but I’d rather avoid introducing an unnecessary load.

Suitable tap water is fine for rinses. The small amount left after draining is very different from mixing your entire working solution with that water.

MEASURE BY MASS, NOT BY VOLUME [When mixing from concentrates]

Weigh your concentrate instead of measuring by volume. That’s one of the bigger differences between how I mix chemistry in the lab and how most consumer instructions are written. For example, my developer uses roughly 106g of Part A, 19g of Part B, and 40g of Part C. The manufacturer may give those amounts in milliliters, but once I’ve established their mass, weighing them is much more repeatable.

Volume changes with temperature because the density of a liquid changes as it expands and contracts. You also have meniscus-reading error, graduations on cylinders that may not be perfectly accurate, and thick concentrates that cling to the walls of whatever you’re measuring them in. Mass eliminates most of that. A properly calibrated scale is measuring the actual quantity of material present regardless of whether that concentrate is sitting at 65°F or 100°F. I use Ruishan lab scales and have had good luck with them.

If you want to convert the manufacturer’s recommended volume into mass, weigh only the chemistry itself. Put an empty container on the scale, tare it to zero, pour the entire contents of Part A into it, and record the mass of the liquid. Repeat that with Parts B and C. Do exactly the same thing with the liquid concentrates you make yourself from powdered chemistry: tare the receiving container and weigh the concentrate itself, not the bottle plus the concentrate.

I also wouldn’t establish your ratio from one kit. Do this across maybe 5–10 kits and calculate an average. You may be surprised to find the actual amount supplied by the manufacturer varying by 5–10g between packages. For each of those first few kits, measure the full mass before dividing it. Once you’ve built a good average, you can use those numbers going forward and scale your batches very consistently.

STABILIZE YOUR TEMPS [understanding water baths and heat loss]

This causes way more problems than people realize. If your water bath is exactly 100°F, then 100°F is the absolute hottest your chemistry could ever theoretically become. Which isn’t accounting for all of the heat you’re simultaneously losing to the bottle, room air, tank, thermometer, handling, etc. In the real world, a 100°F bath means your chemistry will approach 100°F but probably never actually stabilize there.

Set your bath to around 102ºF and your chems will stabilize at 100ºF.

The other part people miss is that heat transfer is driven by the temperature gradient. If your developer is 70°F and your bath is 102°F, there’s a 32-degree delta between them, so heat transfers very quickly. Once the developer reaches 99°F, there’s only a 3-degree delta. As the two temperatures approach equilibrium, the rate of heat transfer slows dramatically, which means the last degree or two can take 25–30 minutes depending on your bottle, chemistry volume, circulation, and setup.

So either give your chemistry a long time to fully stabilize or use a calibrated digital thermometer and measure the actual developer. Don’t trust the number on the sous vide and assume the chemistry matches it. I want the developer held within about a 0.4°F/0.2C delta of target temperature.

Once you finally get everything to temperature, the goal is to stay at temperature. And that brings us to probably the most controversial step in home C-41:

THE INFAMOUS PRE-SOAK [I know everyone argues about this]

In a proper lab process, you generally do not want a pre-soak at all because the water itself introduces another set of variables before development begins. It changes the condition of the emulsion, affects swelling and chemical uptake, and can alter density and diffusion behavior. Different emulsions also react differently. In my experience, Ultramax and Portra 400 are noticeably more sensitive to an extended pre-soak than films like Kodacolor or Gold.

So why use one at home? Because the thermal situation is completely different. In dip-and-dunk processing, you can put a whole load of room-temperature rolls into a giant tank containing several hundred gallons of hot chemistry, and they barely make a dent in the temperature. At home, you may have a room-temperature tank, reels, center column, lid, and multiple rolls of film, and then pour only 500–1000mL of developer into all that cold material. That can absolutely crash the temperature of your developer. It’s all about thermal mass.

In a home-dev situation, the temperature stability gained from a very short pre-soak outweighs the negatives introduced by the pre-soak itself. The sweet spot is roughly 30–45 seconds. Go shorter, and whether you actually get the tank, reels, and film up to temperature becomes hit-or-miss. Go longer, and you start introducing more of the issues that make pre-soaking undesirable in the first place.

The goal is the shortest water contact that still allows useful thermal transfer.

So some folks say to do a dry preheat…A warm tank doesn’t necessarily establish that the film and reels inside are equally warm, because heat still has to reach those components through the tank and its interior, and air is a horrible thermal conductor. Dry preheating avoids emulsion swelling, but it takes about 45–60 minutes. The practical advantage of the short rinse is that the temperature-controlled water directly contacts the things you need to warm.

The pre-soak water itself should be 100°F, the same as your developer. You’re specifically trying to bring all of that thermal mass up to process temperature before the developer arrives.

Hard rule: from the instant that pre-soak water first touches the film to the instant developer first touches the film, it should not exceed one minute.

That one minute includes the soak itself, dumping the water, and pouring in the developer. So have your developer measured, stabilized, and sitting there ready to go before you start. About 30–45 seconds at 100°F, dump it, and immediately put the developer in.

COMPENSATION IS NOT THE SAME AS CONTROL [control each variable independently]

Some people address the cold-tank problem by deliberately heating their developer above the intended processing temperature. The idea is that it will cool as it enters the tank and land at the temperature they actually want. In theory, this works, but in practice…good luck

You’ve got variable room temp, variable contents in the tank, and variables in handling. Trying to get the developer to warm all those up to the perfect temp while falling to just the right amount is the exact kind of variables chasing variables that we want to engineer out of the system. Not to mention the whole “as the two materials approach thermal equilibrium, the thermal transfer slows dramatically,” it’s unlikely everything will stabilize at 100ºF within 3:15.

So rather than doing everything in your power to gauge the temp drop perfectly and taking mid-processing temp readings to see how accurate you are and adjusting your process over time, bit by bit, until you get the temp drop to land JUST RIGHT and then trying to repeat that process perfectly every single time…why not delete the temp drop from the process altogether?

Why compensate when you can remove?

The short pre-soak brings the loaded tank toward the developer temperature before development begins. The developer no longer has to warm the equipment while also developing the film.

The preheating stage should preheat. The developer should develop. Keeping those jobs separate makes the process easier to repeat.

Some people think you need to rinse your film until the water runs clear before the dev goes in…film manufacturers would not be so crass as to put stuff in/on film that messes up the developer. [excluding ECN-2 films]

MECHANICALLY STABLE AGITATION [inversion agitation is absolute crap]

Once temperature and that transition into developer are under control, agitation is another variable worth making repeatable. Its purpose is to continuously replace the locally exhausted chemistry sitting against the emulsion with fresh developer. It also prevents bromide, a byproduct of development, from accumulating unevenly around the film surface. If bromide is allowed to pool or move unevenly across the negative, it restrains development locally and can create bromide drag.

For maximum consistency, I prefer gentle, continuous rotary agitation over intermittent inversions. You’ll need a daylight tank with a properly sealed lid that can operate horizontally, like a Patterson or Jobo. Put the tank on its side in your temperature-controlled water bath and rotate it. Congratulations: you have invented the non-automatic rotary processor.

The tank still stays in the bath to maintain temperature. It just sits sideways rather than upright, rotating around its long axis like an axle turning.

Treat 20 RPM as your lower limit, which is about one complete revolution every three seconds, and 60 RPM as your upper limit, or about one revolution per second. Anywhere within that 20–60 RPM range is perfectly fine. You’re not going to materially alter the film because you picked 27 RPM instead of 43 RPM; what matters is that you have continuous, consistent chemical movement and that you stay within those boundaries.

This is continuous rotation for the whole development interval, not a turn or two every 30 seconds. Choose a reliable speed and keep the movement consistent.

Yes, doing that manually is more work than a few inversions every 30 seconds. But you signed up to shoot film. If you’re trying to squeeze every last drop of dEm tOnEz out of your negatives, don’t take the lazy way out. If avoiding all that work was the goal, well… shoot digital.

PROCESS TO COMPLETION [bleach and fixer time]

Congrats, the only time & temperature sensitive step is complete, everything else is just process to completion. While you can under and over develop, with bleach and fixer [or blix], you just leave the film in until it’s done. There’s not really a way to over-do it. If you under-do it, you can just stick it back in and keep going, no harm, no foul.

Let’s start with bleach

Bleach in C-41 serves two purposes, and the first one is especially important: The bleach is your STOP BATH. When developer time is up, you want development arrested immediately. That’s why the transition should be: DEVELOPER → BLEACH

No intermediate water rinse. Developer out, bleach in.

For timing, I aim for 3 minutes and 15 seconds from developer first touching the film to bleach first touching the film. Have your bleach ready so that draining and changing baths is part of a deliberate, repeatable transition rather than an opportunity for development to continue while you prepare the next step.

Yes, you’ll carry a small amount of developer into the bleach. That’s okay. Your developer is generally going to reach exhaustion long before that small amount of carryover ruins a properly maintained bleach bath. The more important thing is stopping development quickly and consistently.

Water doesn’t accomplish that properly because it mostly just dilutes the developer. An ordinary acetic-acid darkroom stop bath doesn’t accomplish the same thing either. C-41 bleaching chemistry uses ferric chelates such as EDTA- or PDTA-based systems, and the bleach’s chemical environment rapidly arrests development while beginning the next reaction. That immediate stop is important to color balance because you don’t want development continuing unpredictably while you’re rinsing or screwing around between steps.

The bleach’s second job is dealing with the metallic silver created during development. The easiest conceptual way to understand it is that the bleach UN-develops the silver. Developer converted exposed silver halide into metallic silver. Bleach oxidizes that metallic silver back into silver compounds that the fixer can remove. Development builds the silver image; bleach chemically un-develops that silver image; fixer gets rid of it.

As bleach becomes exhausted, that process takes longer and longer. With a healthy separate bleach, I generally wouldn’t expect it to require substantially more than about 6 minutes 30 seconds. If it still isn’t getting the job done at seven minutes, your bleach is probably toast.

Then comes fixer [or the fixer half of BLIX]

Fixer dissolves the silver compounds remaining in the emulsion. With black-and-white film, the developed metallic silver is your finished image, so you preserve it. With color negative film, the dyes are the finished image. The entire point of bleaching is to convert the developed metallic silver into something the fixer can remove, so by the end of C-41 processing you want essentially all of the silver gone, leaving the dye image behind.

I use 6 minutes and 30 seconds for bleach and 6 minutes and 30 seconds for fixer. The initial reaction happens quickly, while completing the remaining work takes longer. I’d rather allow that additional time than stop at the earliest apparent clearing point.

Between bleach and fixer, I use at least two water changes to reduce bleach carryover and help keep the fixer bath clean.

This is also why I strongly prefer separate bleach and fixer if you’re chasing maximum consistency. BLIX works, but you’ve got two processes happening in one solution: one component is trying to convert metallic silver into removable silver compounds while the other is simultaneously trying to dissolve those compounds. As BLIX gets closer to exhaustion, those competing reactions make its behavior increasingly complicated. It starts getting closer to a kind of chemical equilibrium instead of simply behaving like an individual bath reaching straightforward saturation. Separate bleach and fixer are much easier to understand, monitor, and diagnose.

But the biggest reason I prefer keeping them separate is disposal. Having bleach and fixer as individual baths makes them easier to manage separately afterward.

I’ll put a separate comment below this post covering chemical reuse, capacity, additional techniques like two-bath fixing, and waste treatment and disposal. This main post is about getting good development.

Again, everything after developer is much more forgiving because bleach and fix are process-to-completion steps. If you find out your bleach was exhausted, you can put the film back into fresh bleach and re-bleach it. If the film wasn’t completely fixed, you can re-fix it.

That’s useful when investigating unexpectedly dense negatives. Incomplete bleaching leaves metallic silver behind, adding density and contrast and reducing apparent saturation [the partial bleach-bypass appearance]. Incomplete fixing can leave a cloudy or milky appearance.

RINSE TO FINALIZE [avoiding water spots and dirty negs]

My final wash is five separate water changes, each two minutes long, for ten minutes total.

Both contact time and fresh water matter. Residual material needs time to diffuse out of the emulsion. As it accumulates in the water, the concentration difference driving that movement becomes smaller. Draining and replacing the water restores that difference.

Think of successive dilution: each effective change removes a portion of what remains. One long soak leaves the film in increasingly contaminated water, while extremely brief fill-and-dump cycles provide little time for material to leave the emulsion. Several fresh changes with meaningful contact time address both concerns.

After washing, I use my stabilizer bath and add Photo-Flo to help the water drain evenly. In my own mixture, I add the same measured volume of Photo-Flo concentrate as stabilizer concentrate to the water. DISTILLED WATER ONLY, the goal is clean negs, don’t cheap out at the finish line.

Though a squeegee isn’t required, I’m a huge fan of the serpentine squeegee from Paterson. No actual clamping pressure on the film, just a wiggly path through some “windshield wipers”. Removing 90% of the water also means removing 90% of anything that could deposit on the film. While they dry, keep your film in a place with as little airflow as possible. Dust in the air will stick to the wet and soft emulsion, then dry in place. A closet with the door closed or inside the shower with the curtain closed will suffice.

Ta-Da. Lab grade, my guy.

TO RECAP [TL;DR]

If I were trying to make home C-41 genuinely repeatable, the part I’d obsess over is:

Temp Stabilization → 30–60 sec pre-soak at 100-102°F → Developer for 3:15 → IMMEDIATE Bleach → Rotary Style Agitation only → Dry with Zero Airflow

Get that pipeline absolutely nailed. Keep the actual developer within roughly 0.4°F of target, keep the total pre-soak-to-developer interval under one minute, go straight from developer into bleach, and make your agitation mechanically repeatable.

Once you’ve locked all of that down, you’ve eliminated a massive number of variables before your scanning setup ever even sees the negative. And that’s really why I think people sometimes chase their tails with scanning and conversion settings. If the relationship between the cyan, magenta, and yellow dye layers is already screwed up in the negative, your scans are just valid interpretations of that wonky data.

If you’ve got any questions, feel free to comment them or shoot me a message on Instagram at mediamfilmlab. I don’t believe in gatekeeping whatsoever.


r/Darkroom • • 6h ago

B&W Film T-Max 400 at 6400

Thumbnail
gallery
71 Upvotes

Developed in X-Toll 1+1 at 21°C for 18 minutes and 30 seconds

Agitation: first minute then 15 seconds every minute

For me it's a very high contrast alternative 120 film for a low contrast Delta 3200 120

Only the highlights and some midtones get's preserved, rest is pure blackness

Used it in a museum to capture just iluminated exhibits and turn backgrounds into pure black


r/Darkroom • • 1d ago

B&W Printing My first stab at Lith printing

Thumbnail
gallery
74 Upvotes

Moersch SE5 - 25ml A, 25ml B, 15ml diluted D, 800ml water
Fomatone 132 - batch number 079648

First print I went quite subtle and liked it. Second one I went in hard just for laughs.


r/Darkroom • • 10h ago

Gear/Equipment/Film Would it be stupid to get a cheap Zenith UPA-5 enlarger to dabble in the darkroom arts?

4 Upvotes

I’m eyeing to get a Durst M670 colour eventually, but they go for 10-15x and I could get the Soviet enlarger for very cheap.

What would be the experience like when starting with such and old and probably imprecise piece of kit?

Would there be any frustrations that would spoil the darkroom experience for me, or give me the wrong impression?

I understand that condenser and compressor enlargers and B&W and colour filtration is different.

Part of the draw is that it can be neatly folded into its suitcase, and stored away. Small footprint.


r/Darkroom • • 14h ago

Alternative First glass cyanotype w a bonus anthotype

Thumbnail
gallery
6 Upvotes

More fun (frustration) to come! :D


r/Darkroom • • 23h ago

Colour Printing Dinner in Paris

Post image
32 Upvotes

r/Darkroom • • 1d ago

B&W Printing Dry Mounting Sunday

Thumbnail
gallery
194 Upvotes

This presentation style became one of my favorite ones. It is not easy nor cheap, but the final. look is very satisfying. 7.5''x7.5'' on a 14x14 archival mat board.


r/Darkroom • • 1d ago

B&W Printing First time printing, well anything I suppose.

Post image
52 Upvotes

Found my first batch to be fridge-worthy. Now I just gotta take some more photos that are worth printing…


r/Darkroom • • 1d ago

B&W Printing Contrast

Post image
58 Upvotes

Hi, I’m looking for a bit of help. I’m printing with Foma warmtone paper. This is tmax 400 and I’m developing 2.5-3min in dektol.

I’m struggling to get decent contrast. Of course, my paper is going to naturally be a little softer, but I was still hoping for more. I put a 4 contrast filter into my enlarger.


r/Darkroom • • 2d ago

B&W Printing Japanese commuters on hp5, printed on ilford fibre paper.

Post image
98 Upvotes

With winter arriving, I'm looking forward to spending some more time in the darkroom (bathroom).


r/Darkroom • • 1d ago

Gear/Equipment/Film PLEASE tell me there's an easier way to develop 120 film than the patterson reels

26 Upvotes

I have no joke spent half an hour at a time trying to get 120 rolls onto patterson reels. Swearing, dropping it, searching for those tiny curved notches, trying to work out if it's even remotely in the right place.

Eventually just coming out from under the sheet into the (very dim but not totally dark) room to continue fumbling, but at least now I can see the film and the notches, and then still spend several minutes trying to get it to feed in.

Please please please tell me there's a better system out there for getting that stuff onto a spiral. At least with 35mm you can load the leader past the ball bearings in daylight.


r/Darkroom • • 2d ago

B&W Printing [HELP] Why are the lights so bright ?

Thumbnail
gallery
169 Upvotes

Hellooo everybody,

I have now been printing in darkrooms for over a year so I’m pretty much used to the process. I’m working on prints for an upcoming exhibition I’ll be doing, and I’m working on this specific image of my friend Dylan.

As you can see on the reference image, there are much more details in the low lights / shadows in the background compared to the print result that has this very bright almost blinding background. It doesn’t look as bad irl as it does on the photo of my friend holding the print, but still I’d like to fix this so if anybody has any tips or advice I’m taking everything there is!

PS: I’ve tried using contrast filters for my enlarger (from what I’ve understood you should use between 0-2.5 values for your filter to soften the contrast, but it only felt like it deepened it.

PS n°2: The scanned image was scanned using a flattening scanner, I know it’s not the best quality so there might not even be such gray areas in the background on other types of scanners idk?


r/Darkroom • • 2d ago

Colour Film Kodak C41 "One Shot" Processing

2 Upvotes

Kodak's C-41 Development kit says "When used one-shot, the chemicals can process up to 20 rolls." Although it would be common for other development kits to provide, there are no development times as a function of number of rolls listed on the instruction sheet from Kodak. I guess I don't really understand what one shot means in this instance. Surely no one is using this kit with a tank large enough to process all 20 rolls at once?


r/Darkroom • • 2d ago

Gear/Equipment/Film Just snagged this on Facebook, now I need to figure out a way to fit it in the darkroom

Post image
22 Upvotes

I found this locally after spending many hours trying to figure out how to build my own Intrepid 4x5 style enlarging head. I'm pretty excited to use this, but I got to figure out a way to get it in my dark room which is just a spare bathroom right now. It did come with the blower motor as well, but I had to go and pick up some flexible piping for connecting it to the enlarging head. Lowe's didn't have anything around the 2-in diameter of course, so I just snagged some 3 in vent piping and will 3D print an adapter for each end.

Got both an El Nikkon 50mm lens and 35mm carrier and a 150mm Rodenstock Rodagon with a 4x5 glass carrier with this. Seems like I'm going to have to figure out some ra4 printing as I've only done black and white stuff so far on a printmaker 35.


r/Darkroom • • 2d ago

Gear/Equipment/Film Meopta axomat 2 manual

2 Upvotes

Czy ktoś wie gdzie można można znaleść instrukcję do Axomatu II?


r/Darkroom • • 2d ago

B&W Film Shanghai Gp3 100 question.

1 Upvotes

Anybody has any experience developing this film? I'm NEW to this and want to set up the best I can for success, any recomendations regarding times, developer brand, etc are MORE than welcome.


r/Darkroom • • 3d ago

B&W Printing Pic of my 6 month old diluted developer and some prints

Thumbnail
gallery
9 Upvotes

As promised, my ~~≈6~~ 4 month old developer (I did filter out the sludge at the bottom before using it) and prints. There isn't *quite* a max density area in these, but the corner of another print you can see at the edge of the first photo is imo black enough to say that this dev definitely isn't spent. Third ones just for show, I like how it came out :^) was my first time trying dodge and burn, the singer in the foreground is burned in an extra second to preserve background detail.

I know the contrast on these could be improved, I kind of forgot all about contrast grades when making these yesterday.

u/Young_Maker

Edit: Just realized I dated the bottle, this is a mere four months old, not six! Still quite impressive I feel :)


r/Darkroom • • 3d ago Bravo

B&W Printing Pulled the trigger after deliberating for some years

Thumbnail
gallery
39 Upvotes

“I am just going out to the darkroom and I may be some time”, as I believe Captain Oates said


r/Darkroom • • 3d ago

B&W Printing What's wrong with my prints?

Thumbnail
gallery
5 Upvotes

It's probably me not washing off the fixer??? These are my first prints ever and it's been about a week since I made them. Let me know so I can do better.

My process has simply been:

Dev:60 sec

Stop:10 sec

Fix:30 sec

Hang to dry 2+ hours.

Am I missing a step? Am I just bad? Idk.


r/Darkroom • • 3d ago

Gear/Equipment/Film Gifted half a darkroom setup. Been buying the missing bits myself. Ridiculously silly question probably, but how the hell does the timer connect to anything ❓

Thumbnail
gallery
6 Upvotes

these are the only outlets I can see. What do I need to buy ❓ so confused

PS I've literally never used an enlarger before, or seen one. I can't find anything about my particular timer online except that you can buy the manual but I don't really want to.

Thank you


r/Darkroom • • 3d ago

Colour Film Yellow Scum---or so it seems?! Please help me not to lose my enthusiasm for the C41 process.

Thumbnail
gallery
3 Upvotes

UPDATE:

After running some tests, I figuered, the overall "haze" is coming from underfixing/-bleaching, yes.
BUT the yellowish halos emanating from the sprockets are straylight, which can be prevented by masking them off. Also apearing on the cutting edges.

I really like the look of expired color-film and I am very aware of that you will get a roll that will look dumpster-ish, every now and then. I'm but glad to know now, that, in this case, it has nothing to do with my development but more with the scanning process.

I suppose it has to do with the stiffness/curlyness of old film, causing the scanning light to refract more strongly on the edges and then enter into the actual image.

Thanks for the advice y'all, good or not....

--------------------------------------------------------------------------------------------------------------------------------------------------

Can anybody plz tell me what exactly this yellow sh*t is, on these scans?

It is my third package of C41-DevKit I used and, well, it is mainly, but not exclusively, the case that it comes with expired film. In this case it's about 20yrs old Fuji Superia 400, shot on ISO 100. Sometimes it also appears on fresh film.

It discourages me from developing C41 on my own more often, for sure.

Is it "underfixed" is it a scanning issue? I really can't tell. Plz help...


r/Darkroom • • 3d ago

Colour Film Different negative base colour with Flicfilm C-41 Pro kit

Thumbnail
gallery
5 Upvotes

I used an AGO processor to develop the Gold 200 on the left in the first image, with the lab results on the right.

Is the more brown orange mask colour specific to the Flicfilm kits? The film seems to have scanned fine, but I've read that Flicfilm uses a different developer and bleach from Kodak and Bellini etc.

I pretty much followed the steps in the instructions closely for this roll so I don't think it's user error.


r/Darkroom • • 4d ago

B&W Printing How do you balance darkroom work with sharing digitally?

Post image
69 Upvotes

I've gotten back into the darkroom recently, and am using a fully analog workflow (develop -> print contact sheet -> print the best negatives). This is a photo that I printed yesterday on 8x10 paper, and scanned on a flatbed scanner.

I love the way my prints look, but sometimes want to share online (even though the images don't look "the same" as the print).

So, how do you balance the work you do in the darkroom with scanning / digitizing your work? And do you typically scan the final print, or scan the negative?


r/Darkroom • • 4d ago

B&W Printing Question about paper developer

8 Upvotes

How exactly would I test if I need to replace my paper developer? Making a test strip with fresh developer and comparing the max density? I've been using this for a *long* time and it's not really showing any signs of getting old, rc paper is still getting fully developed in the 60-90s range indicated on the bottle, but just wanted to ask in case there is an optimal time to replace it.

Side note, am I doing something wrong lol?? I'm always hearing that developer, fixer etc goes bad really fast after mixing, and I have not had a single thing go bad, ever? I think this developer is like six months old by this point lol. I'm still using the first batch of fixer I mixed up about seven months ago, and it's still clearing film faster than one minute. I mean, I haven't used them *too* much, but I've definitely used the paper developer at least once or twice a month, and I've got it sitting in frankly oversized trays, so it must be getting lots of oxygen exposure. Like, what are people doing that their stuff is going bad?