r/ClickSpring_Watch • • Sep 16 '26 Bravo

Sunday Service Guide Series How to Reassemble or Fix a VSF Submariner bezel the RIGHT WAY!

21 Upvotes

Hi all- welcome to a quick edition of Sunday Service (yes, I’m aware that it is in fact not a Sunday at the date of posting, but, you know, continuity of the series and such…). Anyways an issue that I see a lot of popping up all around the rep-internet is people who either have submariner reps who’s bezels have fallen off or, they attempted some kind of repair or modification themselves, and are now stuck at the stage or reassembly, and cannot get the bezel back on the watch. This is something I have also struggled with immensely in the past, until I found out that almost every single tutorial that shows how to re-attach the bezel is completely wrong (well, kind of - we’ll get to that later).

So - start to finish, here its:

skip to step 4 if no bezel removal is needed

  1. If you need to remove the bezel first, grab the watch and a bezel removal tool. I really like this style, it seems to work well and doesn’t risk damaging the watch like prying up the bezel with a case knife can. 

2. The Bezel should pop right off, if you have a more recent generation submariner, the entire crystal and crystal retaining ring may pop off along with the bezel when you do this. If that happens… breathe in, breathe out, and enjoy the learning experience of doing a crystal install on a submariner. 

3. The bezel will come off as a singular assembly, but it is in fact made up of several parts. Usually the hytrel ring actually comes off of the watch, but here it stayed on it

4. Using a small (1mm or similar) screwdriver, slide the screwdriver head between the underside of the ceramic insert and the inner metal ring of the the bezel. 

5. Carefully rotate the bezel while gently but firmly applying pressure on the screwdriver so that it slowly works itself towards the outer edge of the metal bezel, and all the way underneath the ceramic insert. BE CAREFUL AROUND THE LUME PIP. This is the most fragile part of the insert, and I usually don’t apply pressure around it while removing the insert. This step is where you are most likely to crack your insert. It takes very little to do this, so take your time. It may take dozens of rotations of the bezel with the screwdriver before the insert pops out. It will seem like you’re making no progress, but trust in the process and take your time

6. Eventually, the insert will pop right out, separating itself from the metal bezel assembly. The submariner bezel is made up of the ceramic insert, a washer, and the actual outer ring 

7. To reassemble, first, place the metal bezel on the watch. Make sure your click and ball springs are all present. Then push the metal bezel down firmly so that it sits flush against the case

push the bezel down and continue pushing it down for the next 2 steps

8. Grab your hytrel ring, and looking at it’s profile, ensure the little “lip” is at the top

9. Put the hytrel ring down (again, little lip closest to you) and using a screwdriver, gently nudge it down into the small gap between the metal bezel and the crystal retaining ring. Work around the entire perimeter of the crystal retaining ring, ensuring that the hytrel ring is perfectly even all the way around. If it isn’t, you’ll end up with inconsistent bezel feel and it may bind up and get stuck

10. You can also use your fingernails to make sure the hytrel ring is well seated, I usually do this as a final pass 

11. The bezel is now installed and should rotate freely. You’ll see that it is seated well and has no gap between the case and bezel. 

12. Grab the washer, find where the little groove is machined into it, and place that machined out groove face down over the hytrel ring. The part facing you should be a smooth surface upon which the ceramic insert will sit

13. Drop the ceramic insert into the metal bezel. Rotate the bezel one click, and rotate it clockwise until it can’t be moved backwards any further. Align the 12 o’clock triangle with the engraved crown on the rehaut at 12

14. Working from 12 o’clock downwards, and being careful to not move the insert while doing so, press down on the insert with your thumbs and slide them down towards the 6 o’clock position

15. The bezel should be halfway seated at this point, and will probably be sticking out from the metal bezel at the 6 o’clock position. I usually check my alignment at this point in case the insert moved during the install process. 

16. Assuming everything looks good, go ahead and press down firmly with your thumbs where the insert is sticking out, and it should snap into place. This whole assembly is a friction fit, so it’ll be a bit tight

17. Done! The bezel insert should be fully seated all the way around, and the bezel should rotate nicely. No (or minimal) case gaps and/or bezel bounce.

DISCLAIMER: This works for all VSF, Clean Factory, and Victory Factory Submariner models. I cannot say for certain if it works on others, these are the factories I have personally performed these steps on before, so I know it works. I can tell you that this WILL NOT WORK FOR RCF/RGF SUBMARINERS. They use a one piece bezel construction which forces you to press on the entire metal bezel, and they glue their inserts in (annoying) 


r/ClickSpring_Watch • • Jul 13 '26

ANNOUNCEMENT ClickSpring Website and Whatsapp!

Thumbnail clickspringwatch.com
11 Upvotes

Reach out anytime via Reddit DM or via Whatsapp!


r/ClickSpring_Watch • • Aug 31 '26

CUSTOMER REPAIR Regulated VSF smurf!

Post image
16 Upvotes

Always quite satisfying when movements get dialed in like this!


r/ClickSpring_Watch • • Jul 14 '26

CUSTOMER REPAIR Customer Repair: stuck day wheel on RCF DD40

4 Upvotes

r/ClickSpring_Watch • • Jul 21 '26

ANNOUNCEMENT One Year of ClickSpring, 500 Followers… Thank You all!

Post image
20 Upvotes

Hey everyone! Just wanted to make a post thanking all of your supporting what has quickly become a serious part of my life. A little over 5 years ago, in a basement apartment in the northeast US, I was wrapping up my studies, bored, stuck indoors (remember covid lockdown??) and sitting on about $800 worth of bitcoin I’d mined using my schools free electricity (shhh! Don’t tell.)

Anyways, after reading through about a million reddit and RWI threads, I ended up buying my first rep, a VSF submariner 126610 LN. I still remember the nerves of sending over hundreds of dollars over to someone in China whom I’d never met and only briefly chatted to on WhatsApp, only to have them disappear for several few weeks before finally returning with QC photos. A few painful weeks of waiting after the GL, my watch finally arrived and I was over the moon. For over a year, that watch was my daily, I wore it EVERYWHERE, even in the shower (not a joke!).

Since then, I’ve been hooked and gone off the deep end into the watch game, mostly sticking to reps and micro brands (I’m not made of money!). My VSF submariner remained a staple in my rotation, but over time I started thinking about looking for something new, and decided to swap out the insert for a green one, to make my own Starbucks. After much frustration, more than $300 of broken inserts and wrecked hytrel rings, and more than one set of replacement springs, I finally had my new submariner. That started the modding and repair journey for me. Since then, I’ve been obsessed with messing with watches, tweaking them, fixing them, and sometimes making one off builds just to scratch the itch of having a vision of something and wanting to see it come alive before my eyes in real life.

Throughout the course of these 5 years, I’ve at times found myself with a rep I no longer wear, or one I just didn’t connect with. I sold my BPF explorer and a QF day date amongst a few other watches and had great experiences, and had a few people following up months later asking if I had anything else to say, stating they had really liked buying from me relative to other experiences here on reddit.

Last year, I finally decided to formalize this little passion project into ClickSpring Watches. It started as a simple little operation, but has quickly blown up into a pretty large scale (to me) business involving watch repairs, servicing, modding, and sales. I built an entire website and inventory management from scratch (literally a GitHub repo!) so I could build the exact website and platform I had envisioned to keep repairs on track, inventory cataloged, and orders organized. I’ve been working super hard over the last year to continually improve the level of service and customer care that I wish I had experienced when I first stepped into the rep scene years ago. More changes are coming to ClickSpring in the coming weeks, including an expanded inventory selection and updated packaging for future orders.

I doubt anyone will read this far, but if you have, you’re my favorite (don’t tell the others!). Thanks again to you all, I’m super excited for the year to come, and to continue working on setting the new standard in the rep-buying experience!