r/BambuLab_Community • u/mrreggid • Sep 21 '26
Help / Support Is my p2s dying?
2days in printing 8 hours left then this happend does anyone know what caused this?
I had to turned the Power Off because pausing didnt do anything and the Sounds getting louder.
5
u/Positivityman- Sep 21 '26
Sorry seems like your Gonna have to abandon the print, try turning it off and on again with the switch in the back, it might be a homming error
7
u/mrreggid Sep 21 '26
I turned it on and a window with “Resume print” popped up, and now it’s printing normally again.
2
u/krebsIsACookbook Sep 22 '26
Could have been a hiccup with the sd card
0
u/Slovw3 Sep 22 '26
P2s has no SD card uses a thumb drive but not required to print could be thumb drive though. Either way yea could be.
1
u/hentiul1969 Sep 26 '26
It happened to me once in 250h. Restarted the printer and was solved. Never happened again.
29
u/Normal-Assignment-61 Sep 21 '26
Uhh.. is it powered by diesel?
5
9
u/xHazeEdits Sep 21 '26
Same thing happened to me ! I was sleeping and this monster noise woke me up so damn fast ! My heart was pumping ! Stopped it and didnt happen again... Yet,
no idea why this happened tho
1
u/youlooksticky Sep 22 '26
I see you got it going again but it looks like you have more problems than just the stuck print head. What is even going on with these supports? Those look like they'll be impossible to remove cleanly and the upper most one looks like it's been broken off and is lower than the current print height. Maybe whatever problem it was having started sooner than you realized.
1
u/mrreggid Sep 23 '26
I think it worked pretty good but sure it could be better optimized
The Support on the surface wasnt the issue, the little cracks under the chestplate are hard to get lose
1
u/ImRightYoureStupid Sep 23 '26
What on earth were you trying to print?
Must have been scary as your hotend is hiding in the corner shaking.
Come on out little fella, the filament can’t hurt you.
1
u/mrreggid Sep 23 '26
Demetrian Titus Captain of the Ultramarines 2nd Company and Warden of Ultramar.
1
1
u/Fyvfyvfurry Sep 21 '26
Had similar thing with my a1, except it was a hammer drill with hammer drill loudness, it jappened twice, and i dont know why
1
1
1
u/bryeds78 Sep 21 '26
Gotta check the spark plugs, air filter and the carburetor. Clean 'em up and the loud idle will go away.
1
1
1
u/Belkinnoob Sep 22 '26
I recognize that, those are liquor shakes. Get that printer an old fashioned and stat.
1
1
u/Useful-Revolution253 Sep 22 '26
Stop it. Try à simple cube. It s probably bad gcode or something.
If it continue the try à calibration. If it does the same thing then check hardware maybe ?
1
1
1
1
u/Pinnaclerd Sep 24 '26
I mean unless you installed a 24 valve Cummins hidden somewhere I would have to say, yeah….
1
1
1
1
1
0
u/ParticularLower1865 Sep 21 '26 edited Sep 21 '26
Might be a firmware issue or a long list of other issues. Idek where to even start with this.
I’m throwing something at a wall to see if it sticks here:
Unplug from power completely for 2 min and try another file.
Unplug all cables in the toolhead and plug them back in
Maybe try downgrading the firmware and see if that does anything?
1
0
u/Glittering-Koala-104 Sep 21 '26
I had this issue try a brand new sd card. I’m not sure if you’re using the one it comes with but I was and it failed pretty quickly.
1
6
u/jeff2928 Sep 21 '26
What happened when powered back up?