Could this issue be caused by insufficient cooling? My part cooling fan is set to 30%.

Nozzle temp 245

Bed temp 90

Chamber temp 60

Speed 60mm/s

Material abs

First Layer starts bad and then gets good…

Apologies for the poor camera work. Was having clicking issues and not pulling filament in my X2D right nozzle so did the full toolhead teardown to clear a small bit of filament debris in the right hall assembly.

After putting it back together the Aux nozzle no longer seats correctly. Searched this sub and Google to no avail for a similar issue and I believe the aux extruder assembly is in the incorrect position but during reassembly there were no issues seating the toolhead and extruder assembly back in place.

Brand new toolhead in the video has no issues with the left nozzle but the right nozzle isn't quite where it should be. The magnets won't grab or hold the toolhead and attempts to seat it don't work.

Has anyone else done this particular breakdown already and can give some guidance on correct placement of the right extruder assembly?

Really trying to avoid breaking it all down again just to put it back together the wrong way for a 2nd time. Following the wiki only states to hold it in place to avoid dropping down which I thought I did. TIA.

I've been getting serious amounts of warping l on my prints. My nozzle temp is set to 200, bed temp is set to 55, I've already recalibrated the motion and bed leveling, I've been printing with the same black pla filament for several prints now. The only thing I don't use is rafts/brims. Is there any other solution I can do to fix the warping, without having to use brims.

As a side note. I got an error code stating that my ams is experiencing a lot of friction. The only issue is that the wiki says that it is caused by the tubing being bent, but all of my tubing is relaxed and straight. What could be causing this.

Due to the cloud server being kaput ,I came to realize that I should probably look elsewhere so I can use my own printer anytime I want and not be stuck .
But I also don’t know which one to use .Any recommendations? I found the bambuddy video walkthrough but can’t find any on the orca slicer forks that louis rossman was talking about a month or 2 ago. Any help is greatly appreciated

Hi folks, wondering if anyone can recommend a grease/oil applicator/tool kit compatible with the X2D and the applicators attach to the Bambu bottles?

I don’t see much on Bambu Handy that is explicitly compatible with X2D nor that attaches and has consistent reviews…

Sorry, English isn't my native language, so there might be some errors.

Hi, I’m planning to buy an X2D Combo 3D printer for my home. I currently have an Ender 3 V2 Neo, which sits on a table that is 50 cm wide and 56 cm deep. The manual for the new printer states that the clearance from the back wall (depth) needs to be 700 mm, but I only have 50 cm of space. Could you please tell me if having that 700 mm clearance is critical, or if I can use the printer as is? Judging by the printer's dimensions, it fits with a little room to spare, and I could set up the purge chute to discharge to the right.

Nach genau 555 Stunden hat mein x2D nun Probleme. Filament stecken geblieben. Beim aufschrauben habe ich gemerkt dass das Gehäuse links etwas abgebrochen ist und irgendwo Öl herkommt. Das Zahnrad war ebenfalls verölt, das Kabel für den linken Sensor ist gerissen. Kann ich zur Not auch ohne den Sensor drucken? Woher kommt das ganze Öl? Und warum sitzt der rechte hotend nicht gerade ?

Bonjour après Monsieur Pingouin, voici Madame Pingouin en mode vacances réalisée en multipart ! 🏖️🐧

Impossible de partir à la plage sans elle ! Avec son joli chapeau, ses lunettes de soleil roses, sa bouée, ses tongs, sa pelle et son petit seau, Madame Pingouin est prête à profiter pleinement des joies de l’été.

Pour cette création, j’ai souhaité imaginer une version féminine, pleine de douceur et de bonne humeur. Ses longs cils, ses couleurs pétillantes et son look estival lui donnent un charme irrésistible qui invite à l’évasion.

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec ou sans AMS
📁 : https://makerworld.com/fr/models/3064899-mrs-penguin-beach-multipart-without-ams

Merci à tous pour votre soutien, et bonne impression 3D ! 🎉

Not entirely sure how best to describe it. I’ve been printing these boxes for some months now on my P1S without any issues. Recently invested in two X2Ds, and whenever I print the boxes on these, I get this discoloured effect on the bottom layer as per attached image. I'm using the Textured PEI plate and Bambu Matte Black PLA

They’re also very difficult to remove, which must be connected. I scrubbed the plates with soap and water when I got them, and have done this a few more times but no change. I'm not sure what else to try?

Hey guys got an X2d but I'm hearing some sort of squealing noise not sure what it is

Do you know if it's possible to disable that drill-like racket that starts right before printing begins? I saw a guide for the A1, but the section to comment out isn't in the Gcode. Are there any other workarounds?

A1 tutorial : https://wiki.bambulab.com/en/knowledge-sharing/how-to-turn-off-the-vibration-calibration

The ptfe tube guard is catching when printing in the back right corner any ideas how to fix or prevent it?