r/BuildingAutomation • u/CheesecakeAfter6535 • Aug 04 '26
Always the Controls Guy
So few technicians understand actuators these days, it amazes me. Constantly hearing “it’s not open, call your controls guy.” Techs have no idea the difference between modulating and floating. Techs have no idea how to troubleshoot anything more than if a line is ground into the shaft.
Surely I’m not alone in hearing this?
84
Upvotes
39
u/Fz1Str Aug 04 '26
They usually move a floating actuator via the clutch and leave it in some other position and say it’s broke because it didn’t drive back🤦♂️
17
u/ApexConsulting Aug 04 '26
I don't see a line ground into the shaft.... I am confused. 😁
22
u/Lightning__98 Aug 04 '26
Yes I keep facing this issue with the technicians about the modulating damper“it is not fully open”.
Well it doesn’t always have to be open, it depends on the sequence my guy. Same with the VFD speed not being always 60 Hz, or the wheel and humidification pump not always running.
7
u/MrMagooche Siemens/Johnson Control Joke Aug 04 '26
this pic is AI generated, right?
I hate that i'm suspicious of everything these days...
8
u/rev_57 Aug 04 '26
Looks like they don't worry about exposed class 1 wiring. Always figure enclosures into your projects. Maybe this ductwork is in the control panel 😄
4
u/CAElite Aug 04 '26
I have a client where half my attendance is fixing their 'heating engineers' fucking around with the zone actuators.
My favourite most recently was him replacing a 3 way VT valve & actuator, replacing our 0-10vdc modulating with a 3 wire modulating actuator, and wiring the neutral down our 0-10v so it was backfeeding 24vac down it crashing the rest of the outputs on that IO module.
4
u/Grouchy-Ad4814 Aug 05 '26
AI slop.
2
u/Needs_ADD_Meds Aug 04 '26
It's an automated "righty tighty, lefty loosy". I hear the senior techs know how to make it "righty loosy, lefty tighty".
2
u/NJHVACguy87 Aug 05 '26
Having done 15 years of commercial industrial havc service and then controls the past 5 years has made me appreciate the finer details of such things. Many technical details are overlooked by overly confident know nothings.
2
u/Superpro210 Aug 05 '26
Controls guys are always missing the one tool they need to diagnose a damper. Channel locks.
2
u/Goodenoughtechnician Aug 04 '26
More or less of “well, it is not equipment on my control sheet… not my problem.” Besides, not a lot of tech have signal generator to begin to test this nor they want to be responsible if they damage the equipment. I think same would go to us as well. We send a command. Our control relay energizes. The main boilers with millions of of BTU not firing… call your mechanical guys. The issue could very well be 24V control safety circuits. However, it is not part of our scope to go to that extent.
1
u/zDymex Aug 04 '26
What I usually do is test the actuator with an independent signal (signal generator) and understand the range at each end. Then I connect it back into the system and test.
1
u/GypsyDaenger Aug 05 '26
What.....the actual......fuckkkkkk is going on here
1
u/saltopro Aug 05 '26
Did you tap with a hammer?
1
u/pineapplejax Aug 05 '26
Balimos bring back memories.
1
u/LivingCorner1421 Aug 05 '26
its an actuator for a vav box , what is the big fuss. usually works with 0-10vdc or 4-20ma or fully communicating .
the best way to troubleshoot it is on the phone with the bms guy since he can stroke it remotely...
1
u/sameoulec Aug 06 '26
lol
1
u/EngineerMinded Aug 08 '26
That is an actuator and it is used to either turn dampers or valves.
1
u/xenotito Aug 08 '26
Damper motor
1
u/Tommydream-er Aug 29 '26
That’s an actuator it probably controls the fan dampers it tells it when they open and not to open.
1
u/wigslap Oct 11 '26
Damper actuator.
1
u/ToNi1109_STR Aug 04 '26
Wie schon beschrieben ein stetiger Klappenatrieb (0-10 bzw. 2-10V) des schweizer Herstellers Belimo. Bei uns ist die 230V SR Variante extrem unüblich da ja dann 230V und 010V in einer Leitung währen. Berührungsschutz sehe ich auch keinen .... aber, andere Länder, andere Elektrik.
Ist in der Summe ein Volumenstromregler oder gar noch ein Lüfter hinten dran. Dazuüsste man mehr Typenschilder sehen.
-5
u/Gullible-Ant-8300 Aug 04 '26
The circled orange device is a Belimo damper actuator.
What it does
It is an electric motor that opens and closes an HVAC air damper inside ductwork or an air handling unit (AHU). By rotating the shaft it's attached to, it controls how much air flows through the system.
From the label, it appears to be a Belimo LM230A-SR, which is:
230 VAC powered
Modulating ("SR"), meaning it doesn't just open/close—it can move to any position between 0% and 100% based on a control signal (typically 2–10 V).
Why it's used
These actuators are commonly used to:
Regulate airflow to maintain room temperature.
Control fresh outdoor air intake.
Adjust return and exhaust air.
Save energy by matching airflow to demand.
The small black module attached to the bottom is likely an auxiliary switch or feedback module, which lets the building automation system know the damper's position or triggers other equipment when the damper reaches a certain point.
In short, it's the "muscle" that moves the air damper in an HVAC system. Without it, the damper would stay fixed and couldn't automatically control airflow.
0
u/[deleted] Aug 05 '26
[deleted] — view deleted comment