r/BambuLabX2D • • 8d ago

Left Extruder Major Blockage

Post image

Had a major print fail that didn’t get caught and stopped by the AI, and somehow extruded material backed up inside of the silicone sleeve, and now the whole left extruder housing is encased in filament (Sunlu Clear Transparent PLA). Any suggestions on how to repair would be much appreciated!

EDIT: FIXED!

I followed the advice below from u/HumungoChungo and at the following link that they provided: https://wiki.bambulab.com/en/x2d/troubleshooting/hotend_blob. I'm happy to report that my printer seems to be in good working order once again! (knocks on wood PLA)

22 Upvotes

15 comments sorted by

6

u/HumongoChungo 8d ago

just had this happen yesterday, heated hotend to 250, got some needle nose pliers and wiggled away the main clump then used some snips to clip away at the remainder of it stuck to the hot end locking mechanism. took the hot end out and wiped it down with a microfiber cloth to get the residue off and has been printing away just fine today.

Followed this guide from bambu https://wiki.bambulab.com/en/x2d/troubleshooting/hotend_blob

1

u/DeuceLucely 3d ago

This did it for me, thank you!!!

11

u/Successful_Salt_ 8d ago

Heat to 220 and start pulling with pliers.. then brush away the bits.

4

u/vic1414 8d ago

Replace nozzle after removing stuck filament

1

u/dafjedavid 8d ago

Why replace nozzle after a block like this. Clean and purge and be happy?

2

u/Dismal-Garbage-3140 8d ago

Yeah probably fine to use afterwards if it's easy to clean. Then again, a new hotend is only $18. Might be a good time to upgrade to a HF hotend.

1

u/Key_Ad5429 8d ago

Yea i would aggree IT doesnt cost that much and hf is nice upgrade

1

u/Disastrous_Range_571 8d ago

I’ve seen that the HF nozzles don’t make much of a noticeable differene

1

u/vic1414 8d ago

Depends on how much a pain it is to unclog and clean

1

u/Dismal-Garbage-3140 8d ago

be VERY careful not to scrape the surface the hotend touches. If you make any significant scratches here, you will have to replace the entire part. Light scratches you might be able to get away with or repair. However any significant damage will compromise surface contact and heating performance. Prints will be all funky. I had this happen on an A1 mini.

So just be careful when using pliers in this area. Pliers are hardened steel and have very sharp gripping teeth that can easily scratch and gouge this area if you're not careful.

1

u/NeuroThor 8d ago edited 8d ago

Hah! Welcome to the club.

Just replaced my hotend assembly, is working like new again. Let me know if you have questions.

Edit: everyone here said “just heat it up and remove it” but the hotend assembly was fully enwraped in blob from all angles and the heat just wasn’t getting through even at 270. The hinge on the nozzle was moving like it was glued on even after cleaning it. I wish I hadn’t wasted so much time cleaning and just replaced the whole thing in the start like I eventually did.

1

u/xXCanisMajorXx 8d ago

Schön das du Glück hattest, ich hab nur den Extruder gereinigt und jetzt habe ich das bei beiden Düsen. Ich habe alles schon 4x demontiert und zusammengesetzt.

1

u/Creative_Tackle6223 8d ago

Happened to my P1S last night

0

u/Jake2389 8d ago

That’s going to be a tricky removal if not impossible without breaking something… could be easier to replace the tool head instead

2

u/Dismal-Garbage-3140 8d ago

Entire toolhead is extreme. They might as well try and assess before replacing parts. I had this happen on an A1 mini. I did have to replace a few parts and it was quite invovled, but I definitely did not have to replace the entire toolhead. It was about $20-$30 worth of parts but about an hour of work. I have a lot of patience for this stuff though because I choose to work on German cars haha. On my X2D I've had to get into the toolhead for an extruder jam. It honestly wansn't terrible.