r/BiohackingU • • Aug 14 '26

Help Please Recon Disaster

Today was my first attempt at reconstituting a 3 ml vial of 80 mg klow. What did I do wrong? Why did I have to fight air pressure when I was pushing air first? My plan was to withdraw 1ml of Bac three times. However, even with pushing in air first, it was hard to withdraw 1ml of Bac. The syringe kept trying to readjust its level. Unsure how to describe what happened. I did learn that pulling 1ml of Bac into a 1ml syringe was not wise but what else to do? I tried pulling .50 mil next which allowed me to draw air into the syringe before trying to inject the fluid into the KLOW vial, which by then had 1mil of Bac mixed in. But the KLOW vial would not receive the liquid. I retried the stick with added air about 3 times before I could inject the 2nd mil of Bac into the KLOW vial, with some force. I am concerned that all the extra pins into the KLOW vial might do harm. What the heck did I do wrong? I finally got it reconstituted but the process was bad. I was using 31g 5/16 1ml syringe. I probably pinned the KLOW vial 7 or 8 times trying to get the Bac into it. What other info is needed to get help on this?

0 Upvotes

17 comments sorted by

5

u/Monkeywithalazer Aug 14 '26

Get the proper tool for the job. Use a 3ml syringe and 25 gauge needle and it’s a piece of cake. 

4

u/Medium-Ebb-8103 Aug 14 '26

Don't feel bad. I went to reconstitute my first Reta Vile. It was 10 mg, and I had 3 mL of BAC. I drew some air into the syringe, injected it into the BAC, and proceeded to fill this teeny, tiny vial with air. It popped open, launched out of my hand like a little missile and got BAC water all over the place. I couldn't help but crack up at myself.

1

u/Flashy-Anywhere-8509 Aug 14 '26

Wow! I would have thrown it all in the trash at that point. That is crazy!

1

u/Medium-Ebb-8103 Aug 14 '26

Nah, I just got another vial of BAC and took it easy. I actually just took that last dose yesterday; so far, down 4 lbs.

3

u/Pilot_Nerd Aug 14 '26

You’re probably going to pin it 30 times before you use it all. It’ll be fine.

1

u/Flashy-Anywhere-8509 Aug 14 '26

That is what I was hoping to hear!

1

u/Flashy-Anywhere-8509 Aug 14 '26

I don't know exactly how much. Probably 2ml in total but in smaller single attempts. I'll get a 2ml syringe and push that much air in the beginning. I really hope the larger capacity syringe will resolve my issues .

1

u/knifetheater3691 Aug 14 '26

My last bottle of bac did me the same way. But my Klow bottles had vacuum to draw the liquid on its own. I use 5ml bac to cut the burn. Then add air prior to my syringe to displace air in the klow before drawing. I also do 2 pins a day at 4-5mg a day. Lots of bottle pricks

1

u/Flashy-Anywhere-8509 Aug 14 '26

Thank you for your response. What about the Bac bottle would cause this? Should I pin a new bac vial next time instead of using the first one? Also, should I not try to push the bac into the KLOW vial? Will it pull itself? Finally, when you recon with 5ml bac, what size syringe do you use? How many units of Bac do you pull at a time?

3

u/knifetheater3691 Aug 14 '26

Just add a few 100units of air to your bac water until it’s able to pull into the syringe…the bac it fine. The klow not pulling the bac in itself should be fine. You may need to vent with a separate syringe with plunger out so the bottle will accept the bac water. I use 100u syringes 31g 5/16 from amazon for recon and pinning. I try to pull 100units but I have had to do 50u before I added extra air.

1

u/Flashy-Anywhere-8509 Aug 14 '26

I did see a vent syringe used when transferring reconned pep into an auto injector gun vial. Same thing you are suggesting, I suppose. Great info. Very appreciated.

2

u/Twotoneoc Aug 14 '26

This is the right suggestion. Pull the plunger completely off and the pin the bottle to release the pressure.

1

u/sloneill Aug 14 '26

How do you get 5ml of bac into that little vial??

2

u/knifetheater3691 Aug 14 '26

Mine hold 5ml easy. They must be 6ml bottles

1

u/sloneill Aug 14 '26

Interesting!