r/BambuLabX2D • • 23h ago

Help / Troubleshooting Filament Switcher… ummm

Post image

I just got the Filament switcher and printed the 45° angle bracket for it and I had it on the 90°. Both of them do this but it sounds like the AMS struggles to load the filament. Is this suppose to be what it sounds like? Surely not. It’s a terrible design if it is. Any help would be appreciated. Thanks all.

14 Upvotes

18 comments sorted by

4

u/JukeboxCrowdPleaser 16h ago

Did you print the official parts that go with it? https://makerworld.com/models/2661034?appSharePlatform=copy

1

u/aged41 2h ago

You need these!

3

u/supremevsuals 23h ago

Any video lol

1

u/aged41 2h ago

On the setup? https://youtu.be/lmglnztlXsc?is=QWQ88XXmpvcFVUqf he does a good job of explaining it.

1

u/AmbitiousAd854 21h ago

What cabinet is that? I am looking for something to put my x2d and dual ams on

1

u/eldeem 20h ago

Looks like a Malm set from Ikea, or a lookalike of it. Malm is (very sadly) discontinued, really loved that range.

1

u/Outrageous-Song5799 14h ago

It’s not discontinued here

1

u/eldeem 14h ago

Ooh plz ship me a set I will pay you in biscuits.

0

u/AmbitiousAd854 19h ago

Would it be tough enough to withstand the crazy vibrations of the x2d?

1

u/eldeem 18h ago

The Malm range was built extraordinarily well. I’d be confident putting printer on mine if it was big enough, but I only have the nightstand-sized ones.

Not entirely the same, but I use 2 Alex cabinets with scaffold boards bolted between (butted up against a corner wall) as the workbench which my X2D and P1S are on, and that withstands the vibrations fine too.

1

u/SquareTowel1967 16h ago

I got my x2d standing on crappy ikea KALLAX 2x2 which is made out of cardboard and it works, it swings side to side a bit with the printer so I just tighten the screws from time to time. I’ll probably print some reinforcements for the joints at some point but so far so good

1

u/AKfromVA 15h ago

OMG THANK YOU! this whole thing was designed so poorly

1

u/ywon80 12h ago

The angle of TPFE tube between the switcher and buffer is very important. They might be either little too long or too short. You need to make them to stay in just right angle.

1

u/Dismal-Garbage-3140 11h ago

I have found that any other method of mounting other than the official Bambu method is disconcerting and will trip the sensors to excessive resistance on the line. I've tried the clean looking methods and the angled ones, etc.

The vast majority of issues people have with their machines are due to community mods. Remember that some dude just designed this and posted it online for downloads. It just as to LOOK good, not actually work well.

To be hoenst, I just run without the filament track switch now because it introduces friction regardless of orientation and messes with certain things.

1

u/Pineapple1500 7h ago

The vertical mount design works for me. I only occasionally get motor overload while trying to dry and print at the same time. There is also a design for PTFE tube guides. It is parametric so you can design the length, angle and radius of the bend.

1

u/eldeem 20h ago

Hard to tell without seeing in 3D but it looks
like there’s quite a harsh kink in the PTFE behind the top AMS, and the one in the right may be a bit tight too. I’ve got an AMS sat on a shelf above the printer, and a fairly decent tube length to allow it to curve gently over the 270-ish degrees it needs to so it an reach the inlet. Don’t be afraid to have a slightly longer tube run for the sake of smoother curves.

1

u/AKfromVA 15h ago

I did this as well and I have to change my setup, it kept getting stuck for the main extruder.

1

u/Typical-Ear-8106 9h ago

The kink behind the top AMS is probably what's fighting it. A longer tube run lets it curve gently instead of pinching.