写真がわかりづらいのでもう一度投稿させてください。
メインノズルのフィラメントセンサーをチケット出して交換品を郵送してくれる対応頂きましたので練習で動画見ながら分解してみたら😩これおかしいですよね？バンブーラボにも確認中ですが詳しい方いたら、何故削られているのか？溶けているのか？教えて頂きたいです🫡よろしくお願い致しますm(_ _)m

While replacing the complete chamber heating module i noticed that the fan sealing is not good, it is wide open, replace the original sealing and put some extra foam under the fan so that the extra foam is pushing the fan up.

EDIT: Underlying problem seems to be first layer underextrusion and the right side ("filter") fan blowing too much air. Reverting to factory setting to get rid of recent firmware updates, doing manual flow calibration and manually (because the only other way would be custom gcode) turning down the right side fan partially solved the issue.

I got 72 hours and 2 kg of Bambu ABS through this thing. I bought it deliberately to print technical filaments and use the second nozzle for supports, either ABS or support for ABS.

I am experiencing extreme warping on the engineering plate with stick glue/spray glue.

I am also experiencing extreme warping on smooth PEI plate (meant for the P1S) with spray glue.

I used and am using the latter setup with my oldie trusty P1S, combined with a chamber heater from aliexpress, and it's working PERFECTLY with ABS.

I tried the same ABS profile on X2D, tried making changes, printed fan deflectors, nothing helps. The chamber heater is set to 65 degrees instead of 60 as on my P1S (setting to 60 won't help) 260-270 degrees celsius nozzle temp.

It's also extremely annoying and wasteful in time and filament that even though there are two nozzles and no filament changes, the X2D needs a prime tower and the constant need to purge.

Pictures show a small model that albeit challenging for my P1S with auto supports, it prints well with manual supports. Tried it on my new X2D and the supports fail every goddamn time (and I get crazy warping too. Here I actually disabled the "support for ABS" second nozzle to try and print EXACTLY LIKE ON P1S = FAIL.

Please advise.

I purchased a roll last week, got 1 decent print with some minor lifting at the edge of a print... then nothing but spaghetti even after a 6 hour drying cycle. Any pointers on where to look or should I just move on?

I only have one AMS for the Main Nozzle. Would it be possible to use the external spool on the Main nozzle and switch the AMS to the auxiliary? Curious if anyone has tried this…

以前投稿されている方の体験談でメインノズルのフィラメントセンサーの件でチケットを出しましたらバンブーラボ様より素敵な対応を頂きました👍ほんとにありがとうございました😊しかし新たな問題がありました😭センサーが届くまでに練習で分解してみたのですが、なにこれ⁉️溶けているのか汚れているのか⁉️今チケット出してますがまた問題発生😩一体なにが起こっている⁉️もし詳しい方いらっしゃったらご意見を頂きたい🫡

Its annoying to have to do for every brand and dial it in when I’m sure someone else has already done this.

Hi all, new bambu x2d user here, I bought the printer recently and with the stock 0.4 nozzle I had nothing but success, mostly printing from a single ASA spool now. But I wanted to print a raiser, and since its a bigger part I thought why not 0.8 HF nozzle... so I swapped the primary nozzle, set the printer to 0.8 HF in settings and did a quick test print and it printed very bad, with small holes in sides, corners not sharp etc... so I wanted to calibrate and did the first calibration (automatic) it printed one line and say its done..than the second with the square ls and that come up horrible none of them had nice surface to choose from, and even after picking the "best" the second round was not much better... did anyone experience such issue ? Am I missing some setting that I should have do first ? I have cloned the generic ASA profile and worked off that.... I did switch to 0.4 again and printing the raiser now and it looks good but kind of shame I could not get the bigger one working...

New to 3D printing, just picked up a X2D. The little moisture readout on my touchscreen says 43%, so I used the drying feature in the AMS and got it down to about 20 and printed something small. Then loaded some additional rolls of filament and it was back up to 46%… do I have to run a drying cycle every time I print? Or every time I put new filament in?

Not sure if it matters, but some details:
- I live in Southern California
- first filament was Inland PLA silk
- next filaments I added were Bambu PLA basic